DOWNLOAD Sony DSC-W110 / DSC-W115 (serv.man2) Service Manual ↓ Size: 5.64 MB | Pages: 69 in PDF or view online for FREE

2-8

DSC-W110/W115_L2

1

"Turn off and on the power" is displayed without performing the zoom operation.

Replace Zoom Gear Block if a damage of lens barrel due to a drop of camera is not found.
(See "2-5-1. Zoom Gear Block Replacing Method")
Replace Lens Block if such replacement does not improve the failure.

2

"Turn off and on the power" is displayed after the "lens zooming in and out" operation over its full stroke was repeated 
3 times.

Replace Optical Stepping Motor. (See "2-5-2. Optical Stepping Motor Replacing Method")
Replace Lens Block if such replacement does not improve the failure.

1

Remove one screw.

2

Remove Zoom Gear Block upward.

3

Remove Naruto Gear (S).

4

Disengage two claws A and B in this order to remove FG Plate Spring.

The FG Plate Spring cannot be reused.

5

Remove two sensors on the lens flexible board.

6

Break two solders, and remove the lens flexible board.

1

Confirm the direction of Zoom Gear Block, and install the lens flexible board with two solders.

2

Pass the lens flexible board through the mold of Zoom Gear Block to install two sensors.

3

Engage two claws A and B in this order to install FG Plate Spring.

4

Install Naruto Gear (S).

5

With four bosses fitted in position, install Zoom Gear Block.

6

Tighten one screw.
*

Tightening torque = 0.049 

±

 0.01N 

•

 m (0.5 

±

 0.1kgf 

•

 cm)

1

Screw

6

Screw

2

Zoom Gear Block

5

Zoom Gear Block

Zoom Gear Block

Zoom Gear Block

Front Side

Rear Side

Bosses

Bosses

Mold

Mold

4

FG Plate Spring

3

FG Plate Spring

5

Sensors

2

Sensors

6

Solders

1

Solders

3

Naruto Gear (S)

4

Naruto Gear (S)

Claw 

A

Claw 

A

Claw 

B

Claw 

B

2-9

DSC-W110/W115_L2

1

Claw

4

Screws

6

Screw

7

Optical Stepping Motor

8

Solders

2

Solders

3

Zoom Gear Block

5

Lens Rear Block

1

Disengage the lens flexible board from the claw.

2

Remove solders of the lens flexible board.

3

Remove Zoom Gear Block by referring to the removal 1 to 3 in "2-5-1. Zoom Gear Block Replacing Method".

4

Remove three screws.

5

Remove the lens rear block.

6

Remove one screw.

7

Remove Optical Stepping Motor.

8

Break four solders to remove the lens flexible board.

2-10

DSC-W110/W115_L2

Check if the hook fits with the shaft

Check if the shaft fits with the groove.

5

qa

 

Claw

0

 

Molds

4

 

Screw

7

 

Screw

3

 

Optical Stepping Motor

2

 

Check the state of each part

1

 

Solders

8

 

Zoom Gear Block

6

 

Lens Rear Block

Lens Rear Block

1

Install the lens flexible board with four solders.

2

Referring to the following figure, check each part state of lens rear block.

3

Install Optical Stepping Motor.

4

Tighten one screw.
*

Tightening torque = 0.049 

±

 0.01N 

•

 m (0.5 

±

 0.1kgf 

•

 cm)

5

Rotate the gear of lens barrel in arrow direction to extend the lens.

6

Check the inside of lens barrel and the lens for dust or stain, and then install the lens rear block.

7

Tighten three screws.
*

Tightening torque = 0.049 

±

 0.01N 

•

 m (0.5 

±

 0.1kgf 

•

 cm)

8

Install Zoom Gear Block by referring to the installation 4 to 6 in "2-5-1. Zoom Gear Block Replacing Method".

9

Solder the lens flexible board.

0

Assemble the lens flexible board with the mold of Lens Block.

qa

Engage the lens flexible board with the claw.

9

Solders

2-11E

DSC-W110/W115_L2

1

Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.

2

Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.

3

Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.

4

Appearance condition
Scratches or stains must not be noticeable, except that the customer permits them.

5

Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.

Lens at TELE end

Lens at WIDE end

Upward

Downward

Horizontal

Upper oblique 45˚

Lower oblique 45˚

Full stroke check