Sony DSC-W520 Service Manual ▷ View online
DSC-W520
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the given numerical order.
IDENTIFYING PARTS
View Position
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original one.
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay
should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Due to standardization, replacements in the parts list may be different from the parts specified
in the diagrams or the components used on the set.
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
When indicating parts by reference number,
please include the board name.
Link
ACCESSORIES
ASSEMBLY
DISCHARGING OF THE CHARGING CAPACITOR
• Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
KR : Korea model
Bottom View
Bottom View
Top View
Top View
Back View
Back View
Right View
Right View
Left View
Left View
Front View
1
Front Cover Assy
2
Rear Cover Assy
4
SW Board
5
LCD Module
6
Stroboscope Block Assy
7
Main Frame Section
8
Lens Block
9
Main Board
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
Les composants identifiés par une marque
0
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
DSC-W520
2-2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked or
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, do not pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, do not press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
The charging capacitor is charged up to the maximum 310 V
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
DISCHARGING OF THE CHARGING CAPACITOR
Cut and remove the part of gilt
which comes off at the point.
(Be careful that some
pieces of gilt may be left inside)
Wrap insulating tape.
R:1 kΩ/1 W
(Part code: 1-215-869-11)
Stroboscope
Block Assy
Temporarily peel off
the Sheet (BLACK)
Note:
Note:
High-voltage cautions
High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points with the
short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
Short-circuit between the two points with the
short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
DSC-W520
2-3
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
DISASSEMBLY
1
X-2581-266-1 COVER ASSY (S), FRONT (SILVER)
1
X-2581-267-1 COVER ASSY (B), FRONT (BLACK)
1
X-2581-268-1 COVER ASSY (R), FRONT (RED)
2
4-281-005-01 RETAINER
(Note1)
3
1-811-402-21 LCD
MODULE
4
A-1821-723-A SW BOARD, COMPLETE
5
X-2581-269-1 COVER ASSY (S), REAR (SILVER)
5
X-2581-270-1 COVER ASSY (B), REAR (BLACK)
5
X-2581-271-1 COVER ASSY (R), REAR (RED)
#S1
4-281-030-01 SCREW_M_1.7_3_S
(Note2)
#S2
4-281-031-01 SCREW_M_1.7_3_B
(Note2)
#S3
4-281-032-01 SCREW_M_1.7_2_S
(Note2)
#S4
4-281-603-01
SCREW M1.7_2 (Note2)
1
#S1 / #S2 X 3
→ #S3 / #S4 X 1
2
#S3 / #S4 X 1
Note
1. Remove in numerical order (
1
to
5
) in the left figure.
3
Temporarily peel off the Sheet (BLACK)
4
#S3 X 1
→ Remove the Mylar (
4
)
Note2: THE COMBINATION OF CABINET’S COLOR AND SCREW
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer
to Table 2-1.
For the combination of cabinet's color and screw, please refer
to Table 2-1.
Table 2-1
Screw's
Ref. No. (Parts Color.)
Cabinet's Color
#S1, #S3 (Silver)
SILVER
#S2, #S4 (Black)
BLACK, RED
DISCHARGING OF THE CHARGING CAPACITOR
Bottom View
Left View
#S1
#S2
#S2
#S3
#S4
#S4
#S1
#S2
#S2
Bottom View
#S3
#S4
#S4
Back View
#S3
Mylar
Note1: Refer to “Assembly-1: Putting position of the Retainer” when
you assemble.
#S1
#S2
(Note2)
#S2
(Note2)
#S3
1
1
1(Claw)
4
4
4
4
5
3
Main Frame Section
(See page 2-4)
(See page 2-4)
2
(Note1)
2(Claw)
1(Claw)
1(Claw)
2
5
3
#S1
#S2
(Note2) #S3
#S2
(Note2) #S3
#S4
(Note2)
(Note2)
#S3
#S4
(Note2)
#S4
(Note2)
4
ns
DSC-W520
2-4
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
2-1-2. MAIN FRAME SECTION
ns: not supplied
DISASSEMBLY
51
X-2581-276-1 FRAME ASSY (S), MAIN (SILVER)
51
X-2581-277-1 FRAME ASSY (B), MAIN (BLACK)
51
X-2581-278-1 FRAME ASSY (R), MAIN (RED)
52
4-281-028-01 BRACKET,
LCD
53
1-858-625-11
SPEAKER (1.3CM) (Note1)
54
A-1821-754-A STROBOSCOPE
BLOCK
ASSY
55
4-281-023-01 SHEET
(BLACK)
56
4-281-022-01 SHEET
(TRANSPARENT)
0 F401
1-576-363-21
FUSE, MICRO (1005 TYPE) (1A/30V)
#S5
3-288-943-01 SCREW_TP_1.4_3_A_0.2_D=2.5
6
#S5 X 1
→ Unsolder
7
#S5 X 3
Note
1. Remove in numerical order (
6
to
7
) in the left figure.
Top View
#S5
Solder
Front View
#S5
Note1: Refer to “Assembly-2: Routing Method of the Speaker Lead
Wire” when you assemble.
Note2: Be sure to connect the flexible board of the Lens Block to
the Main Board before assembling the Main Board and Lens
Block to the Main Frame Assy.
Block to the Main Frame Assy.
6
54
56
6(Claw)
53
(Note1)
#S5
#S5
#S5
7(Claw)
#S5
52
Solder
F401
6(Solder)
7(Claw)
7
51
Main Board / Lens Block Section
(See page 2-5)
(Note2)
(See page 2-5)
(Note2)
ns
55
Click on the first or last page to see other DSC-W520 service manuals if exist.