DOWNLOAD Sony DSC-TX5 (serv.man2) Service Manual ↓ Size: 3.36 MB | Pages: 41 in PDF or view online for FREE

DSC-TX5_L2

1-6

5.  Write the indicated value, leave for 1 minute, and check the pressure changes value is satisfied the following value by comparing between 

written indicated value and indicated value.

 

Specification value  1.00 kPa or less: OK

 

 

1.01 kPa or more: NG

 

150 sec

1 min

Measurement

Measure this changed value.
One minute later, it is OK
if the value within 1.00 kPa.

Measure between -2.0 to -8.0

-42.0 kPa

0 kPa

-45.0 kPa

-48.0 kPa

-2.0 kPa

FFF

-5.0 kPa

-8.0 kPa

1.  Confirm that there are not any dust on the BT lid and ML lid.
 

 

↓

 

Confirm that there is not any dust on the vacuum pad.

 

 

↓

 

Cover the microphone hole.

 

(Cover the microphone hole with silicon sheet for radiation(4-174-010-01 etc.) )

 

 

↓

 

Expand the suction time for 60 seconds, and perform the measurement again.

2.  Check the cabinet condition, and then perform the measurement again.
3.  If there is no improvement symptom, replace the cabinet (front) assy and the the cabinet (rear) assy, and perform the measurement 

again.

Opening/closing the battery/memory card cover or multi-connector cover may lead to degradation of the sealing gasket. We recommend 
that once a year you take the camera to your dealer, or to an authorized repair shop, to have the sealing gasket replaced for a fee.

Instruction manual recommends the periodic maintenance as shown above.
If there is the request for check, perform the procedure below.

•  Confirm that there is no air-leak.
•  Confirm that there is no strain on the exterior.
•  Confirm that there is not any dust on the BT lid and ML lid.
•  Replace the BT Lid packing and ML Assy.

1.  Remove the two fixed screws of BTL Packing.

 

2.  Remove the packing, and confirm that there is no scratch such as defect on the BTL Cover or BTL Packing Fixed Plate.

 

3.  Install the new BTL Packing. (also use the new screws)

Note: Be careful that there is no dust on the packing.

1.  Remove the fixed screw of ML Lid Assy.

 

DSC-TX5_L2

1-7

2.  Remove the ML Lid Assy by sliding it with holding down the R Push Rod.

Note: Be careful that do not flick the R Push Rod.

 

3.  Install the new ML Lid Assy to opposite procedure to removal.

LCD-PUSHER: J-6082-732-A

1.  Set the Cabinet (Rear) Assy on the LCD-pusher with aligning the each pin position.

2.  Hold down the cabinet (rear) assy to LCD-pusher with holding tightly on the four corners.

Note: • Hold tightly on the four corners without holding the touch panel.

 

 

• Push it on vertically with no leaning.

 

 

  If the load is applied at a point, LCD can be split.

 

3.  Check that there is no abrasion on the seal portion (white portion of touch panel circumference).

Note: It may cause the water leak that there is abrasion on the seal portion.

 

4.  Peel off the adhesive paper cleanly.

Note: • Do not touch the electricity-rubber.

 

 

• Do not left the adhesive material.

1.  Set the Cabinet (Rear) Assy on the LCD-pusher with aligning the each pin position.

 

DSC-TX5_L2

1-8

2.  Set the Waterproof Adhesive Sheet (TP) to cabinet (rear) assy aligning the each pin position.

 

3.  Remove the cabinet (rear) assy from LCD-pusher, and then attach the adhesive paper by tracing it from center to both ends.

Note: Confirm that there are no air bubble and wrinkle.

 

4.  Peel off the release paper of adhesive paper.

5.  Pass through the LCD flexible into the corresponding hole, and set it down into the cabinet (rear) assy.

Note: Do not touch the adhesive paper.

 

6.  Pass through the TP flexible board into the corresponding hole, and insert the TP Flexible Grommet into the deep.

7.  Attach the touch panel assy to cabinet (rear) assy with pushing the portion of adhesive paper tightly.

Note: • Trace from center to both ends.

 

 

• Attach it after confirming that there is no dust on the LCD and TP.

 

DSC-TX5_L2

1-9

When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.

When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data. 
The data getting for this model is as follows.

• USB SERIAL No.
• Angular Velocity Sensor Sensitivity adjustment
• Wide Limit adjustment
• AWB standard data input & check, Color reproduction check
• Strobe adjustment

Note: When you cannot read data from the former replace the same time SY-246 board and lens.

PMB Portable has been written in internal memory.
SY-246 board for service is supplied with written the PMB Portable.

The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.

When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor (SE401).
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity adj”.

Note: The sensor sensitivity of SE401 of SY-246 board is written only repair parts.

SE401

SY-246 BOARD (SIDE A)

PPP: PITCH sensor sensitivity

PPP

YYY

YYY: YAW sensor sensitivity

SE401

SY-246 BOARD (SIDE A)

PPP: PITCH sensor sensitivity

PPP

YYY

YYY: YAW sensor sensitivity

The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)

Note 1:When replacing the SY-246 board, erase the data in internal memory of the board before replacement.
Note 2:When replacing the SY-246 board, execute formatting and initialize the internal memory after replacement.

Copies all images in the internal memory to a memory card.

1 Insert a memory card with sufficient free capacity 

into the camera.

2

t  

(Settings) 

t 

 (Memory Card 

Tool) 

t [Copy] t [OK]

• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little 

remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.

• You cannot copy images individually.
• The original images in the internal memory are retained even after copying. To delete the contents of the 

internal memory, remove the memory card after copying, then format the internal memory ([Format] in 
[Internal Memory Tool]).

• A new folder is created on the memory card and all the data will be copied to it. You cannot choose a 

specific folder and copy images to it.

Copies all images in the internal memory to a memory card.

1 Insert a memory card with sufficient free capacity 

into the camera.

2

t  

(Settings) 

t 

 (Memory Card 

Tool) 

t [Copy] t [OK]

• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little 

remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.

• You cannot copy images individually.
• The original images in the internal memory are retained even after copying. To delete the contents of the 

internal memory, remove the memory card after copying, then format the internal memory ([Format] in 
[Internal Memory Tool]).

• A new folder is created on the memory card and all the data will be copied to it. You cannot choose a 

specific folder and copy images to it.

Formats the memory card or the internal memory. To ensure stable operations of the memory 
card, we recommend that you use this camera to format any memory card being used with this 
camera for the first time. Note that formatting will erase all data recorded on the memory card. 
This data cannot be restored. Be sure to back-up any important data to a PC or other storage 
location.

1

t  

(Settings) 

t 

 (Memory Card 

Tool) or 

 (Internal Memory Tool) 

t [Format] 

t [OK] 

• Note that formatting permanently erases all data including even protected images.

Formats the memory card or the internal memory. To ensure stable operations of the memory 
card, we recommend that you use this camera to format any memory card being used with this 
camera for the first time. Note that formatting will erase all data recorded on the memory card. 
This data cannot be restored. Be sure to back-up any important data to a PC or other storage 
location.

1

t  

(Settings) 

t 

 (Memory Card 

Tool) or 

 (Internal Memory Tool) 

t [Format] 

t [OK] 

• Note that formatting permanently erases all data including even protected images.

When replacing the lens, write down the PITCH/YAW data, FN 
data and wide limit data given on the data sheet of the replacement 
lens for service.
Start the Adjust Manual in the Adjust Station and execute the “Wide 
Limit adj.” and the “Angular velocity sensor sensitivity adj”.

L1/L2

FN

XX

YY

Wide Limit Data (2-byte data)

FN Data

PITCH/YAW Data

FN Data

PITCH data YAW data

XX YY

XX

P.PP/Y.YY

Note: The PITCH/YAW data, FN data and wide limit data of lens are 

written only repair parts.