Sony DSC-W610 (serv.man2) Service Manual ▷ View online
DSC-W610_L2
2-2
– ENGLISH –
– JAPANESE –
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked
of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, don’t press down at wire of con-
nector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE CHARGING CAPACITOR (C901)
The charging capacitor is charged up to the maximum 330 V
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω/1 W
Wrap insulating tape.
1 k
Ω/1 W
Wrap insulating tape.
MA-480 Flexible
Board
Board
R:1 k
/1 W
C901
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.
Short-circuit between two points with
the short jig about 10 seconds.
(Part code: 1-215-869-11)
Ω
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け，
折れ等がないことを確認する。
また，コネクタへの接続は，差し込み不足や斜め差しになら
ないように注意する。
• コネクタを取り外す時に，線材部（極細）を持って引っ張ると
断線する恐れがありますので，絶対に線材部（極細）を持って
引っ張らないでください。
引っ張らないでください。
• 線材部（極細）を押さえながらコネクタを差し込むと，線材部
（極細）が断線する恐れがありますので，絶対に線材部（極細）
には負担をかけないでください。
• 金メッキされているフレキシブル基板には，強い負担をかけ
ないでください。
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
ストロボ用充電コンデンサ（C901）の放電
ストロボ用充電コンデンサは最大330Vの電圧で充電され
ています。
この高電圧で充電されたコンデンサに手を触れた場合，
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず，残留しています。こ
のため，下記の方法で残留電圧を放電してください。
ています。
この高電圧で充電されたコンデンサに手を触れた場合，
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず，残留しています。こ
のため，下記の方法で残留電圧を放電してください。
ショート治具の準備
ショート治具は1kΩ/1W抵抗（1-215-869-11）の両端に
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
MA-480 Flexible
Board
Board
C901
R:1 k
Ω /1 W
ㇱຠࠦ࠼㧦
1-215-869-11
ࠦࡦ࠺ࡦࠨߩ㔚
ࡈ࠶ࠪࡘ࡙࠾࠶࠻ߩ㔚Ḯࠦࡦ࠺ࡦࠨ
ߩ┵ሶ㑆ࠍ࡚ࠪ࠻ᴦౕߢ⚂⑽㑆
ធ⛯ߔࠆޕ
ࡈ࠶ࠪࡘ࡙࠾࠶࠻ߩ㔚Ḯࠦࡦ࠺ࡦࠨ
ߩ┵ሶ㑆ࠍ࡚ࠪ࠻ᴦౕߢ⚂⑽㑆
ធ⛯ߔࠆޕ
DSC-W610_L2
2-3
2-1. EXPLODED VIEWS
2-1-1. REAR SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
4-297-229-01
CABINET (R (030)), SIDE
2
4-415-046-01
INSULATING SHEET (030), LCD
3
4-264-762-01
SHEET2 (700), LCD INSULATING
4
4-417-256-11
CUSHION (030), LCD (Note 2)
5
4-168-182-02
WINDOW (670), LCD (Note 2)
6
1-880-210-11
FPC-020 FLEXIBLE BOARD
7
A-1851-791-A SW-584 BOARD, COMPLETE
8
4-297-230-01
LID (030), MC (SILVER)
8
4-297-230-11
LID (030), MC (BLACK)
8
4-297-230-21
LID (030), MC (PINK)
8
4-297-230-31
LID (030), MC (GREEN)
8
4-297-230-41
LID (030), MC (BLUE)
9
X-2582-684-1 CABINET (REAR) ASSY (SILVER) (Note 3)
9
X-2582-685-1 CABINET (REAR) ASSY (BLACK) (Note 3)
9
X-2582-686-1 CABINET (REAR) ASSY (PINK) (Note 3)
9
X-2582-687-1 CABINET (REAR) ASSY (GREEN) (Note 3)
9
X-2582-688-1 CABINET (REAR) ASSY (BLUE) (Note 3)
LCD901 1-802-984-11 LCD
MODULE
#209
4-264-751-01
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
#243
4-412-769-01
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
1. Remove to numerical order (
1
to
6
) in the left figure.
DISASSEMBLY
1
#209/#243 X 5
Screw
5
5
7
(Claws)
1
(Claw)
Front/Top Section
(See page 2-4)
4
1
9
(Note 3)
6
LCD901
5
(Note 2)
4
3
(Note 2)
#209
#243
(Note 1)
#243
(Note 1)
#209
#243
(Note 1)
#243
(Note 1)
#209
#243
(Note 1)
#243
(Note 1)
2
8
3
1
6
2
#209
#243
#209
Bottom View
Left View
Right View
#243
#209
#243
Note
Note 1
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
The screw pointed
is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
#209 (Silver)
SILVER/PINK/GREEN
#243 (Black)
BLACK/BLUE
Cabinet's Color
Table 2-1
Note 2: Refer to “Assembly-5: Attaching Method of LCD
Cushion (030), LCD Window (670)”.
Note 2: “Assembly-5: Attaching Method of LCD Cushion
(030), LCD Window (670)”を参照してください。
Note 3: Refer to “Assembly-4: Precaution During of Cabinet
(Rear) Assy Installation.”.
Note 3: “Assembly-4: Precaution During of Cabinet (Rear)
Assy Installation.”を参照してください。
4
#209: M1.4 X 3.5
(Silver)
4-264-751-01
4-264-751-01
1.4
3.5
DISCHARGING OF THE CHARGING CAPACITOR
ストロボ用充電コンデンサの放電
#243: M1.4 X 3.5
(Black)
4-412-769-01
4-412-769-01
3.5
1.4
DSC-W610_L2
2-4
2-1-2. FRONT/TOP SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
X-2582-679-1 CABINET (FRONT) ASSY (SILVER)
51
X-2582-680-1 CABINET (FRONT) ASSY (BLACK)
51
X-2582-681-1 CABINET (FRONT) ASSY (PINK)
51
X-2582-682-1 CABINET (FRONT) ASSY (GREEN)
51
X-2582-683-1 CABINET (FRONT) ASSY (BLUE)
52
4-297-227-01
LID (030), BT (SILVER) (Note 2)
52
4-297-227-11
LID (030), BT (BLACK) (Note 2)
52
4-297-227-21
LID (030), BT (PINK) (Note 2)
52
4-297-227-31
LID (030), BT (GREEN) (Note 2)
52
4-297-227-41
LID (030), BT (BLUE) (Note 2)
53
4-264-743-01
LIGHT GUIDE (700)
54
1-489-930-11 FLASH
UNIT
55
A-1851-790-A ST-268 BOARD, COMPLETE
56
4-297-232-01
SHEET (030), ST
57
1-880-206-11
FPC-016 FLEXIBLE BOARD
58
X-2582-689-1 CABINET (UPPER) ASSY (030C)
59
4-410-120-01
SHEET (030), MA RADIATION
60
4-297-226-01
FRAME (030), MAIN
61
4-408-895-01
INSULATING SHEET (030), SY
62
1-885-071-21
MA-480 FLEXIBLE BOARD
63
4-264-746-01
HOLDER (700), CAPACITOR
64
4-264-883-01
TAPE SP (700) (Note 3)
65
4-264-763-01 SHEET, MA (700)
BT900
1-756-813-11
LITHIUM RECHARGEABLE BATTERY
C901
1-116-439-21
CAP, ELECT 56uF 315V
MIC901 1-542-721-41
MICROPHONE BLOCK (Note 3)
SP901
1-858-297-11
LOUDSPEAKER (1.0CM) (Note 3)
#209
4-264-751-01
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
#243
4-412-769-01
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
1. Remove to numerical order (
1
to
7
) in the left figure.
DISASSEMBLY
1
#209/#243 X 1
Screw
: BT900 (LITHIUM RECHARGEABLE BATTERY)
Board on the mount position.
(See page 6-20 of Level3)
Board on the mount position.
(See page 6-20 of Level3)
RV
4
4
(Claw)
3
(Claws)
#209
#243
(Note 1)
2
51
4
55
Main Section
(See page 2-5)
SP901
(Note 3)
(Note 3)
C901
BT900
#209
1
60
61
59
65
MIC901
(Note 3)
(Note 3)
(White)
(Red)
7
62
6
63
(Note 3)
64
(Note 3)
5
53
3
58
54
57
56
52
(Note 2)
Note
Note 3: Refer to “Assembly-3: Precaution During of
MA-480 Flexible Board Installation.”.
4
(
4
) ST Sheet (030)
Note 3: “Assembly-3: Precaution During of MA-480
Flexible Board Installation.”を参照してください。
3
#209 X 1
Note 1
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
The screw pointed
is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
#209 (Silver)
SILVER/PINK/GREEN
#243 (Black)
BLACK/BLUE
Cabinet's Color
Table 2-1
Note 2:
REMOVING METHODE OF THE BT LID
Removing and Installing of the BT lid, after remove
the cabinet (rear) assy and the cabinet (front) assy.
the cabinet (rear) assy and the cabinet (front) assy.
Incline
the BT lid
the BT lid
Remove
the BT lid
the BT lid
Bottom View
#209
#243
Back View
#209
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は、正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は、取扱指示に従って処分してください。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は、取扱指示に従って処分してください。
#209: M1.4 X 3.5
(Silver)
4-264-751-01
4-264-751-01
1.4
3.5
#243: M1.4 X 3.5
(Black)
4-412-769-01
4-412-769-01
3.5
1.4
DSC-W610_L2
2-5
2-1-3. MAIN SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101 X-2582-694-1 BTH ASSY
* 102
* 102
3-289-764-01 GASKET (280)
103
4-297-228-01
CABINET (L (030)), SIDE (SILVER, PINK, GREEN)
103
4-297-228-11
CABINET (L (030)), SIDE (BLACK, BLUE)
104
4-168-198-01
INSULATING SHEET (670) (Note 2)
105
A-1851-909-A SY-285 BOARD, COMPLETE (SERVICE)
106
4-172-234-01
TAPE (4X23), DOUBLE STICK
*BT901 1-780-835-11
TERMINAL BOARD BATTERY (Note 3)
*BT902 1-780-835-11
TERMINAL BOARD BATTERY (Note 3)
*BT903 1-780-835-11
TERMINAL BOARD BATTERY (Note 3)
1. Remove to numerical order (
1
to
4
) in the left figure.
2. The meaning of the sign in left figure is as follows. Be careful when it removes.
◇-X
: Solder
DISASSEMBLY
3
105
BT902
BT903
BT901
(Note 3)
(Note 3)
(Note 3)
1
Lens Block Section
(See page 2-6)
(Note 1)
104
(Note 2)
4
101
2
103
102
106
102
Note
Note 2: Refer to “Assembly-2: Insulating Sheet (670)
Putting Position”.
Note 2: “Assembly-2: Insulating Sheet (670) Putting
Position” を参照してください。
Note 3: Refer to “Assembly-1: Installation Method
of Battery Terminal Board”.
Note 3: “Assembly-1: Installation Method of Battery
Terminal Board” を参照してください。
Note 1:
Hold the Lens Block at the
center of both sides.
center of both sides.
Do not hold the following part.
Hold here.
Lens Flexible Board
PRECAUTIONS WHEN HOLDING THE LENS BLOCK
Click on the first or last page to see other DSC-W610 (serv.man2) service manuals if exist.