Sony DSC-WX50 (serv.man2) Service Manual ▷ View online
DSC-WX50_L2
1-10
1-7.
ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD
A
下図は当機種と本体の形状が異なります。
Note:
Note:
As for the figure below, this model and the shape
of the main body are different.
of the main body are different.
Barrier Assy
Claws
Claws
Hole
Barrier Assy
Claws
Claws
Barrier
Lever
3
4
Installation
1
1
2
5
Removal
1
1
2
3
4
Barrier Tape
Dent
Ornamental Ring A
Barrier Assy
Barrier Tapes
Barrier Tape
Barrier Tape
Ornamental Ring A
Solvent
Tweezers
Disengage the four claws and remove the Barrier Assy.
Fit the four claws while inserting the Barrier Lever into the hole and attach the Barrier Assy.
Affix two Barrier Tapes to the Barrier Assy so that the end of each Barrier Tape touches the dent.
Note: The Barrier Tapes must not be wrinkled.
Affix two Barrier Tapes to the Barrier Assy so that the end of each Barrier Tape touches the dent.
Note: The Barrier Tapes must not be wrinkled.
Peel off the release papers of the Barrier Tapes.
Install the Ornamental Ring A and press it lightly.
Install the Ornamental Ring A and press it lightly.
Turn on the power switch and extend the lens (WIDE end).
Detach the battery.
Apply alcohol to two gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below.
Turn the Ornamental Ring A clockwise and counterclockwise to detach it.
Detach the battery.
Apply alcohol to two gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below.
Turn the Ornamental Ring A clockwise and counterclockwise to detach it.
1-8.
OPTICAL STEPPING MOTOR (F1430) REPLACING METHOD
Removal
1
1
2
Screw
Optical Stepping
Motor (F1430)
Motor (F1430)
Solders
Install
1
1
2
Screw
Optical Stepping
Motor (F1430)
Motor (F1430)
Groove
Projection
of worm
of worm
Solders
Remove the screw.
Unsolder the four locations of the Optical Stepping Motor (F1430) to detach it.
Unsolder the four locations of the Optical Stepping Motor (F1430) to detach it.
Solder the four locations of the Optical Stepping Motor (F1430).
Install the Optical Stepping Motor (F1430) with a screw.
*Tightening torque = 0.0xx
Install the Optical Stepping Motor (F1430) with a screw.
*Tightening torque = 0.0xx
± 0.0xN • m (0.x ± 0.xkgf • cm)
Note:
Install the Optical Stepping Motor (F1430) while fitting the groove with the projection of worm.
Install the Optical Stepping Motor (F1430) while fitting the groove with the projection of worm.
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2012.03
DSC-WX50_L2
1-11
1-9.
DC MOTOR WORM (A) BLOCK ASSY REPLACING METHOD
5
6
7
Removal
1
2
3
4
Remove the Rear Mirror Plate.
Remove the Gear B (Black) and the Gear A (White).
Remove the two screws, and remove soldering from the two points, and then remove the DC Motor (A) Block Assy.
Remove the Gear B (Black) and the Gear A (White).
Remove the two screws, and remove soldering from the two points, and then remove the DC Motor (A) Block Assy.
Claws
Screws
Screws
Rear Mirror
Plate
DC Motor Worm
(A) Block Assy
Solders
Screws
Gear B
(Black)
Gear A
(White)
Sensor
Sensor
Claw
Boss
Rib
Rib
Claw
Disconnect the Iris Flexible Board
from LF-115 Flexible Board.
from LF-115 Flexible Board.
Top View
FG Leaf
Spring
Boss
Claws
FPC Retainer
Back View
Rib
LF-115 Flexible Board
Disengage the two claws and remove the FG Leaf Spring.
Remove the two Sensors.
Disengage the three claws and remove the FPC Retainer.
Remove the two Sensors.
Disengage the three claws and remove the FPC Retainer.
Remove the LF-115 Flexible Board.
Installation
1
2
3
4
Solder the two locations.
Install the DC Motor Worm (A) Block Assy and secure it with two screws.
*Tightening torque = 0.0xx
Install the DC Motor Worm (A) Block Assy and secure it with two screws.
*Tightening torque = 0.0xx
± 0.0xN • m (0.x ± 0.xkgf • cm)
Install the Gear B (Black) and the Gear A (White).
Install the Rear Mirror Plate and secure it with two screws.
*Tightening torque = 0.0xx
Install the Rear Mirror Plate and secure it with two screws.
*Tightening torque = 0.0xx
± 0.0xN • m (0.x ± 0.xkgf • cm)
Install the LF-115 Flexible Board.
Install the FPC Retainer while fitting the three claws and the boss.
Install the two Sensors
Install the FG Leaf Spring while fitting the two claws..
Install the two Sensors
Install the FG Leaf Spring while fitting the two claws..
6
7
8
Claws
Sensor
Sensor
FG Leaf Spring
Boss
FPC Retainer
Claw
Boss
Rib
Rib
Claw
Disconnect the Iris Flexible Board
from LF-115 Flexible Board.
Top View
Back View
5
Screws
Screws
Rear Mirror Plate
DC Motor Worm
(A) Block Assy
Solders
Screws
Gear B
(Black)
Gear B
(Black)
Gear D
(Black)
Naruto
Gear
Gear A
(White)
Gear A
(White)
Gear C
(White)
Claws
Rib
LF-115 Flexible Board
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2012.03
DSC-WX50_L2
1-12
5
6
Removal
1
2
3
4
Claws
Sensor
Sensor
Claw
Boss
Rib
Rib
Rib
Claw
Disconnect the Iris Flexible Board
from LF-115 Flexible Board.
LF-115 Flexible Board
Top View
FG Leaf
Spring
Boss
Claws
FPC Retainer
Back View
Gear B
(Black)
Gear D
(Black)
Gear A
(White)
Gear C
(White)
Naruto
Gear
Screws
Rear Mirror
Plate
Screws
Disengage the two claws and remove the FG Leaf Spring.
Remove the two Sensors.
Disengage the three claws and remove the FPC Retainer.
Remove the two Sensors.
Disengage the three claws and remove the FPC Retainer.
Remove the LF-115 Flexible Board.
Remove the four screws to detach the Rear Mirror Plate
Remove the Gear B (Black), Gear A (White), Gear C (White), Gear D (Black), and Naruto Gear.
Remove the Gear B (Black), Gear A (White), Gear C (White), Gear D (Black), and Naruto Gear.
1-10.
TWO TUBE LUBRICATING BLOCK ASSY AND GROUP 1 FRAME REPLACING METHOD
7
8
9
Iris Flexible Board
Cutout
Main Assy (A)
Rotary Tube
Block Assy
3 Group Spring
3 Group Frame
Block Assy
Tube
Lubricating
q;
qa
Main Assy (B)
Tube Lubricating
Block Assy
Shield Ring (C)
Remove the 3 Group spring and remove the 3 Group Frame Block Assy..
Turn the Tube Lubricating to the TELE state and remove the Iris Flexible Board from the cutout.
Remove the Main Assy (A) in the WIDE state.
Remove the Main Assy (B).
Remove the Tube Lubricating Block Assy and the Shield Ring (C) from the Rotary Tube Block Assy.
Remove the Tube Lubricating Block Assy and the Shield Ring (C) from the Rotary Tube Block Assy.
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2012.03
DSC-WX50_L2
1-13
A
qs
qd
qf
qg
qh
qj
qk
Shield Ring (D)
1 Group Assy
Frame Block Assy (1430A)
Tube Lubricating
Block Assy
Shield Ring (AB)
Cam Tube
Block Assy
Barrier Assy
Claws
Claws
Ornamental
Ring A
Bond
Tweezers
Group 1 Frame
Group 1 Lens
Frame Assy
Solvent
Objective Side View
Remove the Shield Ring (D) and remove the Frame Block Assy (1430A).
Remove the 1 Group Assy.
Remove the Tube Lubricating Block Assy and the Shield Ring (AB) from the Cam Tube Block Assy.
Remove the Tube Lubricating Block Assy and the Shield Ring (AB) from the Cam Tube Block Assy.
Apply alcohol to two gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below.
Turn the Ornamental Ring A clockwise and counterclockwise to detach it.
Turn the Ornamental Ring A clockwise and counterclockwise to detach it.
Remove bond at two locations shown in the figure below and turn the Group 1 Lens Frame Assy.
Remove the Group 1 Lens Frame Assy from the Group 1 Frame.
Remove the Group 1 Lens Frame Assy from the Group 1 Frame.
Installation
1
2
3
Bond
Round mark
Round marks
4
5
6
7
Barrier Tape
Dent
Hole
Barrier
Lever
Barrier Assy
Claws
Claws
Barrier Assy
Barrier Tape
Barrier Tape
Ornamental
Ring A
Group 1 Frame
Group 1 Lens
Frame Assy
Barrier Tapes
Objective Side View
Objective Side View
Objective Side View
Install the Group 1 Lens Frame Assy to the Group 1 Frame.
Turn the Group 1 Lens Frame Assy so that the round mark comes to the position shown in the figure below.
Apply bond to the two points shown in the figure below.
Note: Use Super X bond or equivalent.
Turn the Group 1 Lens Frame Assy so that the round mark comes to the position shown in the figure below.
Apply bond to the two points shown in the figure below.
Note: Use Super X bond or equivalent.
Fit the four claws while inserting the Barrier Lever into the hole and attach the Barrier Assy.
Affix two Barrier Tapes to the Barrier Assy so that the end of each Barrier Tape touches the dent.
Note: The Barrier Tapes must not be wrinkled.
Affix two Barrier Tapes to the Barrier Assy so that the end of each Barrier Tape touches the dent.
Note: The Barrier Tapes must not be wrinkled.
Peel off the release papers of the Barrier Tapes.
Install the Ornamental Ring A and press it lightly.
Install the Ornamental Ring A and press it lightly.
Click on the first or last page to see other DSC-WX50 (serv.man2) service manuals if exist.