Sony DSC-W520 Service Manual ▷ View online
DSC-W520
3-8
3-4. Assembly
This cut portion should be located
around only this phase.
around only this phase.
Front view of the
front barrel part
front barrel part
Lever
5. After the BARRIER ASSY has been replaced with a new one, return the process from 4. to 1. according to the
process flow.
Note-1: Align the lever with the dedicated cut portion as shown in the figure.
Note-2: Attach the COSMETIC RING ASSY with small amounts of strong adhesive (*).
(*) Commercially available. Do not use any instant glue.
Assembly-2:
Routing Method of
the Speaker Lead Wire
the Speaker Lead Wire
Speaker lead wire
Assembly-1:
Putting position of the Retainer
Boss
LCD Bracket
Retainer
3-1. Cut the Microphone lead wire as shown below.
3-2. Strip off the coating of the Microphone lead wire as shown below.
3-3. Perform the preliminary solder dipping on the core of
the Microphone lead wire as shown below.
Cut
12mm (±3mm)
Microphone lead wire
Preliminary solder dipping
Strip off
1.5mm (±0.5mm)
Assembly-3:
Assembling Method of the Microphone
DSC-W520
3-9
DRIVE CAM BARREL
The shutter assy
To this cam
groove
groove
Rear view of Aligning
The phase of drive
gear portion
gear portion
Assembled
(The inner-block_4)
(The inner-block_4)
1. Align the shutter assy with the DRIVE CAM BARREL as shown in the figure.
2. Assemble the shutter assy and the DRIVE CAM BARREL by turning the shutter assy approx. 120 degree in the arrow
direction to move it to the position shown below.
3-5. Assembling
Front view of the
front barrel part
front barrel part
The inner-block_4
The phase of drive
gear portion
gear portion
The phase of
FPC portion
FPC portion
This cut portion should be located
around only this phase.
around only this phase.
To this cam
groove
groove
Aligned
The front
barrel part
barrel part
Assembled
(The inner-block_3)
(The inner-block_3)
The inner-block_4
3. Align the front barrel part with the inner-block_4 as shown in the figure.
4. Assemble the front barrel part and the inner-block_4 by turning the front barrel part in the arrow direction to move it to
the position shown below.
the position shown below.
DSC-W520
3-10
The phase of
FPC portion
FPC portion
The inner-block_3
LINEAR
GUIDE
BARREL
GUIDE
BARREL
The only thin projection
should be located
around this phase.
should be located
around this phase.
Assembled
(The inner-block_2)
(The inner-block_2)
The inner-block_2
2ND OUTER
BARREL
BARREL
Rear view of
2ND OUTER
BARREL
2ND OUTER
BARREL
The only thin projection
should be located
around this phase.
should be located
around this phase.
The phase of
FPC portion &
thin projection
FPC portion &
thin projection
5. Assemble the LINEAR GUIDE BARREL and the inner-block_3 as the inner-block_2 as shown in the figure.
6. Align the 2ND OUTER BARREL with the inner-block_2 as shown in the figure.
The inner-block_2
2ND OUTER
BARREL
BARREL
The inner-block_1
Projection
Moved
Before move
7. Assemble the 2ND OUTER BARREL and the inner-block_2 as the inner-block_1 as shown in the figure.
8. Turn the projection of the inner-block_1 a little in the arrow direction to move it to the position shown below.
DSC-W520
3-11
The phase of
FPC portion
FPC portion
The inner-block_1
FIXED BARREL
Placed
9. While aligning the inner-block_1 and the FIXED BARREL as the illustrated phase relation, place the inner-block_1 into
the FIXED BARREL.
10. Attach a long gear such as Gear driver (J6082750A) or a removed ZOOM LONG GEAR.
Then turn the long gear counterclockwise to set the block in the TELE end state.
Nut
To around here
Passed
11. Pass the FPC through the hole.
12. Turn the nut of FOCUSING SHAFT ASSY in the arrow direction to move it to around the illustrated position.
Click on the first or last page to see other DSC-W520 service manuals if exist.