Sony DSLR-A200H (serv.man2) Service Manual ▷ View online
2-1
SAL18200 (3.5-6.3/18-200) (DT 18-200mm F3.5-6.3)
2. DISASSEMBLY
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.
assembling the lens, Use the universal wrench.
How to Use
Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:
For the notches: chip-A
For the holes:
chip-B
Match the universal wrench to the holes or notches of the lens block, etc.
When top of tip does not reach holes or notches because the fixed screw becomes obstructive,
replace the fixed screw to below.
+B 3X5 7-682-546-09
replace the fixed screw to below.
+B 3X5 7-682-546-09
Notches
Holes
Universal wrench
J-6082-609-A
J-6082-609-A
Chip-A for
universal wrench:
J-6082-609-1
universal wrench:
J-6082-609-1
Chip-B for
universal wrench:
J-6082-609-2
universal wrench:
J-6082-609-2
Ver 1.2 2007.02
Notches
Chip-A
Chip-A
Chip-B
Chip-B
Chip
Fixed screw
Fixed screw
Chip
Match the universal wrench
to the width of holes or notches.
to the width of holes or notches.
Universal wrench
Holes
2-2
SAL18200 (3.5-6.3/18-200) (DT 18-200mm F3.5-6.3)
2-1.
DISASSEMBLY
2-1-1. 1ST LENS BARREL ASSEMBLY, MOUNT ASSEMBLY AND
ZOOM BAYONET ASSEMBLY
Note: For more detail procedure, see page 2-3.
D
C
C
A
B
B
A
D
2
Filter Screw Frame
3
1st Lens Barrel Assembly
1
Rubber Ring
4
Light
5
2nd Lens Rubber Ring
6
2nd Lens Barrel Assembly
7
2nd Lens Adjustment Washer
8
Rear Light
9
Mount Assembly
Joint Coma
0
Back Adjustment Washer
!-
Main PCB
!=
Rear Lens Barrel
![
Zoom Bayonet
!]
Focus Brush
!\
Focus Ring
!;
Zoom Brush
HELP01
HELP02
HELP03
HELP03
HELP04
EXPLODED VIEW
HELP05
HELP03
HELP06
HELP07
HELP08
EXPLODED VIEW
Brush Adjustment
Washer
Washer
Assembly
Assembly
Assembly
Assembly
Shield Barrel
Shield Plate
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
FLANGE BACK ADJUSTMENT
FOCUS-SHIFT ADJUSTMENT
ZOOM BRUSH
POSITION ADJUSTMENT
POSITION ADJUSTMENT
FOCUS BRUSH
POSITION ADJUSTMENT
POSITION ADJUSTMENT
APERTURE
DIAMETER
ADJUSTMENT
DIAMETER
ADJUSTMENT
(See Page 2-4.)
Ver. 1.6 2008.06
The changed portions from
Ver. 1.5 are shown in blue.
Ver. 1.5 are shown in blue.
2-3
SAL18200 (3.5-6.3/18-200) (DT 18-200mm F3.5-6.3)
D
C
C
A
B
B
A
D
2
2
-1
2
-2
2
-3
3
3
-1
6
-1
6
-2
3
-2
3
-3
1
4
5
6
7
8
9
0
!-
!=
![
!]
!\
6
-3
8
-1
9
-1
!-
-1
!]
-1
!=
-1
!=
-2
!=
-3
!=
-4
![
-6
![
-1
!\
-1
!;
-2
!\
-2
![
-7
!\
-5
![
-5
![
-2
![
-3
![
-4
!-
-2
8
-4
8
-3
9
-3
8
-2
9
-2
8
-5
8
-6
9
-4
0
-1
!\
-3
!\
-4
!;
!;
-1
2-4
SAL18200 (3.5-6.3/18-200) (DT 18-200mm F3.5-6.3)
2-1-2. 3RD LENS BARREL/DIAPAGM ASSEMBLY
Note: For more detail procedure, see page 2-5.
J
I
I
F
F
J
J'
I'
C
C
D
G
E
E'
E
G
H
H
D
B
B
A
A
EXPLODED VIEW
EXPLODED VIEW
4th Lens
Adjustment
Washer
Adjustment
Washer
G10-11
Adjustment
Washer
Adjustment
Washer
1
Outside Barrel
2
1st Lens Slip Barrel
HELP13
HELP12
HELP10
3
Length Groove
4
Move Light
HELP11
5
4th Lens Barrel Assembly
6
3rd Lens Barrel/Diaphragm
Assembly
7
First Cam Barrel
8
Linear-Drive Barrel
HELP09
FOCUS-SHIFT
ADJUSTMENT (APERTURE)
ADJUSTMENT (APERTURE)
FLANGE BACK CHECK
Shield Barrel
Barrel Assembly
Assembly
Click on the first or last page to see other DSLR-A200H (serv.man2) service manuals if exist.