DOWNLOAD Sony DSC-W290 (serv.man2) Service Manual ↓ Size: 4.33 MB | Pages: 64 in PDF or view online for FREE

2-8

DSC-W290_L2

2 

Remove adhesive agent remaining on the side surface of the group-1 frame.

3 

Apply adhesive agent to two places of the first convex on the side surface in 3-4 o'clock and 9-10 o'clock directions.

 

 Super X (white) or equivalents

 

 2-3 cubic millimeters per place

4 

Install new Ornamental Ring (A)

 

 When the Ornamental Ring (A) passed the second convex, if extra adhesive agent remains on the end surface of the ring, 

 

wipe it off and push in the ring until it is stopped.

5 

Wait for the adhesive agent to harden.

 

 About 20 minutes

1 

With three claws fitted in position, install the Barrier Assy.

Convex 

Adhesive agent

Adhesive agent

Ornamental Ring (A)

Barrier Assy

Claws

2-9

DSC-W290_L2

1

  Remove one screw.

2

 Break 

solders.

3

  Remove the Zoom Gear Block.

4

  Remove the Naruto Gear.

3

  Install the Zoom Gear Block after matching the position of boss.

4

  Solder the flexible board of Zoom Gear Block.

5

  Tighten one screw.

 * 

Tightening torque = 0.098 

±

 0.01N 

•

 m (1.0 

±

 0.1kgf 

•

 cm)

1

  Confirm the lens barrel is stored.

2

  Confirm the direction of the Naruto Gear and install it.

1

1

 Screw

3

 Zoom Gear Block

3

 Zoom Gear Block

2

 Solders

5

 Screw

Boss

4

 Solders

4

 Naruto Gear

2

 Naruto Gear

Adjust convex part to the CCD side.

2-10E

DSC-W290_L2

1

Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45˚)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.

2

Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.

3

Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45˚)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.

4

Appearance condition
Scratches or stains must not be noticeable, except that the customer permits them.

5

Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.

Lens at TELE end

Upward

Downward

Horizontal

Upper oblique 45˚

Lower oblique 45˚

Lens at WIDE end

Turn power on.
After the check,
turn power off.

Full
stroke
check

DSC-W290_L2

Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.

1

 

Apply LCD cushion (320) adjusting the cut off portion as shown in the figure.

 

And peel off the release paper of LCD cushion (320).

2

 

Attach Cabinet (Rear) Assy (320) to set.

      And attach LCD window (320).

Note: 
After installing LCD window(320), 
check whether LCD cushion (320)
overflowed into the screen. 

LCD Cushion (320)

LCD

Cabinet (Rear) Assy (320)

Release paper

LCD Cushion (320)

Screen

LCD Window (320)

Note:
Do not apply LCD cushion (320)
peeled off once.
On replacing, use the new one.

Note:
Align corner of LCD cushion (320) with corner of LCD.

corner

corner

Note: 
Blow the air 
before attaching.
Be sure to keep
away from dust.