Sony DSC-WX170 (serv.man2) Service Manual ▷ View online
DSC-WX170_L2
1-10
1-8. ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD
1-9. DC MOTOR WORM ASSY REPLACING METHOD
Note: As for the figure below, this model and the shape
of the main body are different.
下図は当機種と本体の形状が異なります。
Note:
Barrier Assy
Claws
Claws
Barrier Assy
Claws
Claws
Hole
Barrier
Lever
Installation
Removal
Ornamental Ring A
Barrier Tapes
Barrier Assy
Barrier Tapes
Ornamental Ring A
Disengage the four claws and remove the Barrier Assy.
Fit the four claws while inserting the Barrier Lever into the hole and attach the Barrier Assy.
Peel off the release papers of the Barrier Tapes.
Install the Ornamental Ring A and press it lightly.
Install the Ornamental Ring A and press it lightly.
Turn on the power switch and extend the lens (TELE end).
Detach the battery.
Apply alcohol to two gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below.
Turn the Ornamental Ring A clockwise and counterclockwise to detach it.
Detach the battery.
Apply alcohol to two gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below.
Turn the Ornamental Ring A clockwise and counterclockwise to detach it.
Solvent
A
Tweezers
Claws
Sensors
FG Leaf
Spring
Claw
FPC Retainer
Z Retainer
Removal
1. Disengage the two claws and remove the FG Leaf Spring.
2. Remove the two Sensors.
3. Disengage the claw and remove the FPC Retainer.
4. Peel off the FPC Tape.
5. Disconnect the two Flexible Boards from the Connectors on the LF-139 Flexible Board.
1. Disengage the two claws and remove the FG Leaf Spring.
2. Remove the two Sensors.
3. Disengage the claw and remove the FPC Retainer.
4. Peel off the FPC Tape.
5. Disconnect the two Flexible Boards from the Connectors on the LF-139 Flexible Board.
6. Remove the LF-139 Flexible Board.
7. Remove the four screws and remove the Z Retainer and the Sensor.
7. Remove the four screws and remove the Z Retainer and the Sensor.
8. Detach the Rear Mirror Plate and remove the Gear Worm Wheel, Gear A, and Gear B.
9. Remove the two screws and remove solder at two locations to detach the DC Motor Worm Assy.
9. Remove the two screws and remove solder at two locations to detach the DC Motor Worm Assy.
Gear A
Gear B
Gear Worm
Wheel
Ribs
Rib
Rib
Rib
Boss
Boss
Screws
Screws
Screw
Sensor
Boss
Boss
Flexible Board
LF-139 Flexible Board
LF-139 Flexible Board
Flexible Board
FPC Tape
Connector
Connector
Rear Mirror
Plate
DC Motor Worm Assy
Solders
DSC-WX170_L2
1-11
1-10. THREE TUBE LUBRICATIONG BLOCK ASSY AND GROUP 1 FRAME REPLACING METHOD
Fold inside
Draw up
Claws
Sensors
OK
NG
FG Leaf
Spring
FG Leaf Spring
FG Leaf Spring
Claw
FPC Retainer
Z Retainer
Installation
1. Install the LF-139 Flexible Board to the DC Motor Worm Assy and solder the LF-139 Flexible Board at two locations.
2. Install the DC Motor Worm Assy to the Stationary Tube Assy with two screws.
3. Install the Gear Worm Wheel, Gear A, and Gear B.
4. Install the Rear Mirror Plate.
1. Install the LF-139 Flexible Board to the DC Motor Worm Assy and solder the LF-139 Flexible Board at two locations.
2. Install the DC Motor Worm Assy to the Stationary Tube Assy with two screws.
3. Install the Gear Worm Wheel, Gear A, and Gear B.
4. Install the Rear Mirror Plate.
5. Install four screws and the Z Retainer. Tighten the screws in the order of numbers in the figure below.
6. Install the LF-139 Flexible Board.
6. Install the LF-139 Flexible Board.
7. Connect the two Flexible Boards to the Connectors on the LF-139 Flexible Board.
8. Stick the FPC Tape as shown in the figure below.
9. Install the two Sensors and attach the FG Leaf Spring.
Note: Attach the FG Leaf Spring in the correct orientation.
10. Attach the FPC Retainer.
8. Stick the FPC Tape as shown in the figure below.
9. Install the two Sensors and attach the FG Leaf Spring.
Note: Attach the FG Leaf Spring in the correct orientation.
10. Attach the FPC Retainer.
1
2
3
4
Screws
Screws
Screw
Sensor
LF-139 Flexible Board
LF-139 Flexible Board
Flexible Board
Flexible Board
FPC Tape
FPC Tape
Rib
Connector
Connector
Gear A
Gear B
Gear Worm
Wheel
Rear Mirror
Plate
DC Motor Worm Assy
Solders
Ribs
Rib
Rib
Rib
Boss
Boss
Boss
Boss
Claws
Sensors
FG Leaf
Spring
Claw
FPC Retainer
4. Disconnect the Flexible Board from the Connector on the LF-139 Flexible Board.
6. Disconnect the Flexible Board from the Connector on the LF-139 Flexible Board.
5. Peel off the FPC Tape.
Flexible Board
Flexible Board
FPC Tape
Connector
Connector
Ribs
Rib
Rib
Rib
Boss
Boss
Boss
Boss
LF-139 Flexible Board
Z Retainer
Screws
Screw
Sensor
7. Remove the LF-139 Flexible Board.
8. Remove the four screws and remove the Z Retainer and the Sensor.
Removal
1. Disengage the two claws and remove the FG Leaf Spring.
2. Remove the two Sensors.
3. Disengage the claw and remove the FPC Retainer.
1. Disengage the two claws and remove the FG Leaf Spring.
2. Remove the two Sensors.
3. Disengage the claw and remove the FPC Retainer.
DSC-WX170_L2
1-12
A
A
Flexible Board
Flexible Board
Main Body
Main Body
Rotary Cam Tube
Rotary Tube
Stationary Tube Assy
Gear A
Gear A
Gear B
Gear Worm
Wheel
Rear Mirror
Plate
9. Detach the Rear Mirror Plate and remove the Gear Worm Wheel, Gear A, and Gear B.
10. Turn the Gear in the arrow direction to extend the Mirror Plate slightly.
11. Turn portion A in the arrow direction to TELE end and remove the Flexible Board from the hole in the Stationary Tube Assy.
11. Turn portion A in the arrow direction to TELE end and remove the Flexible Board from the hole in the Stationary Tube Assy.
12. Turn portion A in the arrow direction to WIDE end and detach the Main Body from the Stationary Tube Assy.
13. Remove the Main Body in the arrow direction.
14.
14.
Remove the Rotary Cam Tube from the Rotary Tube in the arrow direction.
Lens Block
1 Frame Assy
Cam Tube A
3 Group Assy
Tweezers
Claw
Claw
15. Turn the 3 Group Assy approx. 20° in the arrow direction.
16. Disengage the three Claws with tweezers.
16. Disengage the three Claws with tweezers.
17. Remove the Lens Block.
18. Remove the 1 Frame Assy from the Cam Tube A.
18. Remove the 1 Frame Assy from the Cam Tube A.
DSC-WX170_L2
1-13
Cam Tube B
Cam Tube B
2 Group Frame
3 Group Assy
Straight Tube Block
Straight Tube
Straight Tube
19. Fully turn the Cam Tube B in the arrow direction.
20. Remove the 2 Group Frame.
21. Remove the Straight Tube Block.
21. Remove the Straight Tube Block.
22. Turn the Straight Tube in the arrow direction to detach it from the Cam Tube B.
White Part
Thinnest Groove
Cam Tube B
Cam Tube B
Lever
Cutout
Straight Tube
Straight Tube
3 Group Assy
Straight Tube Block
2 Group Frame
2 Group Frame
Shaft of 3 Group Assy
Top side view
Installation
1. Align the Lever with the cutout as shown in the figure, and then install the Straight Tube to the Cam Tube B.
Note: Be sure to set the Straight Tube at the correct insertion position.
2. Turn the Straight Tube in the arrow direction to the maximum.
Note: Be sure to set the Straight Tube at the correct insertion position.
2. Turn the Straight Tube in the arrow direction to the maximum.
3. Install the Straight Tube Block aligning the thinnest groove with the white part as shown in the figure, and then turn
the Cam Tube B in the arrow direction to the maximum.
the Cam Tube B in the arrow direction to the maximum.
4. Install the 2 Group Frame at a position where the Shaft of 3 Group Assy is visible through the cutout of the 2 Group Frame.
Click on the first or last page to see other DSC-WX170 (serv.man2) service manuals if exist.