DOWNLOAD Sony DSC-WX220 Service Manual ↓ Size: 8.08 MB | Pages: 44 in PDF or view online for FREE

DSC-WX220

3-1

When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust manual in the Adjust station and execute the “Destination Data Write”.

When you replace to the repairing board, get the data from the former one.
Start the Adjust manual in the Adjust station and perform “Restore Data” to get the data. 
The data getting for this model is as follows.

• Product ID & USB Serial No. Data
• Linear Matrix and AWB 3200-5800K Data
• Lens Data

The unit is shipped after an ID (USB Serial No.) unique to each unit and an ID (Product ID) unique to each model have been written.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust manual in the Adjust station and execute the “Product ID & USB 
Serial No. Input” and enter these IDs.

Note:  A newly entered Product ID is not always equal to the ID before board replacement. If the new ID differs from the previous ID, it may cause a differ-

ence from the ID registered by the customer.

When a board that contains Wi-Fi has been replaced or when replacing a board that contains the main IC (CPU), the IC’s unique number (MAC 
address) must be reloaded.
Perform the following procedure to reload the IC’s unique number (MAC address).

1.  Download the latest-version Adjust manual.
2.  Install the downloaded Adjust manual.
3.  Perform “Wireless LAN Setting (MAC Address)” on the ADJUST tab.
4.  Perform the following operations for the unit.
  

MENU 

→

(Wireless) 

→ [Disp MAC Address] → ●

5.  Confirm that the displayed MAC address has been updated.

Applicable parts

•  SY-1037 BOARD, COMPLETE (SERVICE)

Note: The LOAD and WRITE function in Adjustment Data Backup on the DATA tab in the Adjust manual overwrites all data of the unit.
 

Therefore, the MAC address updated during the above procedure is also overwritten.

Perform the above operations after all work has been done.

After the replacement and repair, the MAC address is changed, and thus the re-setting for connection devices is required. Accordingly, download 
the Flyer of WLAN Reset (Flyer of WLAN Reset_9834752[][].pdf) and print out it, and attach it to the set when returning the set to customer.

DSC-WX220

3-2

Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)

OK 

(The flexible board was plugged in straight 
and completely)

NG 

(The flexible board was plugged in 
crooked.)

NG 

(The flexible board was not plugged in 
completely.)

Flexible

Board

Flexible
Board

Connector

Connector

Reference line

Flexible
Board

Connector

Connector

Flexible

Board

Reference line

Connector

Connector

Flexible
Board

Flexible

Board

Reference line

Fig. 1

Fig. 2

Fig. 3

When opening the connector's holder in direction A, do not open 
it with excessive force.

When closing the connector's holder, press it evenly while pushing 
a flexible board in direction B.

Holder

Connector

Flexible Board

A

A

Holder

Insulation side

Connector

Flexible Board

B

•  Make sure that the flat cable and flexible board are not cracked 

or bent at the contact end.

•  Do not apply excessive force to the gilded flexible board.

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

•  The proper way to disconnect a connector is to grab the con-

nector instead of the wires.  If you pull on the wires, they might 
be broken.

•  The proper way to connect a connector is to grab the connector 

instead of the wires.  If you push on the wires, they might be 
broken.

When replacing the lens, read the QR code given on the data sheet 
of the replacement lens for service.
Start the Adjust manual and read the QR code using a QR code 
reader.
The read data is used for adjustment after replacement.
Select “Lens Data Carry” on the ADJUST tab of the Adjust 
manual, and click the QR code data load and write button to 
load the file.

QR cord

DSC-WX220

3-3

The charging capacitor for the flash has been charged at high voltage.
Therefore, there is a possibility of an electric shock if you directly handle this capacitor.
The high-voltage charge will not be discharged by simply turning off the unit’s power.
Make sure any remaining voltage is discharged by short-circuiting the flash capacitor with a Short Jig.
 

Make a Short Jig by connecting a small clip to each lead of a resistor with a rated value of approximately 1 k

Ω/1 W.

In order to prevent an electric shock, wrap insulating tape completely around the resistor and its leads.

Resistor with a rated value of approximately 1 k

Ω/1 W (2CTV0Q

Wrap insulating tape completely around the resistor and its leads.

Small clip

Small clip

Perform the following procedure to check the Wi-Fi function.

Required equipment: Windows personal computer with Wi-Fi interface

1.  Turn on the power of the unit.
2.  Press [MENU] button and select 

(Wireless) 

→ [Ctrl w/ Smartphone] in the menu.

3.  Press set button in the center of the control wheel to open the “Wi-Fi Standby” screen.
4.  When preparation for Wi-Fi has been completed, the following screen opens and a password for Wi-Fi connection is displayed.

Ctrl w/ Smartphone

Operate smartphone to connect to

this device via Wi-Fi.

SSID 

DIRECT-XXXX:DSC-XXXX

Password

 XXXXXXXX

Device Name

 DSC-XXXX

Cancel

5.  Confirm on the personal computer that the unit is detected as a connectable wireless network.
6.  To further confirm that the unit is connectable, connect the unit to the personal computer and select “Network and Internet” 

→ “Manage 

Wireless Networks” from Control Panel to open the network connection list. The unit is included in the list.

XXXX:DSC-XXXX

DSC-WX220

3-4

3-1.  SY-1037基板交換時の注意

仕向けデータ

補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
Adjust stationからAdjust manualを起動させて「Destination Data Write」を実行させてください。

リストアデータ

補修用基板と交換する時，交換前の基板よりデータを取得してください。
データの取得はAdjust stationからAdjust manualを起動させて「Restore Data」を実行させてください。
本機で取得されるデータは下記になります。

･ Product ID & USB Serial No. Data
･ Linear Matrix and AWB 3200-5800K data
･ Lens Data

USBシリアルNo.およびプロダクトIDについて

本機はセット固有のID（USBシリアルNo.）と機種固有のID（プロダクトID）を書き込んだ後に出荷されています。
新品の補修用基板にはこれらのIDが書き込まれていないため，基板交換後にIDを入力する必要があります。
補修用基板に交換した後はAdjust stationからAdjust manualを起動し，「Product ID & USB Serial No. Input」を実行させてIDを入
力してください。

Note:  新しくプロダクトIDを入力すると，必ずしも基板交換前のIDと同じIDになるとは限りません。新しいIDと元のIDが違う場合にはお客様

がユーザー登録されているIDと相違が出てしまう可能性があります。

MAC アドレスの更新

Wi-Fi  搭載基板を交換した時，またはメイン  IC  (CPU)  が搭載されている基板を交換した場合，IC  の固有番号  (MAC  アドレス) 
を取り込み直す必要があります。
下記の作業を実施して，IC の固有番号 (MAC アドレス) を取り込み直してください。

1.  最新版の Adjust manual をダウンロードする。
2.  ダウンロードした Adjust manual をインストールする。
3.  Adjust Manualを起動し，ADJUST タブにある「Wireless LAN Setting (MAC Address)」を実施する。
4.   セット本体を下記のように操作する。
  

MENU →

(ワイヤレス) → ［MACアドレス表示］ → 中央の●で決定。

5.   MAC アドレス の表示が更新されていることを確認する。

対象となる部品
･  SY-1037 BOARD, COMPLETE (SERVICE)

Note:  

 Adjust manual 内の DATA タブにある，Adjustment Data Backup にある機能，LOAD and WRITE は，セットの全てのデータを上書き
します。そのため，上記の操作で更新した MAC アドレス も上書きされてしまいます。

上記の操作は全ての作業を実施した後に行ってください。

交換修理後はMAC アドレスが変更されていますので，お客様に接続機器の再設定をしていただく必要があります。
そのためFlyer of WLAN Reset（Flyer of WLAN Reset_9834752[][].pdf）をダウンロードしてプリント出力し，セットに添付して
返却してください。