DOWNLOAD Sony DSLR-A230 / DSLR-A330 / DSLR-A380 Service Manual ↓ Size: 7.73 MB | Pages: 31 in PDF or view online for FREE

DSLR-A230/A330/A380_L2

3-7

ON

OFF

#5: M1.7 X 3.5 (Tapping)

(Black)
3-080-204-01

3.5

1.7

#5: M1.7 X 3.5 (Tapping)

(Black)
3-080-204-01

3.5

1.7

#5: M1.7 X 3.5 (Tapping)

(Black)
3-080-204-01

3.5

1.7

Assembly-7: Flash Unit Harness

Assembly-9: Flash Unit Harness, DC Jack Harness

DC Jack Harness

Flash Unit Harness

Assembly-10: Shoulder Cover G Assy

Shoulder Cover G Assy

Assembly-8: Front Cover

Front Cover

Confirm the position of the focus mode switch.

Rib

Rib

Rib

- Front View -

- Right View -

Confirm the position of the
power switch.

Confirm the position of the
LIVE VIEW/OVF switch.

Control Switch Block

Screw

Screw (A330/A380)

6-17. ST Plunger Cover

6-18. Connector 2P Housing

ST Plunger Cover

Boss

Boss

Connector 2P Housing
(Yellow)

∗ Note the direction.

Connector 2P Housing
(Red)

∗ Note the direction.

Pink

Black

Screw

Rib

Rib

White

DSLR-A230/A330/A380_L2

3-8

<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.

Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 

The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-
6082-635-A).

CCD Cleaning Jig (New)
(J-6082-663-A)

CCD Cleaning Jig

CCD Cleaning Jig (Tip)

Protection Sheet

<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 

1

 Souse the one cleaning cloth in ethyl alcohl.

 

2

 Put the other cleaning cloth on a tray as it is dry.

2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 

* Do not slide the tip from right to left or up and down while dabbing.

3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 

* Do not slide from right to left or up and down while dabbing.

4.  Wait until the tip will be dried completely.

<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Set a camera to a cleaning mode.
3.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 

* Do not slide from right to left or up and down while dabbing.

4.  Repeat “3” several times to clean up.
5.  According to service manual, check if there is dirt on the CCD.

1

Souse the cleaning
cloth in ethyl alcohol.

2

The dry cleaning cloth.

OLPF

Cleaning Jig
(J-6082-635-A)

Cleaning Cloth
(J-6082-636-A)

Cut

EE3310

DSLR-A230/A330/A380_L2

3-9E

Note: Confirm it is the same before the following item cleans it after 

cleaning the viewfinder.
1. Digital zoom check
2. Inclination of Live view image
3. Resolution of Live view image in surrounding

1

3

4

2

2

Remove the connection of four flexible board.

1

Remove the JS Spacer.

JS Spacer

Screw

4

Remove the diopter adjust cam cover and the
diopter adjust click plate after removing one screw.
Note: Removed parts are not supplied.

Please recycle.

Diopter Adjust
Click Plate

Diopter Adjust Cam Cover

Screw

3

Pull out four bosses from AE-034 flexible board.

AE-034 flexible board

Boss

Boss

- Top View -

- Top View -

- Back View -

Beam Splitter Block

Screw

6

Clean dust with the blower.

Blower

Caution: Never touch two screws.

5

Remove the beam splitter block after removing
three screws.
Note: Removed parts are not supplied.

Please recycle.

DSLR-A230/A330/A380_L2

3-9E

Note: Confirm it is the same before the following item cleans it after 

cleaning the viewfinder.
1. Digital zoom check
2. Inclination of Live view image
3. Resolution of Live view image in surrounding

1

3

4

2

2

Remove the connection of four flexible board.

1

Remove the JS Spacer.

JS Spacer

Screw

4

Remove the diopter adjust cam cover and the
diopter adjust click plate after removing one screw.
Note: Removed parts are not supplied.

Please recycle.

Diopter Adjust
Click Plate

Diopter Adjust Cam Cover

Screw

3

Pull out four bosses from AE-034 flexible board.

AE-034 flexible board

Boss

Boss

- Top View -

- Top View -

- Back View -

Beam Splitter Block

Screw

6

Clean dust with the blower.

Blower

Caution: Never touch two screws.

5

Remove the beam splitter block after removing
three screws.
Note: Removed parts are not supplied.

Please recycle.