DOWNLOAD Sony DSC-W210 / DSC-W215 Service Manual ↓ Size: 1.5 MB | Pages: 26 in PDF or view online for FREE

DSC-W210/W215_L3

The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part num-
ber specified.

Les composants identifiés par une
marque  0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.

Photo: DSC-W210/Silver

US Model

Canadian Model

AEP Model

UK Model

E Model

Australian Model

Chinese Model

Korea Model

Argentine Model

Brazilian Model

2009E0800-1

  © 2009.05

DSC-W210/W215_L3

Model

Destination

Color Variation

DSC-W210

US, CND, AEP, UK, E, 

AR, KR, AUS, CH, BR

DSC-W215

CND, AEP, UK, BR

Silver, Black, Green, Pink

Black

Soft carrying case
(accessories supplied)

• Abbreviation

AR

: Argentine model

AUS : Australian model
BR

: Brazilian model

CH

: Chinese model

CND : Canadian model
KR

: Korea model

—3 —

DSC-W210/W215_L3

0

0

1.

Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.

2.

Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.

3.

Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.

4.

Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.

5.

Check the B+ voltage to see it is at the values specified.

6.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

0

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40

°C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350

°C.

Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

— 4 —

CAUTION

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.

1-1

DSC-W210/W215_L3

The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)

When replacing the SY-215 board, erase the data in internal memory of the board before replacement.

When replacing the SY-215 board, execute formatting and initialize the internal memory after replacement.

Copies all images in the internal memory to a “Memory Stick Duo” media.

1

Insert a “Memory Stick Duo” media having sufficient free capacity.

2

Select [Copy] with v/V on the control button, then press z.
The message “All data on internal memory will be copied” appears.

3

Select [OK] with v, then press z.
Copying starts. 

Select [Cancel] in step 3, then press z.

  Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little 

remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.

  You cannot select images to copy.

  The original images in the internal memory are retained even after copying. To delete the contents of the 

internal memory, remove the “Memory Stick Duo” media after copying, then format the internal memory 
([Format] in [Internal Memory Tool]). 

  A new folder is created on the “Memory Stick Duo” media and all the data will be copied to it. You 

cannot choose a specific folder and copy images to it.

  The 

 (Print order) marks on the images are not copied.

z

 

z

 

z

 

z

 

z

 

This item does not appear when a “Memory Stick Duo” media is inserted in the camera.

Formats the internal memory.

  Note that formatting permanently erases all data in the internal memory, including even protected images.

1

Select [Format] with v/V on the control button, then press z.
The message “All data on internal memory will be erased” appears.

2

Select [OK] with v, then press z.
Formatting starts.

Select [Cancel] in step 2, then press z.

z

 

When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATON DATA WRITE”.

When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data.
The data getting for this model is as follows.

• USB SERIAL No.

The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.