Sony DSC-WX50 (serv.man2) Service Manual ▷ View online
DSC-WX50_L2
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
Link
ACCESSORIES
DISCHARGING OF THE CHARGING CAPACITOR
ASSEMBLY
3
Panel Module
4
Front Block Assy
1
2
Rear Block Assy
q;
BTH Block Assy
SY-311/SY-321 Board
ST-269 Flexible Board
Release Assy
8
Lens Block Section
5
Main Frame Assy
Control Switch Block
(SW63150)
(SW63150)
• CD-811 Flexible Board
9
7
6
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original
• -XX, -X mean standardized parts, so they may have some differences from the original
one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not sup-
plied.
• Due to standardization, replacements in the parts list may be different from the parts
specified in the diagrams or the components used on the set.
• CAPACITORS:
uF:
uF:
μF
• COILS
uH:
uH:
μH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
nonflammable
• SEMICONDUCTORS
In each case, u: μ, for example:
uA...:
In each case, u: μ, for example:
uA...:
μA... , uPA... , μPA... ,
uPB...
,
μPB... , μPC... , μPC... ,
uPD...,
μPD...
The components identified by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
le numéro spécifié.
• Color Indication of Appearance Parts
Example:
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は, 補修用部品であるため, 回路図及び
セットに付いている部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
• *印の部品は常備在庫しておりません。
セットに付いている部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
• *印の部品は常備在庫しておりません。
• 抵抗の単位Ωは省略してあります。
金 被:金属被膜抵抗。
サンキン:酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。
金 被:金属被膜抵抗。
サンキン:酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。
0印の部品,または0印付の点線で囲ま
れた部品は,安全性を維持するために,
重要な部品です。
従って交換時は,必ず指定の部品を使用
してください。
れた部品は,安全性を維持するために,
重要な部品です。
従って交換時は,必ず指定の部品を使用
してください。
• 外装部品色表示
例:
(SILVER) :セットの色を表す。
(Silver) :部品の色を表す。
• Abbreviation
AUS :
AUS :
Australian
model
BR
: Brazilian model
CH
: Chinese model
CND : Canadian model
HK
HK
: Hong Kong model
J
: Japanese model
JE :
Tourist
model
KR
: Korea model
TW :
Taiwan
model
View Position
Right View
Front View
Bottom View
Back View
Left View
Top View
DSC-WX50_L2
2-2
– ENGLISH –
– JAPANESE –
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked
of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, don’t press down at wire of con-
nector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE CHARGING CAPACITOR (C901)
The charging capacitor is charged up to the maximum 330 V
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω/1 W
Wrap insulating tape.
1 k
Ω/1 W
Wrap insulating tape.
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け,
折れ等がないことを確認する。
また,コネクタへの接続は,差し込み不足や斜め差しになら
ないように注意する。
• コネクタを取り外す時に,線材部(極細)を持って引っ張ると
断線する恐れがありますので,絶対に線材部(極細)を持って
引っ張らないでください。
引っ張らないでください。
• 線材部(極細)を押さえながらコネクタを差し込むと,線材部
(極細)が断線する恐れがありますので,絶対に線材部(極細)
には負担をかけないでください。
• 金メッキされているフレキシブル基板には,強い負担をかけ
ないでください。
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
ストロボ用充電コンデンサ(C901)の放電
ストロボ用充電コンデンサは最大330Vの電圧で充電され
ています。
この高電圧で充電されたコンデンサに手を触れた場合,
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
ています。
この高電圧で充電されたコンデンサに手を触れた場合,
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
ショート治具の準備
ショート治具は1kΩ/1W抵抗(1-215-869-11)の両端に
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
ST-269 Flexible
Board
Board
ST-269 Flexible
Board
Board
C901
R:1 k
Ω/1 W
ㇱຠࠦ࠼㧦
1-215-869-11
ࠦࡦ࠺ࡦࠨߩ㔚
ࡈ࠶ࠪࡘ࡙࠾࠶࠻ߩ㔚Ḯࠦࡦ࠺ࡦࠨ
ߩ┵ሶ㑆ࠍ࡚ࠪ࠻ᴦౕߢ⚂⑽㑆
ធ⛯ߔࠆޕ
ࡈ࠶ࠪࡘ࡙࠾࠶࠻ߩ㔚Ḯࠦࡦ࠺ࡦࠨ
ߩ┵ሶ㑆ࠍ࡚ࠪ࠻ᴦౕߢ⚂⑽㑆
ធ⛯ߔࠆޕ
C901
ST-269 Flexible
Board
Board
ST-269 Flexible
Board
Board
C901
R:1 k
Ω/1 W
C901
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.
Short-circuit between two points with
the short jig about 10 seconds.
(Part code: 1-215-869-11)
DSC-WX50_L2
2-3
2-1. EXPLODED VIEWS
2-1-1. REAR SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1. Remove to numerical order (
1
to
5
) in the left figure.
DISASSEMBLY
1
Ref. No. 9/Ref. No. 10 X 2
→ Open the HDMI Lid (
1
)
→ Ref. No. 9/Ref. No. 10 X 3 → #237/#245 X 2
#237
#245
(Note 1)
4
LCD901
1
8
5
2
3
6
2
7
5
(Note 2)
4
(Note 2)
1
3
(Claw)
(Claw)
(Claw)
(Claws)
(Boss)
(Claw)
(Boss)
9
10
(Note 1)
9
10
(Note 1)
9
10
(Note 1)
(Note 2)
Top Section
(See Page 2-4)
When assembling,
adjust the position.
adjust the position.
1
11
Ref.No.9
Ref.No.10
Ref.No.9
Ref.No.10
#237
#245
Bottom View
Left View
Right View
1
Screw
Note
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
Cabinet's Color
Table 2-1
Note 1
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
Ref.No.10 (Silver)
Ref.No.9 (Black)
#237 (Silver)
#245 (Black)
SILVER/BLUE/
GOLD/PINK
GOLD/PINK
BLACK
SILVER/BLUE/
GOLD/PINK
GOLD/PINK
BLACK
#237:
M1.4 X 2.0
(Silver)
4-270-114-21
(Silver)
4-270-114-21
2.0
1.4
#245:
M1.4 X 2.0
(Black)
4-412-769-31
(Black)
4-412-769-31
2.0
1.4
Note 2: Refer to “Assembly-3: Installation Cautions of the LCD Cushion
(150) and LCD Window (150).”.
Note 2: “Assembly-3: Installation Cautions of the LCD Cushion (150)
and LCD Window (150).” を参照してください。
1
4-411-659-01 GASKET
(F)
2
A-1852-919-A FRONT (150) SILVER BLOCK ASSY (SILVER)
2
A-1852-920-A FRONT (150) BLACK BLOCK ASSY (BLACK)
2
A-1852-921-A FRONT (150) PINK BLOCK ASSY (PINK)
2
A-1852-922-A FRONT (150) GOLD BLOCK ASSY (GOLD)
2
A-1852-923-A FRONT (150) BLUE BLOCK ASSY (BLUE)
3
A-1852-924-A COVER (150) SILVER BLOCK ASSY (SILVER)
3
A-1852-925-A COVER (150) BLACK BLOCK ASSY (BLACK)
3
A-1852-926-A COVER (150) PINK BLOCK ASSY (PINK)
3
A-1852-927-A COVER (150) GOLD BLOCK ASSY (GOLD)
3
A-1852-928-A COVER (150) BLUE BLOCK ASSY (BLUE)
4
4-411-648-01
CUSHION (150), LCD (Note 2)
5
4-411-647-01
WINDOW (150), LCD (Note 2)
6
1-490-033-11
SWITCH BLOCK, CONTROL (SW63150) (SILVER)
6
1-490-033-21
SWITCH BLOCK, CONTROL (SW63150) (BLACK)
6
1-490-033-31
SWITCH BLOCK, CONTROL (SW63150) (PINK)
6
1-490-033-41
SWITCH BLOCK, CONTROL (SW63150) (GOLD)
6
1-490-033-51
SWITCH BLOCK, CONTROL (SW63150) (BLUE)
7
4-411-640-01
COVER (150), DC (SILVER)
7
4-411-640-11
COVER (150), DC (BLACK)
7
4-411-640-21
COVER (150), DC (PINK)
7
4-411-640-31
COVER (150), DC (GOLD)
7
4-411-640-41
COVER (150), DC (BLUE)
8
X-2583-255-1 CABINET REAR 150 SILVER ASSY (SILVER)
8
X-2583-256-1 CABINET REAR 150 BLACK ASSY (BLACK)
8
X-2583-257-1 CABINET REAR 150 PINK ASSY (PINK)
8
X-2583-258-1 CABINET REAR 150 GOLD ASSY (GOLD)
8
X-2583-259-1 CABINET REAR 150 BLUE ASSY (BLUE)
9
4-424-201-01
SCREW (M1.4), NEW TRU-STAR, P2 EG (M1.4 X 3.0)
(Note 1)
10
4-424-250-01
SCREW (M1.4), NEW TRU-STAR, P2 (M1.4 X 3.0)
(Note 1)
11
A-1889-550-A WINDOW BLOCK ASSY (SERVICE)
LCD901 1-811-497-11
PANEL MODULE (PE3-ACM) (Note 2)
#237
4-270-114-21
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
#245
4-412-769-31
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
Ver. 1.3 2012.04
DSC-WX50_L2
2-4
2-1-2. TOP SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1. Remove to numerical order (
1
to
4
) in the left figure.
DISASSEMBLY
1
61
2
51
4
55
62
63
60
59
56
57
58
2
1
54
53
52
#71
ns
C901
(Claw)
(Boss)
(Boss)
(Boss)
(Claw)
(Claws)
(Claws)
(Claw)
Main Section
(See Page 2-5)
4
-2
4
-1
(Note 1)
3
(Note 2, 3)
(Note 3)
Note
Screw
#71: M1.4 X 2.0
(Red)
3-208-537-01
3-208-537-01
2.0
1.4
3
#71
Back View
DISCHARGING OF THE CHARGING CAPACITOR
ストロボ用充電コンデンサの放電
Note 1: Refer to “Assembly-2: Precaution During of ST-269
Flexible Board.”.
Note 2: When removing the Radiation Sheet (150), be careful not
to break the flexible board of the Lens Unit.
Note 1: “Assembly-2: Precaution During of ST-269 Flexible
Board.” を参照してください。
Note 2: Radiation Sheet (150) を剥がす際は、レンズユニットの
フレキを破損しないよう注意してください。
51
X-2583-250-1 RELEASE (150) SILVER ASSY (SILVER)
51
X-2583-251-1 RELEASE (150) BLACK ASSY (BLACK)
51
X-2583-252-1 RELEASE (150) PINK ASSY (PINK)
51
X-2583-253-1 RELEASE (150) GOLD ASSY (GOLD)
51
X-2583-254-1 RELEASE (150) BLUE ASSY (BLUE)
52
4-266-381-01
SHEET, CABINET UPPER (770)
53
4-411-649-01
RUBBER (150), MICROPHONE
54
4-409-867-01
ST SHEET (770)
55
A-1854-924-A ST-269 BOARD, COMPLETE (Note 1)
56
4-411-656-01
BASE (150), SHEET MICROPHONE
57
1-489-357-11
FLASH UNIT
58
4-411-658-01
SHEET (150), RADIATION (Note 2, 3)
59
4-411-650-01
SHEET (SY) (150) (Note 3)
60
4-411-653-01
CUSHION (SY) (150)
61
X-2583-260-1 FRAME (150) ASSY, MAIN
62
4-411-657-01
SHEET (LCD) (150), RADIATION
63
4-411-654-01 SHEET
(MF)
C901
1-118-015-11
ALUMINIUM ELECT 53uF 330V
#71
3-208-537-01
0+Z M1.4X2 NEW TORASUTA
ns : not supplied
1
#71
4
Cabinet Upper Sheet (770) (
4
-1
)
→ ST Sheet (770) (
4
-2
)
Note 3: The Sheet (SY) (150) and Radiation Sheet (150) when
peeling off once, so that it cannot be reused.
Note 3: Sheet (SY) (150) とRadiation Sheet (150) は一度剥がす
と粘着力が弱くなるため、再利用はしないでください。
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
Ver. 1.3 2012.04
Click on the first or last page to see other DSC-WX50 (serv.man2) service manuals if exist.