Sony DSC-W390 (serv.man2) Service Manual ▷ View online
DSC-W390_L2
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
AC-
DIS-
IDENTIFYING PARTS
Link
ACCESSORIES
DISCHARGING OF THE CHARGING CAPACITOR
• Abbreviation
CH :
CH :
Chinese
model
CND : Canadian model
ASSEMBLY
SY
-237
q;
Lens Block Section
[Disassembly]
[Exploded
View]
• CD-773 Flexible Board
qs
Upper Cabinet Section
[Disassembly]
[Exploded
View]
•
ST-224
Board
1
Rear Cabinet Assy
qa
Front Cabinet Assy
4
LCD
5
Main Frame
2
SW-561 Board
qd
SY-237 Board
qf
BT Holder Assy
3
Side Cabinet (L)
7
Tripod Screw
8
Charging Capacitor
(MA-461 Flexible Board)
9
Side Cabinet (R)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original
• -XX, -X mean standardized parts, so they may have some differences from the original
one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not sup-
plied.
• Due to standardization, replacements in the parts list may be different from the parts
specified in the diagrams or the components used on the set.
• Color Indication of Appearance Parts
Example:
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
The components identified by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
le numéro spécifié.
Right View
Left View
Front View
Bottom View
Top View
Back View
View Position
Ver. 1.3 2010.05
DSC-W390_L2
2-2
The charging capacitor (C901) of the MA-461 Flexible flexible
board is charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
board is charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked
of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, don’t press down at wire of con-
nector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
DISCHARGING OF THE CHARGING CAPACITOR (C901)
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
Short-circuit between two points
with the short jig about 10 seconds.
R:1 k
Ω/1 W
(Part code: 1-215-869-11)
C901
MA-461 Flexible
Board
Board
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Wrap insulating tape.
DSC-W390_L2
2-3
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
4-168-194-01
CABINET (L (680)), SIDE (SILVER)
1
4-168-194-11
CABINET (L (680)), SIDE (BLACK)
2
1-837-002-11
CABLE, FLEXIBLE FLAT (FFC-216)
3
A-1731-538-A SW-561 BOARD, COMPLETE
4
4-167-835-01
DIAL (670), MODE
5
4-167-836-01
PLATE (670), MODE
6
4-167-839-01
SHEET (670), BRACKET ADHESIVE
* 7
4-167-840-01
BRACKET (680), STRAP
8
X-2541-691-1 CABINET (REAR) ASSY (680C)
#65
2-635-591-01
SCREW (M1.4), NEW TRUSTAR P2 (Note)
#147
2-662-396-41
SCREW (M1.4), NEW, TRUSTAR, P2 (Note)
1. Remove to numerical order (
1
to
3
) in the left figure.
DISASSEMBLY
1
#65 / #147 X 7
Screw
#65: M1.4 X 3.5
(Silver)
2-635-591-01
2-635-591-01
3.5
1.4
2
3
1
2
3
1
8
LCD Section
(See page 2-4)
(See page 2-4)
4
5
6
7
2
(Boss)
#65
#147
(Note)
#147
(Note)
#65
#147
(Note)
#147
(Note)
#65
#147
(Note)
#147
(Note)
#65
#147
(Note)
#147
(Note)
#65
Right View
Left View
Bottom View
#147
#65
#147
#147
#65
#147
#147
3.5
1.4
#147: M1.4 X 3.5
(Black)
2-662-396-41
2-662-396-41
Note
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
#65 (Silver)
SILVER
#147 (Black)
BLACK
Cabinet's Color
Table 2-1
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
Note:
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2010.01
DSC-W390_L2
2-4
2-1-2. LCD SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
* 51
4-168-185-01 SCREW (670), TRIPOD
52
4-168-193-01
CABINET (R (680)), SIDE (SILVER)
52
4-168-193-11
CABINET (R (680)), SIDE (BLACK)
* 53
4-168-187-01
SHEET (670), INSULATING
54
1-880-292-11
MA-461 FLEXIBLE BOARD
55
4-168-197-01
SPACER (670), LCD
* 56
4-168-191-01
FRAME (680), MAIN
57
4-168-192-01
SHEET (680), LCD INSULATING
58
4-167-569-01
CUSHION (680), LCD (Note)
59
4-167-568-01
WINDOW (680), LCD (Note)
0 C901
1-116-440-11
CAP, ELECT
63uF
99%
315V
LCD901 1-802-983-11 LCD
MODULE
(LMS300GF07)
53
54
57
55
Main Section
(See page 2-5)
(See page 2-5)
58
59
5
(Boss)
56
8
52
51
4
LCD901
(Note)
(Note)
7
C901
4
6
5
9
DISCHARGING OF THE CHARGING CAPACITOR
1. Remove to numerical order (
4
to
9
) in the left figure.
DISASSEMBLY
6
Note
Note: Refer to “Assembly-4” when you install Attaching Method
of LCD cushion (680) and LCD window (680).
4
LCD Insulating Sheet (680) (
4
)
Click on the first or last page to see other DSC-W390 (serv.man2) service manuals if exist.