Sony DSC-W515PS Service Manual ▷ View online
DSC-W515PS
1-7E
1-7-2. Inspection When Cam Tube Block Assy Or Straight Tube Lubricated Assy Is Replaced
Focus check
1
1
Preparation
• Camera installed re-assemble lens.
• Chart (Printed PDF file at the same magnification) (Refer to <Reference>)
• Tripod
• Mirror (ex. CD)
• Memory card
• PC
2
Shoot setting
(1) Paste the chart.
• Chart should be on the flat wall.
• Illuminance level in the chart should be the same.
• Make the tripod’s height and the center of the chart to the same height.
• Enough space needed for shooting.
(2) Set the camera.
• Set [P] mode
• Set Image Size Maximum [12M]
• Set ISO lowest level
• Set Steady Shot [OFF]
• Set Flash [OFF]
(3) Set the camera on a tripod.
(4) Adjust the position of the camera and the chart.
1. Set the zoom position of the camera at Wide end.
2. Attach the mirror onto the center of the chart.
* The mirror should not tilt on the chart.
3. Set the camera to display the chart on LCD like in the following picture.
4. Adjust the camera position to the center of the chart.
* Adjust the tripod height and the position (Lateral direction).
5. Adjust the camera angle to the frame of the chart with tripod.
Remove the mirror.
3
Shooting
(1) Set [Self-Timer]
(2) Shot
4
Check the shot image.
(1) Check the shot image on PC.
100% Display (Display at the same magnification of its Pixel.)
Compare the image with the sample you set.
No extreme focus blurring
It should be distinguished the black and white by the sharpness between them.
If it is in NG level, replace the lens unit.
<Reference>
• How to Print the Chart
Print “Forcus-Chart_A3.pdf” with printer.
Print at the same magnification (It means 100 % size).
Check the settings of printer to print in proper size.
• Check of chart size.
Make charts together and check if the size of charts is the following size.
* The chart consists of 2 pcs.
1-7. FINAL INSPECTION
1-7-1. Confirm There Is No Fault In Actual Motion/Actual Screen
1
2
Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
3
Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45°)
No abnormal sound must be heard during the operation.
4
Appearance condition
5
Lower oblique 45°
Upper oblique 45°
Inspect it as follows when you exchange parts in the lens block.
Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45°)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
The barrier must be opened and closed fully, free from a sticking in the midway.
Scratches or stains must not be noticeable, except that the customer permits them.
Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.
Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.
Lens at WIDE end
Full stroke check
Lens at TELE end
Upward
Horizontal
Downward
DSC-W515PS
2-1
7�
LCD Bracket Assy
8�
LCD Module
5�
Ornamental Belt (R)
qa�
Lens Block Section
[Disassembly]
[Exploded View]
2�
Front Cover Assy
4�
Ornamental Belt (L)
0�
ST Board
3�
Top Cover Assy
qs�
Main Board
1�
Rear Cover Assy
qf�
SW Board
qd�
Main Frame Assy
9�
Capacitor Cover
Link
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
View Position
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original one.
• Items marked “*” are not stocked since they are seldom required for routine service. Some
delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Due to standardization, replacements in the parts list may be different from the parts speci-
fied in the diagrams or the components used on the set.
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
Les composants identifiés par une marque
0
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
When indicating parts by reference
number, please include the board name.
ACCESSORIES
ASSEMBLY
DISCHARGING OF THE CHARGING CAPACITOR
Right View
Left View
Front View
Bottom View
Top View
Back View
DSC-W515PS
2-2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, do not pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, do not press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
The charging capacitor is charged up to the maximum 310 V
potential.
There is a danger of electric shock by this high voltage
when the capacitor is handled by hand. The electric shock
is caused by the charged voltage which is kept without dis-
charging when the main power of the unit is simply turned
off. Therefore, the remaining voltage must be discharged as
described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end
of a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
DISCHARGING OF THE CHARGING CAPACITOR
Cut and remove the part of gilt
which comes off at the point.
(Be careful of some
pieces of gilt may be left inside)
Wrap insulating tape.
Note: High-voltage cautions
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points with the short jig about 10 seconds.
To avoid the spark with the metal plate, wrap the short jig with the
insulation tape.
Short-circuit between the two points with the short jig about 10 seconds.
To avoid the spark with the metal plate, wrap the short jig with the
insulation tape.
Temporarily peel off the sheet
R:1 k/1 W
(Part code: 1-215-869-11)
ST Board
DSC-W515PS
2-3
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
DISASSEMBLY
1
X-2580-714-1 COVER ASSY, FRONT
2
4-273-596-01 BELT (L), ORNAMENTAL
3
X-2580-718-1 COVER ASSY, TOP
4
X-2580-713-1 COVER ASSY, REAR
5
4-273-595-01 BELT (R), ORNAMENTAL
#S1
4-273-576-01 SCREW_M_1.4_3.5_SVR_AB
#S2
4-273-578-01 SCREW_M_1.4_2.5_SVR_AB
#S3
4-273-593-01 SCREW_M_1.4_2.0_SVR_AB
#S4
4-273-594-01 SCREW_TP_1.4_4.5_SVR_AB
1
#S1 X 6 → #S2 X 1
2
#S1 X 2
3
#S3 (
3
) → Raise the SW Board → #S4
6
1. Remove to numerical order (
1
to
6
) in the left figure.
DISCHARGING OF THE CHARGING CAPACITOR
#S2
#S1
#S1
#S1
Bottom View
Left View
Right View
#S1
Bottom View
#S3
#S4
Back View
Back View
SW Board
6
#S1
#S1
#S2
#S3
#S4
#S1
#S1
LCD Section
(See page 2-4)
2
4
3
3
4
1
5
5
2
1
2(Claw)
4(Claw)
4(Claw)
1(Claw)
3(Claw)
2(Claw)
3
Click on the first or last page to see other DSC-W515PS service manuals if exist.