Sony DSC-U10 (serv.man4) Service Manual ▷ View online
DSC-U10
6-11
1.
HALL Adjustment
For detecting the position of lens iris, adjust the hall AMP gain
and offset.
and offset.
Mode
CAMERA
Subject
Not required
Measurement Point
Data of page: 10, address: 06
Adjustment Page
6F
Adjustment Address
58 to 5D and 68
Specified value 1
12 to 1A
Specified value 2
80 to 88
Note 1:
Check that the data of page: 60, address: 02 is “00”. If
not, press the RESET switch at the bottom of the set us-
ing a thin and long pin.
not, press the RESET switch at the bottom of the set us-
ing a thin and long pin.
Adjusting method:
Order Page Address
Data
Procedure
1
Perform “Data setting
during camera system
adjustment”
(Refer to page 6-10)
during camera system
adjustment”
(Refer to page 6-10)
2
60
01
6D
[Write]
(Note 2)
3
60
02
[Read]
Check the data changes
to “01”.
to “01”.
4
60
01
00
[Write]
Note 2:
The adjustment data will be automatically input to page:
6F, address: 58 to 5D and 68.
6F, address: 58 to 5D and 68.
Checking method:
Order Page Address
Data
Procedure
1
60
01
01
[Write]
2
10
06
[Read]
Check that the data
satisfied the specified
value 1.
satisfied the specified
value 1.
3
60
01
00
[Write]
4
60
01
03
[Write]
5
10
06
[Read]
Check that the data
satisfied the specified
value 2.
satisfied the specified
value 2.
Processing after Completing Adjustment:
Order Page Address
Data
Procedure
1
60
01
00
[Write]
2
Release “Data setting
during camera system
adjustment”
(Refer to page 6-10)
during camera system
adjustment”
(Refer to page 6-10)
DSC-U10
6-12
2.
Flange Back Adjustment
The inner focus lens flange back adjustment is carried out auto-
matically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
matically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
Preparations before adjustments:
1) Check that the center of Flange back adjustment chart meets
1) Check that the center of Flange back adjustment chart meets
the center of shot image screen.
2-1.
Flange Back Adjustment
Mode
CAMERA
Subject
Flange back adjustment chart
(2.0 m from the front of lens)
(Luminance: 300 to 400 lux)
(2.0 m from the front of lens)
(Luminance: 300 to 400 lux)
Measurement Point
Data of page: 6F, address: 24 and
3E
3E
Adjustment Page
6F
Adjustment Address
18 to 1D, 20 to 2B, 3E, 52 and 53
Specified value 1
00
Specified value 2
0A to 7F
Note 1:
Check that the data of page: 60, address: 02 is “00”. If
not, press the RESET switch at the bottom of the set us-
ing a thin and long pin.
not, press the RESET switch at the bottom of the set us-
ing a thin and long pin.
Adjusting method:
Order Page Address
Data
Procedure
1
Perform “Data setting
during camera system
adjustment”
(Refer to page 6-10)
during camera system
adjustment”
(Refer to page 6-10)
2
60
01
13
[Write]
3
60
01
15
[Write]
(Note 2)
4
60
02
[Read]
Check the data changes
to “01”.
to “01”.
5
6F
3E
[Read]
Check that the data
satisfied the specified
value 1.
satisfied the specified
value 1.
6
6F
24
[Read]
Check that the data
satisfied the specified
value 2.
satisfied the specified
value 2.
Note 2:
The adjustment data will be automatically input to page:
6F, address: 18 to 1D, 20 to 2B, 3E, 52 and 53.
6F, address: 18 to 1D, 20 to 2B, 3E, 52 and 53.
Processing after Completing Adjustment:
Order Page Address
Data
Procedure
1
60
01
00
[Write]
2
20
00
29
[Set]
3
20
01
29
[Write]
(Note 3)
4
Wait for 4 seconds.
5
Perform “Flange Back
Check”.
Check”.
Note 3:
At this time, the set is reset and the power is turns off
once and then on again. Accordingly, the message “Re-
ceive Packet Error” is displayed on the SEUS screen, and
the SEUS goes in “disconnect” state, but this is not a
trouble. Click
once and then on again. Accordingly, the message “Re-
ceive Packet Error” is displayed on the SEUS screen, and
the SEUS goes in “disconnect” state, but this is not a
trouble. Click
[Connect]
on the SEUS screen to restore
the “connected” state.
2-2.
Flange Back Check
Mode
CAMERA
Subject
Flange back adjustment chart
(2.0 m from the front of lens)
(Luminance: 300 to 400 lux)
(2.0 m from the front of lens)
(Luminance: 300 to 400 lux)
Measurement Point
Data of page: 6F, address: 15
Adjustment Page
6F
Adjustment Address
10 to 15
Specified value
00
Note 1:
Check that the data of page: 60, address: 02 is “00”. If
not, press the RESET switch at the bottom of the set us-
ing a thin and long pin.
not, press the RESET switch at the bottom of the set us-
ing a thin and long pin.
Checking method:
Order Page Address
Data
Procedure
1
“Flange Back Adjust-
ment” is completed.
ment” is completed.
2
00
01
01
[Set]
3
60
01
DD
[Write]
(Note 2)
4
60
02
[Read]
Check the data changes
to “01”.
to “01”.
5
6F
15
[Read]
Check that the data
satisfied the specified
value.
satisfied the specified
value.
Note 2:
The adjustment data will be automatically input to page:
6F, address: 10 to 15.
Processing after Completing Adjustment:
Order Page Address
Data
Procedure
1
60
01
00
[Write]
2
Release “Data setting
during camera system
adjustment”
(Refer to page 6-10)
during camera system
adjustment”
(Refer to page 6-10)
DSC-U10
6-13
3.
F No. Compensation
Adjust the dispersion of the lens iris every F number , and com-
pensate the exposure.
pensate the exposure.
Mode
CAMERA
Subject
Clear chart
(Standard picture frame)
(Standard picture frame)
Adjustment Page
6F
Adjustment Address
5E to 64
Note 1:
Check that the data of page: 60, address: 02 is “00”. If
not, press the RESET switch at the bottom of the set us-
ing a thin and long pin.
not, press the RESET switch at the bottom of the set us-
ing a thin and long pin.
Adjusting method:
Order Page Address
Data
Procedure
1
Perform “Data setting
during camera system
adjustment”
(Refer to page 6-10)
during camera system
adjustment”
(Refer to page 6-10)
2
Perform “Picture frame
setting”
(Refer to page 6-10)
setting”
(Refer to page 6-10)
3
60
01
BB
[Write]
(Note 2)
4
60
02
[Read]
Check the data changes
to “01”.
to “01”.
Note 2:
The adjustment data will be automatically input to page:
6F, address: 5E to 64.
6F, address: 5E to 64.
Processing after Completing Adjustment:
Order Page Address
Data
Procedure
1
60
01
00
[Write]
2
Release “Data setting
during camera system
adjustment”
(Refer to page 6-10)
during camera system
adjustment”
(Refer to page 6-10)
4.
Mechanical Shutter Adjustment
Adjust the close time and loss time every F number of mechanical
shutter, and compensate the exposure.
shutter, and compensate the exposure.
Mode
CAMERA
Subject
Clear chart
(Standard picture frame)
(Standard picture frame)
Measurement Point
Data of page: 60, address: AB
Adjustment Page
6F
Adjustment Address
B8 to D7
Specified value
00
Note 1:
Check that the data of page: 60, address: 02 is “00”. If
not, press the RESET switch at the bottom of the set us-
ing a thin and long pin.
not, press the RESET switch at the bottom of the set us-
ing a thin and long pin.
Adjusting method:
Order Page Address
Data
Procedure
1
Perform “Data setting
during camera system
adjustment”
(Refer to page 6-10)
during camera system
adjustment”
(Refer to page 6-10)
2
Perform “Picture frame
setting”
(Refer to page 6-10)
setting”
(Refer to page 6-10)
3
60
01
AD
[Write]
(Note 2)
4
60
02
[Read]
Check the data changes
to “01”.
to “01”.
5
60
AB
[Read]
Check that the data
satisfied the specified
value.
satisfied the specified
value.
Note 2:
The adjustment data will be automatically input to page:
6F, address: B8 to D7.
6F, address: B8 to D7.
Processing after Completing Adjustment:
Order Page Address
Data
Procedure
1
60
01
00
[Write]
2
Release “Data setting
during camera system
adjustment”
(Refer to page 6-10)
during camera system
adjustment”
(Refer to page 6-10)
DSC-U10
6-14
5.
Light Value Adjustment
Adjust the standard light value.
Mode
CAMERA
Subject
Clear chart
(Standard picture frame)
(Standard picture frame)
Measurement Point
Data of page: 10, address: 0C and
0D (2byte data) (Note 2)
0D (2byte data) (Note 2)
Data of page: 6F, address: 65
Adjustment Page
6F
Adjustment Address
65 to 67
Specified value 1
0FE0 to 1020
Specified value 2
38 to 48
Note 1:
Check that the data of page: 60, address: 02 is “00”. If
not, press the RESET switch at the bottom of the set us-
ing a thin and long pin.
not, press the RESET switch at the bottom of the set us-
ing a thin and long pin.
Note 2:
2byte data is upper 1byte data and lower 1byte data.
XX XX
Lower 1byte data (Page: 10, address: 0D)
Upper 1byte data (Page: 10, address: 0C)
Upper 1byte data (Page: 10, address: 0C)
Adjusting method:
Order Page Address
Data
Procedure
1
Perform “Data setting
during camera system
adjustment”
(Refer to page 6-10)
during camera system
adjustment”
(Refer to page 6-10)
2
Perform “Picture frame
setting”
(Refer to page 6-10)
setting”
(Refer to page 6-10)
3
60
01
0D
[Write]
(Note 3)
4
60
02
[Read]
Check the data changes
to “01”.
to “01”.
5
10
0C
[Read]
Read the data
(Upper 1byte).
(Upper 1byte).
6
10
0D
[Read]
Read the data
(Lower 1byte).
(Lower 1byte).
7
Check that the 2byte
data (Note 2) satisfied
the specified value 1.
data (Note 2) satisfied
the specified value 1.
8
6F
65
[Read]
Check that the data
satisfied the specified
value 2.
satisfied the specified
value 2.
Note 3:
The adjustment data will be automatically input to page:
6F, address: 65 to 67.
6F, address: 65 to 67.
Processing after Completing Adjustment:
Order Page Address
Data
Procedure
1
60
01
00
[Write]
2
Release “Data setting
during camera system
adjustment”
(Refer to page 6-10)
during camera system
adjustment”
(Refer to page 6-10)
6.
Mixed Color Cancel Data Input & Check
Correct the dispersion of Gr/Gb filter on CCD imager
Mode
CAMERA
Subject
Color bar chart
(Standard picture frame)
(Standard picture frame)
Adjustment Page
6F
Adjustment Address
B0 and B1
Input method:
Order Page Address
Data
Procedure
1
00
01
01
[Set]
2
6F
B0
00
[Write]
3
6F
B1
58
[Write]
4
00
01
00
[Set]
Checking method:
Order
Procedure
1
Shoot the color bar chart.
2
Capture the shot picture into the PC, and display the
picture on the PC screen.
picture on the PC screen.
3
Confirm that no line (horizontal streak) is present in
blue, red and magenta portions of the picture of color
bar chart displayed.
blue, red and magenta portions of the picture of color
bar chart displayed.
Click on the first or last page to see other DSC-U10 (serv.man4) service manuals if exist.