DOWNLOAD Sony DSC-W830 (serv.man2) Service Manual ↓ Size: 3.2 MB | Pages: 27 in PDF or view online for FREE

DSC-W830

3-2

Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)

OK 

(The flexible board was plugged in straight 
and completely)

NG 

(The flexible board was plugged in 
crooked.)

NG 

(The flexible board was not plugged in 
completely.)

Flexible

Board

Flexible
Board

Connector

Connector

Reference line

Flexible
Board

Connector

Connector

Flexible

Board

Reference line

Connector

Connector

Flexible
Board

Flexible

Board

Reference line

Fig. 1

Fig. 2

Fig. 3

When opening the connector's holder in direction A, do not open 
it with excessive force.

When closing the connector's holder, press it evenly while pushing 
a flexible board in direction B.

Holder

Connector

Flexible Board

A

A

Holder

Insulation side

Connector

Flexible Board

B

•  Make sure that the flat cable and flexible board are not cracked 

or bent at the contact end.

•  Do not apply excessive force to the gilded flexible board.

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

•  The proper way to disconnect a connector is to grab the con-

nector instead of the wires.  If you pull on the wires, they might 
be broken.

•  The proper way to connect a connector is to grab the connector 

instead of the wires.  If you push on the wires, they might be 
broken.

The charging capacitor is charged up to the maximum 330 V potential.
There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage 
which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be discharged.

Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent electrical shock.

Wrap insulating tape.

1 k

Ω/1 W

The changed portions from
Ver. 1.0 are shown in blue.

DSC-W830

3-3

The data can be copied/erased by the operations on the MENU screen. (When erasing the data, execute formatting the internal memory.)

Note 1:When replacing the SY-1035 board, erase the data in internal memory of the board before replacement.
Note 2:When replacing the SY-1035 board, execute formatting and initialize the internal memory after replacement.

Copy

Copies all images in the internal memory to a memory card.

1.  Insert a memory card with sufficient free capacity into the camera.

2. MENU -   (Settings) - 

 (Memory Card Tool) - [Copy] - [OK] - 

Make sure there is sufficient battery power. Otherwise, the battery power may run out when you
attempt to copy image files, causing the copy to fail and possibly corrupt the data.
Images cannot be copied individually.
Original images in internal memory are retained even after copying. To delete contents of internal
memory, remove the memory card after copying, then format internal memory ([Format] in
[Memory Card Tool]).
A new folder is created on the memory card and all data will be copied to it. You cannot choose a
specific folder and copy images to it.

Format

Formats the memory card.

When you use a memory card with this camera for the first time, it is recommended to format the card

using the camera for stable performance of the memory card before shooting. Note that formatting

permanently erases all data on the memory card, and is unrecoverable. Save precious data on a

computer, etc.

1. MENU -   (Settings) -   (Internal Memory Tool) - [Format] - [OK] - 

Note that formatting permanently erases all data including even protected images.

The changed portions from
Ver. 1.0 are shown in blue.

DSC-W830

3-4

Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.
To change settings is enabled with using the writing enabler tool (Write Enable Tool) on the Adjust Manual is activating from the Adjust Station.

1)  Start the Adjust Manual from the Adjust Station.

2) Click 

 (Write Enable Tool) button.

3)  Click “Activate Write Enable Mode” button.

4)  Upon completion of the setting change, the following message will be displayed.

5)  Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).
 

Perform the following procedure at the method order 5) when using [Write Enable Tool]. 

 

1.   Disconnect the USB cable from the camera.

 

2.   Reconnect the USB cable to the camera so that the camera is connected in  the Mass-Storage mode.

6)  Write the data read out into the PC to the internal memory of the camera.
7)  Disconnect the PC from the camera, and turn off the camera.

Note: By turning off the camera, the write enable setting is reset.

Use the battery (NP-BN) on repairing.
The external battery source cannot be used on repairing.

The changed portions from
Ver. 1.0 are shown in blue.

DSC-W830

3-5

When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash 
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the MENU screen.

Initialize

Initializes settings to the default setting.

Even if you execute this function, images are retained.

1. MENU -   (Settings) - 

 (Main Settings) - [Initialize] - [OK] - 

Be sure not to remove the battery pack while initializing.

Dedicated A/V cable is not supplied with this model.
For details of the dedicated A/V cable, refer to the Note 1 on the “ACCESSORIES”.

The changed portions from
Ver. 1.0 are shown in blue.