Sony DSC-W130 (serv.man2) Service Manual ▷ View online
2-6
DSC-W130_L2
2-3. PRECAUTIONS WHEN HOLDING THE LENS BLOCK
•
Hold the Lens Block at the center of both sides.
•
Do not hold the following part.
Hold here.
Lens Flexible Board
OVF
OVF Cam Plate
Optical Stepping Motor
∗
Very weak
Zoom Motor
Lens Barrel
Focus Lens
Lens Barrier
∗
Very weak
2-7
DSC-W130_L2
2-4. BARRIER ASSY REPLACING METHOD
3
Peel off release papers of Barrier Tapes.
4
Install Ornamental Ring A and press it lightly.
Installation
1
Affix two Barrier Tapes to Barrier Assy.
Note:
The tape must not be wrinkled.
2
With four claws fitted in position, install the Barrier Assy.
5
Remove Barrier Assy by disengaging four claws.
Ornamental Ring A
Ornamental Ring A
Barrier Assy
Barrier Assy
Barrier Assy
Barrier Tapes
Barrier Tape
Barrier Tape
A
Removal
1
Turn on the power switch and extend the lens.
2
Detach the battery.
3
Pour a solvent such as alcohol from two places A to the tweezers or a needle shown below into a gap of Ornamental Ring A.
4
Remove while turning the Ornamental Ring A right and left.
Solvent
Claws
Only one hook has
different shape.
different shape.
Claws
Claws
Claws
Tweezers
2-8
DSC-W130_L2
2-5. LENS MOTOR REPLACING METHOD
Replace the parts if the following events appear when the power switch is turned on.
1
"Turn off and on the power" is displayed without performing the zoom operation.
Replace Zoom Gear Block if a damage of lens barrel due to a drop of camera is not found.
(See "2-5-1. Zoom Gear Block Replacing Method")
Replace Lens Block if such replacement does not improve the failure.
(See "2-5-1. Zoom Gear Block Replacing Method")
Replace Lens Block if such replacement does not improve the failure.
2
"Turn off and on the power" is displayed after the "lens zooming in and out" operation over its full stroke was repeated
3 times.
3 times.
Replace Optical Stepping Motor. (See "2-5-2. Optical Stepping Motor Replacing Method")
Replace Lens Block if such replacement does not improve the failure.
Replace Lens Block if such replacement does not improve the failure.
2-5-1. Zoom Gear Block Replacing Method
Removal
1
Remove one screw.
2
Remove Zoom Gear Block upward.
3
Remove Naruto Gear (S).
4
Disengage two claws A and B in this order to remove FG Plate Spring.
Note:
The FG Plate Spring cannot be reused.
5
Remove two sensors on the lens flexible board.
6
Break two solders, and remove the lens flexible board.
Installation
1
Confirm the direction of Zoom Gear Block, and install the lens flexible board with two solders.
2
Pass the lens flexible board through the mold of Zoom Gear Block to install two sensors.
3
Engage two claws A and B in this order to install FG Plate Spring.
6
Install Naruto Gear (S).
6
With four bosses fitted in position, install Zoom Gear Block.
6
Tighten one screw.
*
*
Tightening torque = 0.049
±
0.01N
•
m (0.5
±
0.1kgf
•
cm)
1
Screw
6
Screw
2
Zoom Gear Block
5
Zoom Gear Block
Zoom Gear Block
Zoom Gear Block
Front Side
Rear Side
Bosses
Bosses
Mold
Mold
4
FG Plate Spring
3
FG Plate Spring
5
Sensors
2
Sensors
6
Solders
1
Solders
3
Naruto Gear (S)
4
Naruto Gear (S)
Claw
A
Claw
A
Claw
B
Claw
B
2-9
DSC-W130_L2
1
Claw
4
Screws
6
Screw
7
Optical Stepping Motor
8
Solders
2
Connector
3
Zoom Gear Block
5
Lens Rear Block
2-5-2. Optical Stepping Motor Replacing Method
Removal
1
Disengage the lens flexible board from the claw.
2
Disconnect the connector of the lens flexible board.
3
Remove Zoom Gear Block by referring to the removal 1 to 3 in "2-5-1. Zoom Gear Block Replacing Method".
4
Remove three screws.
5
Remove the lens rear block.
6
Remove one screw.
7
Remove Optical Stepping Motor.
8
Break four solders to remove the lens flexible board.
Click on the first or last page to see other DSC-W130 (serv.man2) service manuals if exist.