Sony DSC-W210 / DSC-W215 (serv.man2) Service Manual ▷ View online
2-10
DSC-W210/W215_L2
q;
Molds
4
Screw
7
Screw
3
Optical Stepping Motor
1
Solders
8
Zoom Gear Block
6
Lens Rear Block
Check if the hook fits with the shaft
Check if the shaft fits with the groove.
2
Check the state of each part
Lens Rear Block
Installation
1
Install the lens flexible board with four solders.
2
Referring to the following figure, check each part state of lens rear block.
3
Install
Optical
Stepping
Motor.
4
Tighten one screw.
*
Tightening torque = 0.049
±
0.01N
•
m (0.5
±
0.1kgf
•
cm)
5
Rotate the gear of lens barrel in arrow direction to extend the lens.
6
Check the inside of lens barrel and the lens for dust or stain, and then install the lens rear block.
7
Tighten three screws.
*
Tightening torque = 0.049
±
0.01N
•
m (0.5
±
0.1kgf
•
cm)
8
Install Zoom Gear Block by referring to the installation 4 to 6 in "2-5-1. Zoom Gear Block Replacing Method".
9
Install the lens flexible board with six solders.
q;
Assemble the lens flexible board with the mold of Lens Block.
qa
Engage the lens flexible board with the claw.
5
qa
Claw
9
Solders
2-11E
DSC-W210/W215_L2
2-5-3. FINAL INSPECTION (NO FAULT IN ACTUAL MOTION/ACTUAL SCREEN)
1
Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45
˚
)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
2
Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
3
Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45
˚
)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
No abnormal sound must be heard during the operation.
4
Appearance condition
Scratches or stains must not be noticeable, except that the customer permits them.
Scratches or stains must not be noticeable, except that the customer permits them.
5
Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.
The lens condition must not be worse than that when the camera was received from the customer.
Lens at TELE end
Upward
Downward
Horizontal
Upper oblique 45˚
Lower oblique 45˚
Lens at WIDE end
Turn power on.
After the check,
turn power off.
After the check,
turn power off.
Full
stroke
check
stroke
check
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2009.02
HELP
DSC-W210/W215_L2
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
HELP01
1
Apply LCD cushion (060) adjusting the cut off portion as shown in the figure.
And peel off the release paper of LCD cushion (060).
2
Attach LCD window (060) to Cabinet (Rear) Assy (060).
3
Attach Cabinet (Rear) Assy (060) to LCD Frame (060).
And remove Cabinet (Rear) Assy (060) except for the LCD window (060).
Note:
After installing the LCD window(060),
check whether the LCD cushion (060)
overflowed into the screen.
After installing the LCD window(060),
check whether the LCD cushion (060)
overflowed into the screen.
ATTACHING METHOD OF LCD CUSHION (060), LCD WINDOW (060)
LCD Cushion (060)
LCD
LCD Frame (060)
LCD Window (060)
LCD Window (060)
LCD Window (060)
Cabinet (Rear) Assy (060)
Cabinet (Rear)
Assy (060)
Assy (060)
Release paper
LCD Cushion (060)
Cabinet (Rear)
Assy (060)
Assy (060)
Screen
Note:
Do not apply LCD cushion (060)
peeled off once.
On replacing, use the new one.
Do not apply LCD cushion (060)
peeled off once.
On replacing, use the new one.
Note:
Align corner of LCD
cushion (060) with
corner of LCD.
Align corner of LCD
cushion (060) with
corner of LCD.
Note:
Bring the top and bottom side
of the cabinet (rear) assy (060).
Bring the top and bottom side
of the cabinet (rear) assy (060).
Note:
Blow the air
before attaching.
Be sure to keep
away from dust.
Blow the air
before attaching.
Be sure to keep
away from dust.
CutOut
HELP
DSC-W210/W215_L2
HELP02
HELP03
HOW TO FOLD FPC-007 FLEXIBLE BOARD
Mountain Fold
Mountain Fold
Balley Fold
FPC-007 Flexible
Board
Board
HOW TO ARRANGE LCD FLEXIBLE BOARD
Balley Fold
Flexible Board
(Back Light)
(Back Light)
Flexible Board
(LCD Unit)
(LCD Unit)
Flexible Board
Solders
SW-543 Board
LCD Module
LCD Module
Hole
LCD Frame (060)
Click on the first or last page to see other DSC-W210 / DSC-W215 (serv.man2) service manuals if exist.