DOWNLOAD Sony DSLR-A450 / DSLR-A450L / DSLR-A450Y Service Manual ↓ Size: 7.08 MB | Pages: 25 in PDF or view online for FREE

DSLR-A450/A450L/A450Y_L2

3-7E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-
6082-635-A).

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohl.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Set a camera to a cleaning mode.
3.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

4.  Repeat “3” several times to clean up.
5.  According to service manual, check if there is dirt on the CCD.

1 Souse the cleaning
 

cloth in ethyl alcohol.

2 The dry cleaning cloth.

OLPF

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310

DSLR-A450/A450L/A450Y_L2

3-7E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-
6082-635-A).

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohl.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Set a camera to a cleaning mode.
3.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

4.  Repeat “3” several times to clean up.
5.  According to service manual, check if there is dirt on the CCD.

1 Souse the cleaning
 

cloth in ethyl alcohol.

2 The dry cleaning cloth.

OLPF

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310

DSLR-A450/A450L/A450Y_L2

3-7E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-
6082-635-A).

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohl.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Set a camera to a cleaning mode.
3.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

4.  Repeat “3” several times to clean up.
5.  According to service manual, check if there is dirt on the CCD.

1 Souse the cleaning
 

cloth in ethyl alcohol.

2 The dry cleaning cloth.

OLPF

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310

DSLR-A450/A450L/A450Y_L2

3-7E

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-
6082-635-A).

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohl.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Set a camera to a cleaning mode.
3.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

4.  Repeat “3” several times to clean up.
5.  According to service manual, check if there is dirt on the CCD.

1 Souse the cleaning
 

cloth in ethyl alcohol.

2 The dry cleaning cloth.

OLPF

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310