Sony DSC-W130 (serv.man2) Service Manual ▷ View online
2-10
DSC-W130_L2
Check if the hook fits with the shaft
Check if the shaft fits with the groove.
5
qa
Claw
0
Molds
4
Screw
7
Screw
3
Optical Stepping Motor
2
Check the state of each part
1
Solders
9
Connector
8
Zoom Gear Block
6
Lens Rear Block
Lens Rear Block
Installation
1
Install the lens flexible board with four solders.
2
Referring to the following figure, check each part state of lens rear block.
3
Install Optical Stepping Motor.
4
Tighten one screw.
*
*
Tightening torque = 0.049
±
0.01N
•
m (0.5
±
0.1kgf
•
cm)
5
Rotate the gear of lens barrel in arrow direction to extend the lens.
6
Check the inside of lens barrel and the lens for dust or stain, and then install the lens rear block.
7
Tighten three screws.
*
*
Tightening torque = 0.049
±
0.01N
•
m (0.5
±
0.1kgf
•
cm)
8
Install Zoom Gear Block by referring to the installation 4 to 6 in "2-5-1. Zoom Gear Block Replacing Method".
9
Connect the connector of lens flexible board.
0
Assemble the lens flexible board with the mold of Lens Block.
qa
Engage the lens flexible board with the claw.
2-11E
DSC-W130_L2
2-5-3. FINAL INSPECTION (NO FAULT IN ACTUAL MOTION/ACTUAL SCREEN)
1
Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
2
Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
3
Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
4
Appearance condition
Scratches or stains must not be noticeable, except that the customer permits them.
Scratches or stains must not be noticeable, except that the customer permits them.
5
Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.
The lens condition must not be worse than that when the camera was received from the customer.
Lens at TELE end
Lens at WIDE end
Upward
Downward
Horizontal
Upper oblique 45˚
Lower oblique 45˚
Full stroke check
DSC-W130_L2
HELP
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
HELP 1:
LCD Window Adhesive Sheet Kit
HELP 3:
LCD Insulating Sheet
LCD Insulating Sheet
LCD Insulating Sheet
Hole
Hole
- Front Side -
- Rear Side -
HELP 2:
LCD Flexible Fixed Sheet
LCD Flexible Fixed Sheet
LCD Flexible Board
LCD Frame
LCD Window Adhesive Sheet Kit must use only
the part of LCD window edge.
Please discard other parts.
the part of LCD window edge.
Please discard other parts.
Discard parts
Paste parts
LCD Window Adhesive Sheet Kit
DSC-W130_L2
HELP
Tape (AF)
Tape (AF)
HELP 4:
Tape (AF)/Capacitor Protection Sheet
Capacitor Protection Sheet
HELP 5:
BT Terminal Harness
BT Terminal Harness
BT Holder Mold
BT Holder
BT901 (Red)
BT902 (White)
BT903 (Black)
SY-190 Board
Click on the first or last page to see other DSC-W130 (serv.man2) service manuals if exist.