Sony DSC-W110 / DSC-W115 (serv.man2) Service Manual ▷ View online
1-8E
DSC-W110/W115_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-5. 内蔵メモリへデータを書き戻す方法
通常は,PCからカメラの内蔵メモリへデータを書き込むことはできない設定になっています。
基板交換後などに,内蔵メモリへデータを書き戻す場合には,この設定を一時的に変更する必要があります。
設定の変更には,書き込み許可ツール(WriteEnableTool.exe)を使用します。
書き戻し方法
1)
1)
カメラとPCをマスストレージ接続し,ドライバを“Sony Seus USB Driver”に切り替える。
2)
書き込み許可ツールとSeusEXを起動する。
3)
書き込み許可ツールの[Activate Write Enable Mode]ボタンをクリックする。
4)
設定の変更が終了すると,次のメッセージが表示されます。
5)
ドライバを元に戻して、カメラとPCをマスストレージ接続する。
6)
PCに読み出しておいたデータをカメラの内蔵メモリに書き込む。
7)
カメラとPCの接続を解除し,カメラの電源をOFFにする。
注意: カメラの電源をOFFにすることにより,書き込み許可の設定が解除されます。
2-1
DSC-W110/W115_L2
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE CHARGING CAPACITOR (C901)
The charging capacitor (C901) is charged up to the maximum
300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
Short-circuit between two points
with the short jig about 10 seconds.
C901
ST-180 Board
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
2-2
DSC-W110/W115_L2
2-1. IDENTIFYING PARTS
Cabinet (Front)
Cabinet (Rear)
LCD
Lens Block
⋅
CCD Block (CD-719 Flexible Board)
BT Holder Section
⋅
MC-189 Flexible Board
⋅
ST-188 Flexible Board
⋅
SY-188 Board
LCD Frame
⋅
SW-520 Board
⋅
SW-533 Flexible Board
Cabinet (Upper)
⋅
AF-112 Board
⋅
ST-180 Board
2-2-1. LCD SECTION
⋅
Cabinet (Rear)
⋅
LCD
2-2-2. FRONT SECTION
⋅
Cabinet (Front)
⋅
Lens Block
2-2-3. BT HOLDER SECTION
⋅
Cabinet (Upper) Block
⋅
SY-188 Board
- DISASSEMBLY FLOW -
2-3
DSC-W110/W115_L2
2-2. DISASSEMBLY
2-2-1. LCD SECTION
Follow the disassembly in the numerical order given.
1
Cabinet (Rear) (
1
-1 to
1
-6)
2
LCD (
2
-1 to
2
-17)
HELP
HELP
EXPLODED VIEW
HARDWARE LIST
1
-1 (#20)
1
-6
1
-5 (Boss)
1
-4
(Boss)
1
-2 (#20)
1
-3 (#20)
1
Cabinet (Rear)
2
-2 (#20)
2
-4 (#20)
2
-5 (#20)
2
-6 (#118)
2
-13
(Claw)
2
-7
(Claw)
2
-16
(Solder)
2
-15
2
-17
2
-14
(Claw)
2
-8
2
-9
2
-10
2
-11
2
-12
2
-1
2
-3
2
LCD
Front Section
(See Page 2-4)
HELP 1
HELP 2
HELP 3
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
Short-circuit between two points
with the short jig about 10 seconds.
C901
ST-180 Board
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
Click on the first or last page to see other DSC-W110 / DSC-W115 (serv.man2) service manuals if exist.