Sony DSC-WX170 (serv.man2) Service Manual ▷ View online
DSC-WX170_L2
2-2
– ENGLISH –
– JAPANESE –
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked
of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, don’t press down at wire of con-
nector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE CHARGING CAPACITOR (C901)
The charging capacitor is charged up to the maximum 330 V
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω/1 W
Wrap insulating tape.
1 k
Ω/1 W
Wrap insulating tape.
ST-284 Flexible
Board
Board
ST-284 Flexible
Board
Board
C901
R:1 k
Ω/1 W
C901
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.
Short-circuit between two points with
the short jig about 10 seconds.
(Part code: 1-215-869-11)
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け,
折れ等がないことを確認する。
また,コネクタへの接続は,差し込み不足や斜め差しになら
ないように注意する。
• コネクタを取り外す時に,線材部(極細)を持って引っ張ると
断線する恐れがありますので,絶対に線材部(極細)を持って
引っ張らないでください。
引っ張らないでください。
• 線材部(極細)を押さえながらコネクタを差し込むと,線材部
(極細)が断線する恐れがありますので,絶対に線材部(極細)
には負担をかけないでください。
• 金メッキされているフレキシブル基板には,強い負担をかけ
ないでください。
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
ストロボ用充電コンデンサ(C901)の放電
ストロボ用充電コンデンサは最大330Vの電圧で充電され
ています。
この高電圧で充電されたコンデンサに手を触れた場合,
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
ています。
この高電圧で充電されたコンデンサに手を触れた場合,
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
ショート治具の準備
ショート治具は1kΩ/1W抵抗(1-215-869-11)の両端に
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
ST-284 Flexible
Board
Board
ST-284 Flexible
Board
Board
C901
R:1 k
Ω/1 W
ㇱຠࠦ࠼㧦
1-215-869-11
ࠦࡦ࠺ࡦࠨߩ㔚
ࡈ࠶ࠪࡘ࡙࠾࠶࠻ߩ㔚Ḯࠦࡦ࠺ࡦࠨ
ߩ┵ሶ㑆ࠍ࡚ࠪ࠻ᴦౕߢ⚂⑽㑆
ធ⛯ߔࠆޕ
ࡈ࠶ࠪࡘ࡙࠾࠶࠻ߩ㔚Ḯࠦࡦ࠺ࡦࠨ
ߩ┵ሶ㑆ࠍ࡚ࠪ࠻ᴦౕߢ⚂⑽㑆
ធ⛯ߔࠆޕ
C901
DSC-WX170_L2
2-3
2-1. EXPLODED VIEWS
2-1-1. REAR SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
4-419-297-51
COVER (170), DC (BLACK)
1
4-419-297-61
COVER (170), DC (WHITE)
1
4-419-297-71
COVER (170), DC (PINK)
1
4-419-297-81
COVER (170), DC (GOLD)
2
A-1896-127-A LCD BLOCK ASSY (SERVICE) (Note 2)
3
4-415-061-01
SPACER LCD (250), SY
4
4-292-223-01
CUSHION (760), LCD (Note 3)
5
A-1896-140-A TP BLOCK ASSY (SERVICE) (Note 3)
6
4-418-360-01
SHEET (H) (250), ADHESIVE
7
X-2585-118-1
CABINET (REAR) ASSY (270C) (BLACK)
7
X-2585-119-1
CABINET (REAR) ASSY (270D) (WHITE)
7
X-2585-120-1 CABINET (REAR) ASSY (270E) (PINK)
7
X-2585-121-1 CABINET (REAR) ASSY (270F) (GOLD)
LCD901 8-753-386-79
PANEL MODULE (PD10-WBJD) (Note 3)
#212
4-270-114-01
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
#237
4-270-114-21
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1, 4)
#244
4-412-769-21
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
#259
4-412-769-61
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1, 4)
1. Remove in numerical order (
1
to
3
) in the left figure.
DISASSEMBLY
1
#212/#244 X 4 → #237/#259 X 2
#212
#244
#212
#244
#237
#259
Bottom View
Left View
Right View
Screw
Note
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
Cabinet's Color
Table 2-1
Note 1
THE COMBINATION OF CABINET’S
COLOR AND SCREW
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
#212 (Silver)
#244 (Black)
#237 (Silver)
#259 (Black)
WHITE/GOLD
BLACK/PINK
WHITE/GOLD
BLACK/PINK
Note 3: Refer to “Assembly-4: Attaching Method of LCD and
TP Block Assy”.
Note 3: “Assembly-4: Attaching Method of LCD and TP Block
Assy.”を参照してください。
1.4
3.0
#212:
4-270-114-01
(Silver)
M1.4 X 3.0
#237:
2.0
1.4
(Silver)
M1.4 X 2.0
4-270-114-21
#244: M1.4 X 3.0
(Black)
4-412-769-21
4-412-769-21
3.0
1.4
#259:
2.0
1.4
4-412-769-61
M1.4 X 2.0
(Black)
(Black)
Front/Top Section
(See page 2-4)
(Claws)
(Claw)
(Claws)
(Claws)
#237
#259
(Note 1, 4)
#259
(Note 1, 4)
#212
#244
(Note 1)
#244
(Note 1)
#212
#244
(Note 1)
#244
(Note 1)
#212
#244
(Note 1)
#244
(Note 1)
LCD901
(Note 3)
(Note 3)
1
1
7
4
(Note 3)
5
(Note 3)
2
(Note 2)
3
6
2
3
Note on assembling the LCD MODULE
Slide the LCD block to completely
engage the two claws with the two holes.
engage the two claws with the two holes.
LCD block
Claws
Claws
Note 2
LCDブロックをスライドさせて、ツめ2箇所を
穴2箇所に完全にはめ込んでください。
Note 2
LCD MODULE 組立て時の注意事項
ツメ
LCDブロック
穴
Install a screw straight
to the screw hole.
to the screw hole.
Note 4
ねじを、ねじ穴に対して
まっすぐに取り付けて
ください。
まっすぐに取り付けて
ください。
Note 4
DSC-WX170_L2
2-4
2-1-2. FRONT/TOP SECTION
ns : not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
X-2585-122-1 CABINET (FRONT) ASSY (270C) (BLACK)
51
X-2585-123-1 CABINET (FRONT) ASSY (270D) (WHITE)
51
X-2585-124-1 CABINET (FRONT) ASSY (270E) (PINK)
51
X-2585-125-1 CABINET (FRONT) ASSY (270F) (GOLD)
52
X-2585-126-1 COVER ASSY (270C), TERMINAL (BLACK)
52
X-2585-127-1 COVER ASSY (270D), TERMINAL (WHITE)
52
X-2585-128-1 COVER ASSY (270E), TERMINAL (PINK)
52
X-2585-129-1 COVER ASSY (270F), TERMINAL (GOLD)
53
4-419-293-01
CABINET (L) (170), SIDE (BLACK)
53
4-419-293-21
CABINET (L) (170), SIDE (PINK)
53
4-419-293-31
CABINET (L) (170), SIDE (WHITE, GOLD)
54
4-419-295-01
CABINET (G) (170), SIDE (BLACK)
54
4-419-295-21
CABINET (G) (170), SIDE (PINK)
54
4-419-295-31
CABINET (G) (170), SIDE (WHITE, GOLD)
55
1-489-357-11 FLASH
UNIT
56
A-1860-729-A ST-284 FLEXIBLE BOARD, COMPLETE (Note 2)
57
4-266-381-01
SHEET, CABINET UPPER (770)
58
4-419-308-01
BASE, SHEET MICROPHONE
59
4-419-310-01
FRAME, SHEET (TOP)
60
X-2585-114-1
CABINET (UPPER) ASSY (270C) (BLACK)
60
X-2585-115-1
CABINET (UPPER) ASSY (270D) (WHITE)
60
X-2585-116-1
CABINET (UPPER) ASSY (270E) (PINK)
60
X-2585-117-1
CABINET (UPPER) ASSY (270F) (GOLD)
61
4-440-890-01
SHEET (SY (270))
62
4-421-333-01
SHEET CD, ELECTROSTATIC
63
4-419-320-01
SHEET (SY), RADIATION
64
4-415-062-01
SHEET (LCD) (250), RADIATION
65
4-411-649-01
RUBBER (150), MICROPHONE
C901
1-118-015-11
ELECT 53uF 330V
#71
3-208-537-01
0+Z M1.4X2 NEW TORASUTA
#212
4-270-114-01
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
#244
4-412-769-21
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
1. Remove in numerical order (
1
to
7
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇-X
: Solder
DISASSEMBLY
Note
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
Cabinet's Color
Table 2-1
Note 1
THE COMBINATION OF CABINET’S
COLOR AND SCREW
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
#212 (Silver)
#244 (Black)
WHITE/GOLD
BLACK/PINK
Screw
#71: M1.4 X 2.0
(Red)
3-208-537-01
3-208-537-01
2.0
1.4
1.4
3.0
#212:
4-270-114-01
(Silver)
M1.4 X 3.0
2
#212/#244 X 1
5
#71 X 1
#212
#244
Bottom View
#71
Back View
7
(
7
-1
) Cabinet Upper Sheet (770) → (
7
-2
) Sheet SY (270)
#244: M1.4 X 3.0
(Black)
4-412-769-21
4-412-769-21
3.0
1.4
Note 2: Refer to “Assembly-2: Precaution During of ST-284
Flexible Board.”.
Note 2: “Assembly-2: Precaution During of ST-284 Flexible
Board.”を参照してください。
(Claws)
(Claw)
(Claw)
(Claw)
(Bosses)
(Claw)
(Bosses)
(Boss)
(Claw)
7
56
58
55
65
57
ns
C901
7
-1
(Note 2)
6
2
1
4
3
52
51
53
54
62
64
61
7
-2
63
#212
#244
(Note 1)
#71
ns
5
60
59
Main Section
(See page 2-5)
2
1
6
DISCHARGING OF THE CHARGING CAPACITOR
ストロボ用充電コンデンサの放電
DSC-WX170_L2
2-5
2-1-3. MAIN SECTION
ns : not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
4-434-556-01
COVER (270), SP
102
A-1896-128-A SERVICE, BT HOLDER ASSY (270C) (BLACK)
102
A-1896-129-A SERVICE, BT HOLDER ASSY (270D) (WHITE)
102
A-1896-130-A SERVICE, BT HOLDER ASSY (270E) (PINK)
102
A-1896-131-A SERVICE, BT HOLDER ASSY (270F) (GOLD)
103
4-419-301-01
TERMINAL, SHEET (BT)
104
1-883-820-11
BT-068 FLEXIBLE BOARD
105
A-1889-362-A SY-1004 BOARD, COMPLETE (SERVICE)
106
4-421-334-01 GASKET
(U)
107
4-419-313-01
FLEXIBLE, SHEET LENS
* 108
4-199-794-01
SHEET, BT ELECTROSTATIC
BT001
1-756-813-11
LITHIUM RECHARGEABLE BATTERY
*BT901 1-780-826-11
TERMINAL BOARD, BATTERY
SP901
1-858-302-61
LOUDSPEAKER (0.8CM) (Note 3)
1. Remove in numerical order (
1
to
4
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇-X
: Solder
DISASSEMBLY
SY
-1004
: BT001 (LITHIUM RECHARGEABLE BATTERY)
Board on the mount position.
(See page 6-13 of Level 3)
Board on the mount position.
(See page 6-13 of Level 3)
ns
ns
1
Lens Block Section
(See page 2-6)
(Note 1, 2)
4
102
3
105
101
2
104
103
BT001
BT901
ns
2
SP901
(Note 3)
107
108
106
Note
2
(
2
) SP (COVER)
Note 3: Refer to “Assembly-1: Precaution During Speaker Installation.”.
Note 2: Refer to “Assembly-3: Precaution During of Lens Block.”.
Note 3: “Assembly-1: Precaution During Speaker Installation” を参照してください。
Note 2: “Assembly-3: Precaution During of Lens Block.” を参照してください。
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は、正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は、取扱指示に従って処分してください。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は、取扱指示に従って処分してください。
Note 1:
Hold the Lens Block at the
center of both sides.
Do not hold the following part.
Hold here.
PRECAUTIONS WHEN HOLDING THE LENS BLOCK
Lens Barrier
Very weak
Zoom Motor
Very weak
Zoom Motor
Very weak
Yoke
Very weak
Yoke
Very weak
Focus Lens
Very weak
Click on the first or last page to see other DSC-WX170 (serv.man2) service manuals if exist.