Sony ILCE-7 / ILCE-7K / ILCE-7R (serv.man2) Service Manual ▷ View online
ILCE-7/7K/7R_L2
2-5
2-1-3. MAIN BOARD SECTION
ns: not supplied
DISASSEMBLY
1. Remove in numerical order (
1
to
3
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇
: Solder
2
Remove the flexible board (
2
) → #2 X 2 (ILCE-7R)/
#1 X 2 (ILCE-7/7K) → #12 X 1(ILCE-7/7K)
Screw
2
#2
Back View
Back View
ILCE-7R
ILCE-7/7K
#1
#12
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
X-2582-400-1 VM VF LENS ASSY
102
A-1974-836-A ES-1001 FLEXIBLE BOARD, COMPLETE
103
4-480-818-01
SHEET (VF), EM SHIELD
104
4-438-854-01
SHEET, VF RADIATION A (ILCE-7/7K)
104
4-480-798-01
VF SHEET, RADIATION (779) (ILCE-7R)
105
A-1975-204-A SY-1022 BOARD, COMPLETE (SERVICE) (ILCE-7R)
(Note 2)
105
A-1983-492-A SY-1022 BOARD, COMPLETE (SERVICE) (ILCE-7/7K)
(Note 2)
106
A-1974-839-A AN-1003 FLEXIBLE BOARD, COMPLETE
BH0601 1-251-928-21
HOLDER, BATTERY (Note 1)
BT0601 1-756-134-15
BATTERY, LITHIUM (SECONDARY) (Note 1)
LCD902 A-2032-324-A ECX331CA-1 (SERVICE) (Note 2)
#1
2-635-562-11
SCREW (M1.7) (ILCE-7/7K)
#2
2-635-562-31 SCREW
(M1.7)
#11
3-078-890-11 SCREW,
TAPPING
#12
3-080-204-21 SCREW,
TAPPING,
P2
#1: M1.7 X 2.5
(Black)
2-635-562-11
2-635-562-11
2.5
1.7
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
3
#11 X 3 → #2 X 1
#2
#11
Back View
Note 1: Replace the battery holder (BH0601) together when replac-
ing the lithium secondary battery (BT0601) on the SY-1022
board. (The battery holder removed once cannot be used
again.) When mounting these parts, mount new battery
holder first and attach new lithium storage battery next.
board. (The battery holder removed once cannot be used
again.) When mounting these parts, mount new battery
holder first and attach new lithium storage battery next.
Note 1: SY-1022基板のリチウム蓄電池 (BT0601) を交換する場合は
バッテリホルダ( BH0601) も同時に新品に交換してください。
(一度使用したバッテリホルダは再使用できません。) 部品取
り付けの際は、先にバッテリホルダを取り付けてからリチウ
ム蓄電池を装着してください。
2
#2
#2
#12
#11
1
101
103
106
104
102
ILCE-7/7K
ILCE-7R
#1
ILCE-7/7K
ILCE-7R
3
105
BT0601
(Note 1)
(Note 1)
LCD902
(Note 2)
(Note 2)
BH0601
(Note 1)
(Note 1)
ns
: BT0601 (LITHIUM SECONDARY BATTERY)
Board on the mount position.
(See page 6-47 of Level 3)
Board on the mount position.
(See page 6-47 of Level 3)
(Note 2)
2
TOP Section
(See page 2-12)
Overall Section
(ILCE-7/7K)
(ILCE-7/7K)
(See page 2-7)
Overall Section
(ILCE-7R)
(ILCE-7R)
(See page 2-6)
When removing and re-assembling,
pull this connector vertically from the board.
pull this connector vertically from the board.
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
3-078-890-11
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
Note
Note 2: Refer to “1-3. NOTES FOR REPLACING THE EVF DIS-
PLAY DEVICE (LCD902) OR THE SY-1022 BOARD” on
page 1-1.
page 1-1.
Note 2: 1-4ページの 1-3. EVF表示素子(LCD902)またはSY-1022基
板交換時の注意 を参照してください。
ILCE-7/7K/7R_L2
2-6
DISASSEMBLY
1. Remove in numerical order (
1
to
6
) in the left figure.
2-1-4. OVERALL SECTION (ILCE-7R)
ns: not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
151
X-2588-414-1 COVER ASSY, JACK (779)
* 152
4-480-628-01 PLATE, SY
153
4-480-796-01
PLATE, JACK BASE A (779)
154
1-846-474-21
CABLE, COAXIAL (85MM)
155
4-489-472-01
SHEET DP, FRONT COVER (779)
* 156
4-480-791-01 PLATE, WIFI
* 157
4-480-797-01
HOLDER, WIFI HARNESS
* 158
4-488-510-01
SHEET (779), SY ELECTROSTATIC
159
4-480-624-01 SCREW,
TRIPOD
(779)
160
A-1998-752-A COVER ASSY, FRONT (779)
* 161
4-480-822-01
GASKET (CN), EM
162
4-539-313-01
SHEET (779), LA
163
4-539-314-01
SHEET (779), LB
ANT101 A-1896-175-A AN-1001 BOARD, COMPLETE
ANT901 A-1998-750-A NFC BLOCK ASSY (779)
ANT901 A-1998-750-A NFC BLOCK ASSY (779)
#2
2-635-562-31 SCREW
(M1.7)
3
#2 X 1
Front View
#2
Screw
5
#2 X 1
Bottom View
#2
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
When removing and re-assembling,
pull this connector vertically from the board.
pull this connector vertically from the board.
Imager Block Section
(See page 2-8)
#2
#2
#2
#2
ns
ns
ns
#2
#2
1
151
3
ANT101
2
ANT901
5
159
152
158
153
154
156
157
155
160
162
163
(Claws)
(Claws)
6
Battery Block Section
(See page 2-13)
4
(Claws)
161
6
#2 X 3
Back View
#2
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2014.07
ILCE-7/7K/7R_L2
2-7
2-1-5. OVERALL SECTION (ILCE-7/7K)
ns: not supplied
DISASSEMBLY
1. Remove in numerical order (
1
to
7
) in the left figure.
Screw
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
1
#12 X 2 → #2 X 1
Top View
Back View
#12
#2
#12
2
#12 X 2
#12
Back View
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
201
4-480-630-01
FRAME, TOP G (778)
202
X-2589-158-1 TOP FRAME L ASSY
203
X-2588-415-1 COVER ASSY, JACK (778)
* 204
4-480-628-01 PLATE, SY
205
4-480-796-01
PLATE, JACK BASE A (779)
206
1-846-474-21
CABLE, COAXIAL (85MM)
207
4-489-472-01
SHEET DP, FRONT COVER (779)
* 208
4-480-791-01 PLATE, WIFI
* 209
4-488-510-01
SHEET (779), SY ELECTROSTATIC
210
4-480-624-01 SCREW,
TRIPOD
(779)
211
A-1998-753-A COVER ASSY, FRONT (778)
212
4-489-139-01
SHEET, DL FPC
* 213
4-480-822-01
GASKET (CN), EM
ANT101 A-1896-175-A AN-1001 BOARD, COMPLETE
ANT901 A-1998-750-A NFC
ANT901 A-1998-750-A NFC
BLOCK
ASSY
#2
2-635-562-31 SCREW
(M1.7)
#12
3-080-204-21 SCREW,
TAPPING,
P2
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
When removing and re-assembling,
pull this connector vertically from the board.
pull this connector vertically from the board.
Imager Block Section
(See page 2-8)
#2
#2
#12
#12
#12
#12
#2
#2
2
203
1
201
202
4
ANT101
3
ANT901
6
210
204
212
205
206
208
211
(Claws)
(Claws)
7
Battery Block Section
(See page 2-13)
5
ns
ns
ns
209
207
(Claws)
213
4
#2 X 1
Front View
#2
6
#2 X 1
Bottom View
#2
7
#12 X 1
Back View
#12
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2014.07
ILCE-7/7K/7R_L2
2-8
2-1-6. IMAGER BLOCK SECTION
ns: not supplied
Ref. No.
Part No.
Description
251
1-886-243-11
ISP-008 FLEXIBLE BOARD
252
1-886-244-11
ISL-008 FLEXIBLE BOARD
253
A-1976-127-A MECHA DEVICE SERVICE (3000) (ILCE-7R)
(including IC6101 (CMOS imager) and IS-111 complete
board) (Note 4)
board) (Note 4)
253
A-1976-128-A MECHA DEVICE SERVICE (3100) (ILCE-7/7K)
(including IC6101 (CMOS imager) and IS-111 complete
board) (Note 4)
board) (Note 4)
* 254
Selection Parts IM WASHER (C), ADJUST (Note 2, 3)
255
A-1902-075-C MB CHARGE UNIT (456)
256
1-490-193-21
SHUTTER UNIT (AFE-3313)
257
4-480-795-01
BUTTON, LENS LOCK (779)
258
4-489-471-01
SHEET DP, N FRAME (779)
#197
4-185-990-01
MB SCREW, CHARGE UNIT FIXED
#238 4-287-436-01 SCREW
(M1.7)
#267
4-287-436-21
SCREW (M1.7) (Note 1)
Ref. No.
Part No.
Description
SELECTION PARTS
Ref. No.254
Select the optimum thickness of washer.
Part
No.
Description
* 4-185-999-01 IM WASHER (C), ADJUST (t = 0.05)
* 4-185-999-11 IM WASHER (C), ADJUST (t = 0.1)
* 4-185-999-21 IM WASHER (C), ADJUST (t = 0.15)
* 4-185-999-31 IM WASHER (C), ADJUST (t = 0.2)
* 4-185-999-41 IM WASHER (C), ADJUST (t = 0.25)
* 4-185-999-11 IM WASHER (C), ADJUST (t = 0.1)
* 4-185-999-21 IM WASHER (C), ADJUST (t = 0.15)
* 4-185-999-31 IM WASHER (C), ADJUST (t = 0.2)
* 4-185-999-41 IM WASHER (C), ADJUST (t = 0.25)
#267
(Note 1)
(Note 1)
#267
(Note 1)
(Note 1)
#238
#197
2
Imager Unit Section
(See page 2-9)
253
251
4
255
3
256
252
254
(Note 2, 3)
254
(Note 2, 3)
254
(Note 2, 3)
257
258
Mount Section
(See page 2-10)
(including IC6101 (CMOS imager)
and IS-111 complete board)
(Note 4)
and IS-111 complete board)
(Note 4)
1
ns
ns
DISASSEMBLY
1. Remove in numerical order (
1
to
4
) in the left figure.
#267
Back View
2
#267 X 3
Screw
#197: M1.6 X 4.5 (Tapping)
(Silver)
4-185-990-01
4-185-990-01
4.5
1.6
#238:
M1.7 X 3.5
(Black)
4-287-436-01
(Black)
4-287-436-01
3.5
1.7
5.0
1.7
#267: M1.7 X 5.0
(Red)
4-287-436-21
4-287-436-21
#238
Back View
4
#238 X 3
Note 2: The IM adjust washers (C) differ in thickness.
Make sure to return the removed IM adjust washers to origi-
nal places.
nal places.
When replacing IM adjust washers, refer to “SELECTION
PARTS” If the original state cannot be restored due to loss
of the IM adjust washer, for example, replace the Mecha
Device Service (3000/3100).
PARTS” If the original state cannot be restored due to loss
of the IM adjust washer, for example, replace the Mecha
Device Service (3000/3100).
Note 2: IM調整ワッシャ (C) は,それぞれ厚さが異なります。取り外
したIM調整ワッシャは,必ず元の位置に戻してください。
ま た,IM調 整 ワッシャを 交 換 す る 際 は, SELECTION
PARTS を参照してください。IM adjust washerを紛失するな
どして元の状態に戻せなくなった場合は,Mecha Device
Service (3000/3100) を交換してください。
Note
Note 1: Refer to “Assembly-1: Screw tightening sequence when
assembling the IM plate (3000)”.
Note 1:
Assembly-1: Screw tightening sequence when assembling
the IM plate (3000) を参照してください。
Note 3: Refer to “Assembly-2: IM Adjust Washer (C) putting posi-
tion” when you assemble.
Note 3:
組立時は Assembly-2: IM Adjust Washer (C) putting posi-
tion を参照してください。
Note 4: Precautions for Replacement of the Front Block Assy Ser-
vice
As Front Block Assy Service may be damaged by static
electricity from its structure, handle it carefully like for the
MOS IC.
electricity from its structure, handle it carefully like for the
MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
dusts nor exposed to strong light.
Note 4: フロントブロックAssy サービス交換時の注意
フロントブロックAssy サービスは構造上,静電気により破壊
される恐れがあるため,MOS ICと同様に注意して取り扱って
される恐れがあるため,MOS ICと同様に注意して取り扱って
ください。
また,受光部にはゴミの付着,および強い光がはいることの
ないように注意してください。
ないように注意してください。
Part
No.
Description
* 4-185-999-51 IM WASHER (C), ADJUST (t = 0.3)
* 4-185-999-61 IM WASHER (C), ADJUST (t = 0.35)
* 4-185-999-71 IM WASHER (C), ADJUST (t = 0.4)
* 4-185-999-81 IM WASHER (C), ADJUST (t = 0.45)
* 4-185-999-91 IM WASHER (C), ADJUST (t = 0.495)
* 4-185-999-61 IM WASHER (C), ADJUST (t = 0.35)
* 4-185-999-71 IM WASHER (C), ADJUST (t = 0.4)
* 4-185-999-81 IM WASHER (C), ADJUST (t = 0.45)
* 4-185-999-91 IM WASHER (C), ADJUST (t = 0.495)
Click on the first or last page to see other ILCE-7 / ILCE-7K / ILCE-7R (serv.man2) service manuals if exist.