Sony DSLR-A450 / DSLR-A450L / DSLR-A450Y Service Manual ▷ View online
DSLR-A450/A450L/A450Y_L2
Sony EMCS Co.
SERVICE MANUAL
Revision History
SERVICE NOTE (Check the following note before the service.)
LEVEL
2
Ver.
Date
History
Contents
985276231.pdf
2009L0500-1
© 2009.12
Published by Tokai TEC
Ver. 1.0 2009.12
DIGITAL SINGLE LENS REFLEX CAMERA/ZOOM LENS KIT
The components identified
by mark or dotted line with
mark are critical for safety.
Replace only with part number
specified.
by mark or dotted line with
mark are critical for safety.
Replace only with part number
specified.
DSLR-A450/A450L/A450Y
AEP Model
UK Model
E Model
Chinese Model
Korea Model
1-1. METHOD OF EXCHANGING SI SCREEN AND FOCUS PLATE
—
Official Release
2009.12
1.0
9-852-762-31
[About the service of this model]
DSLR-A450L is a commodity that packed the Digital Single Lens Reflex Camera (DSLR-A450) and Zoom Lens Kit (DT 18-55mm F3.5-5.6 SAM).
DSLR-A450Y is a commodity that packed the Digital Single Lens Reflex Camera (DSLR-A450) and W Zoom Lens Kit (DT 18-55mm F3.5-5.6
SAM/DT 55-200mm F4-5.6 SAM).
Refer to each following service manual the zoom lends kit, when you repair.
• Zoom Lens Kit
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM) Service Manual (9-852-691-1
DSLR-A450Y is a commodity that packed the Digital Single Lens Reflex Camera (DSLR-A450) and W Zoom Lens Kit (DT 18-55mm F3.5-5.6
SAM/DT 55-200mm F4-5.6 SAM).
Refer to each following service manual the zoom lends kit, when you repair.
• Zoom Lens Kit
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM) Service Manual (9-852-691-1
[])
SAL55200-2 (DT 4-5.6/55-200 SAM) (DT 55-200mm F4-5.6 SAM) Service Manual (9-852-692-1
[])
(SAL55200-2)
(SAL1855)
DSLR-A450/A450L/A450Y_L2
– 2 –
SPECIFICATIONS
Camera
[System]
Camera Type
Digital Single Lens Reflex
Camera with built-in flash
and interchangeable lenses
Camera with built-in flash
and interchangeable lenses
Lens
All of
α Lenses
[Image sensor]
Image format
23.4×15.6 mm (APS-C
format) CMOS image
sensor
format) CMOS image
sensor
Total pixel number of image sensor
Approx. 14 600 000 pixels
Effective pixel number of camera
Approx. 14 200 000 pixels
[SteadyShot]
System
Image sensor-shift
mechanism
mechanism
[Anti-Dust]
System
Charge protection coating
on Low-Pass Filter and
image sensor-shift
mechanism
on Low-Pass Filter and
image sensor-shift
mechanism
[Auto Focus System]
System
TTL phase-detection
system, CCD line sensors
(9 points, 8 lines with
center cross-hair sensor)
system, CCD line sensors
(9 points, 8 lines with
center cross-hair sensor)
Sensitivity Range
0 to 18 EV (at ISO 100
conversion)
conversion)
AF illuminator
Approx. 1 to 5 m (3.3 to
16.4 feet)
16.4 feet)
[Manual focus check Live View]
Image format
Image sensor for shooting
Frame Coverge
100%
[Built-In-Flash]
Flash guide number
GN 12 (in meters at ISO
100 conversion)
100 conversion)
Recycling time
Approx. 4 seconds
Flash coverage
Covering 18 mm lens
(focal length that the lens
indicates)
(focal length that the lens
indicates)
Flash compensation
±2.0 EV (1/3 EV step)
[Recording media]
“Memory Stick PRO Duo”
media, “Memory Stick
PRO-HG Duo” media, SD
memory card, SDHC
memory card
media, “Memory Stick
PRO-HG Duo” media, SD
memory card, SDHC
memory card
[LCD monitor]
LCD panel 6.7 cm (2.7 type) TFT
drive
230 400 (960 × 240) dots
Total number of dots
[Input/output terminals]
USB
miniB
HDMI
HDMI type C minijack
[Power, general]
Used battery pack
Rechargeable battery pack
NP-FM500H
NP-FM500H
[Others]
PictBridge
Compatible
Exif Print
Compatible
PRINT Image Matching III
Compatible
Dimensions Approx. 137 × 104 ×
81 mm (5 1/2 × 4 1/8 ×
3 1/4 inches) (W/H/D,
excluding protrusions)
3 1/4 inches) (W/H/D,
excluding protrusions)
Mass
Approx. 520 g (1 lb 2.3 oz)
(without batteries, memory
card and body accessories)
(without batteries, memory
card and body accessories)
Operating temperature
0 to 40°C (32 to 104°F)
File format JPEG (DCF Ver. 2.0, Exif
Ver. 2.21, MPF Baseline)
compliant, DPOF
compatible
compliant, DPOF
compatible
USB communication
Hi-Speed USB (USB 2.0
compliant)
compliant)
BC-VM10 Battery charger
Input rating 100 V – 240 V AC, 50/60
Hz, 9 W
Output rating
8.4 V DC, 0.75 A
Operating temperature range
0 to 40°C (32 to 104°F)
Storage temperature range
–20 to +60°C (–4 to
+140°F)
+140°F)
Maximum dimensions
Approx. 70 × 25 × 95 mm
(2 7/8 × 1× 3 3/4 inches)
(W/H/D)
(2 7/8 × 1× 3 3/4 inches)
(W/H/D)
Mass
Approx. 90 g (3.2 oz)
Rechargeable battery pack
NP-FM500H
NP-FM500H
Used battery
Lithium-ion battery
Maximum voltage
DC 8.4 V
Nominal voltage
DC 7.2 V
Maximum charge current
2.0 A
Maximum charge voltage
DC 8.4 V
Capacity
Typical
11.8 Wh (1 650 mAh)
Minimum 11.5 Wh (1 600 mAh)
Maximum dimensions
Approx. 38.2 × 20.5 × 55.6
mm (1 9/16 × 13/16 × 2 1/4
inches) (W/H/D)
mm (1 9/16 × 13/16 × 2 1/4
inches) (W/H/D)
Mass
Approx. 78 g (2.8 oz)
Design and specifications are subject
to change without notice.
to change without notice.
Eye Point Approximately 16. 5 mm
from the eyepiece,
10.9 mm from the eyepiece
frame at –1 m
10.9 mm from the eyepiece
frame at –1 m
–1
Dioptor Adjustment
–2.5 to +1.0 m
–1
[Exposure control]
Metering Cell
SPC
Metering method
40-segment honeycomb-
pattern
pattern
Metering Range
1 to 20 EV (3 to 20 EV
with Spot metering), (at
ISO 100 conversion with
F1.4 lens)
with Spot metering), (at
ISO 100 conversion with
F1.4 lens)
ISO sensitivity (Recommended
exposure index)
AUTO, ISO 200 to 12800
AUTO, ISO 200 to 12800
Exposure compensation
±2.0 EV (1/3 EV step)
[Shutter]
Type
Electronically-controlled,
vertical-traverse, focal-
plane type
vertical-traverse, focal-
plane type
Speed range 1/4000 second to 30
seconds, bulb, (1/3 EV
step)
step)
Flash sync speed
1/160 second
[Viewfinder]
Type
Fixed eye-level penta-
Dach-mirror
Dach-mirror
Frame Coverage
95%
Magnification
0.83 × with 50 mm lens at
infinity, –1 m
infinity, –1 m
–1
(diopter)
This specifications is extracted from
instruction manual of DSLR-A450.
instruction manual of DSLR-A450.
Model information table
• Abbreviation
AR :
AR :
Argentine
model
AUS :
Australian
model
BR
: Brazilian model
CH
: Chinese model
CND : Canadian model
EE
EE
: East European model
HK
: Hong Kong model
J
: Japanese model
JE :
Tourist
model
KR
: Korea model
NE
: North European model
TH :
Thai
model
Model
DSLR-A450
DSLR-A450L
DSLR-A450Y
Destination
AEP, UK, E, CH, KR
AEP, UK, E, CH, KR
AEP, UK, E, KR
DSLR-A450/A450L/A450Y_L2
– 3 –
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK OR DOTTED LINE WITH
MARK ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
MARK ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
CHEMICALS
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health
and environment, and wastes resources.
Manage the chemicals carefully as follows.
Their evaporation caused by improper management affects your health
and environment, and wastes resources.
Manage the chemicals carefully as follows.
•
Store chemicals sealed in a specific place to prevent from exposure
to high temperature or direct sunlight.
to high temperature or direct sunlight.
•
Avoid dividing chemicals into excessive numbers of small containers
to reduce natural evaporation.
to reduce natural evaporation.
•
Keep containers sealed to avoid natural evaporation when chemicals
are not in use.
are not in use.
•
Avoid using chemicals as much as possible. When using chemicals,
divide only required amount to a small plate from the container and
use up it.
divide only required amount to a small plate from the container and
use up it.
EXTERIOR PARTS
Be careful to the following points for plastic parts used in this unit.
•
Use a piece of cleaning paper or cleaning cloth for cleaning plastic
parts. Avoid using chemicals.
parts. Avoid using chemicals.
Even if you have to use chemicals to clean heavy dirt, don’t use paint
thinner, ketone, nor alcohol.
thinner, ketone, nor alcohol.
• Insert the specific screws vertically to the part when installing a
plastic part.
Be careful not to tighten screws too much.
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
•
Set the soldering iron tip temperature to 350 °C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
•
Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
bridges.
2. Check the interboard wiring to ensure that no wires are “pinched”
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 °C during
repairing.
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
DSLR-A450/A450L/A450Y_L2
1-1E
1. SERVICE NOTE
– ENGLISH –
1-1. METHOD OF EXCHANGING FOCUS PLATE
– JAPANESE –
1-1. 焦点板の交換方法
2
Remove VM FS retainer.
1
Remove two claws pushing part A below,
and remove VM FS retainer in the direction
of arrow.
and remove VM FS retainer in the direction
of arrow.
4
Remove SI screen.
3
Remove focus plate and VB spacer.
Focus Plate
SI Screen
Note: When you exchange the SI screen,
don't put dust or give a scratch.
VB Spacer
VM FS Retainer
VM FS Retainer
Claw
Claw
Claw
A
1
A部を下に押してつめ2箇所を外し,
矢印方向にVM FSリテーナを外す。
2
VM FSリテーナを外す。
4
SIスクリーンを外す。
3
焦点板とVBスペーサを外す。
焦点板
SIスクリーン
注意: SIスクリーン交換時は,SIスクリーンに埃や
傷を付けないように注意してください。
VBスペーサ
VM FSリテーナ
VM FSリテーナ
つめ
つめ
つめ
A