Sony DSC-WX350 Service Manual ▷ View online
DSC-WX350
4-8
4-4. LENS BLOCK
4-4-1. Removal and Installation
(1) Barrier Base Replacing Method
Removal
1. Turn on the power and pull out the lens to set it in the TELE end state.
2. Remove the battery.
3. Pour a solvent such as alcohol to two gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below.
4. Heat the Ornamental Ring A with a drier.
5. Repeat steps 3 and 4, and then remove the Ornamental Ring A.
1. Turn on the power and pull out the lens to set it in the TELE end state.
2. Remove the battery.
3. Pour a solvent such as alcohol to two gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below.
4. Heat the Ornamental Ring A with a drier.
5. Repeat steps 3 and 4, and then remove the Ornamental Ring A.
Ornamental Ring A
A
Tweezers
Drier
Solvent
6. Release the four claws to detach the Barrier Cover and the two Barrier Blade B, and then release one claw from each Torsion Spring to
detach the two Barrier Blade A.
Barrier Cover
Barrier Blade B
Barrier Blade A
Claws
Claws
Claw
7. Remove the two Torsion Springs and the Switching Ring Spring, and then release the two claws to detach the Barrier Base.
Barrier Base
Switching Ring Spring
Torsion Springs
Claws
DSC-WX350
4-9
Installation
1. Insert the two claws on the Barrier Base into the two holes to install the Barrier Base.
2. Install the two Torsion Springs.
3. Install the Switching Ring Spring while matching them with the bosses.
1. Insert the two claws on the Barrier Base into the two holes to install the Barrier Base.
2. Install the two Torsion Springs.
3. Install the Switching Ring Spring while matching them with the bosses.
Barrier Base
Switching Ring
Spring
Spring
Boss
Boss
Bosses
Torsion Springs
Torsion Spring
Rib
Boss
Hole
Claws
Holes
Claws
4. Install the two Barrier Blade A and the two Barrier Blade B.
Note: Hook the claw of the Barrier Blade A to the Torsion Spring.
5. Attach the Barrier Cover while matching it with the four claws.
Barrier Blade B
Barrier Blade A
Barrier Blade A
Boss
Torsion Spring
Torsion
Spring
Spring
Claws
Claw
Barrier Cover
Claws
Claw
6. Peel off the release papers of the Barrier Tapes and install the Ornamental Ring A.
Note: Insert the projection of the Ornamental Ring A to the cutout.
Ornamental Ring A
Projection
Cutout
Barrier Tapes
DSC-WX350
4-10
(2) Z Motor Assy Replacing Method
Removal
1. Remove the two screws and remove the Z Motor Assy.
1. Remove the two screws and remove the Z Motor Assy.
Screws
Z Motor Assy
2. Disengage the two claws and remove the FG Plate Spring.
3. Remove the two sensors.
4. Remove solders at two locations to detach the Z Motor Assy.
3. Remove the two sensors.
4. Remove solders at two locations to detach the Z Motor Assy.
.
Z Motor Assy
Solders
Z Motor Assy
FG Plate
Spring
Spring
Sensor
Sensor
Claws
Installation
1. Solder the Z Motor Assy at two locations.
2. Install the two Sensors.
3. Attach the FG Plate Spring.
1. Solder the Z Motor Assy at two locations.
2. Install the two Sensors.
3. Attach the FG Plate Spring.
Z Motor Assy
Solders
Z Motor Assy
FG Plate
Spring
Spring
Sensor
Sensor
Claws
4. Install the Z Motor Assy and install the two screws.
Screws
Z Motor Assy
DSC-WX350
4-11
(3) 2nd Cam Barrel Replacing Method
Removal
1. Remove the five screws.
1. Remove the five screws.
Screws
Screws
2. Remove the Z Motor Assy, peel off the adhesive part of the Main Flexible Assy, and then disconnect the Connector.
3. Remove the Naruto Gear.
3. Remove the Naruto Gear.
Main Flexible Assy
Z Motor Assy
Naruto Gear
Connector
4. Remove the Rear Lens Assy.
Rear Lens Assy
Click on the first or last page to see other DSC-WX350 service manuals if exist.