DOWNLOAD Sony DSC-TX20 (serv.man2) Service Manual ↓ Size: 5.58 MB | Pages: 36 in PDF or view online for FREE

DSC-TX20_L2

1-2

The positions of water-proof treatment are as shown below;

BTL Packing

Packing Cabinet

TP Adhesive Sheet

Touch Panel Glass

Lens Glass

Water Sheet
Inspection

ST Window

Sheet Microphone

Conductive Connector

ML Packing

RL Packing

ZM Packing

RL Shaft

ZM Shaft

Note:
•  It may cause the water leak that assemble with attached the dust to the Packing Cabinet.
  Assemble after confirm that there is no dust on the Packing Cabinet.
•  It may cause the water leak that the adhesive paper is not attached certainly.
  Confirm that the there is no crinkle when attaching, there is no dust on the Packing Cabinet and perform the clamping certainly.

This repair flow is an example and is not compulsory.
Modify this flow as needed according to the repair standard 
and other necessary documents for each area.

To maintain the waterproof performance of this unit, annual 
replacement (charged) of the waterproof packing is recom-
mended in the user’s manual and other documents.

START

Within one year

from purchase?

No

Was a problem 

on immersion 

indicated?

No

Yes

No

OK

Is there any 

trance of immersion 

on the unit?

Yes

No

No

OK

Is there any 

trance of immersion 

on the unit?

Judge by Air-leak test

Judge by Air-leak test

Judge by Air-leak test

Normal repair start

Normal repair end

A

Yes

NG

Yes

A

(See page 1-3)

(See page 1-3)

Check waterproof 

parts.

Yes

Replace waterproof

parts.

NG

Check waterproof 

parts.

Ask the customer 

about whether to replace 

waterproof parts.

(Note 1)

END

Normal repair start

Normal repair end

NG

OK

(Note 1) 

Explain the necessity of replacing waterproof parts to the customer.
When approval is gained from the customer, replace waterproof parts.

DSC-TX20_L2

1-3

There are two types of the air-leak tester, hand pump type and compressor type. Use either between two types.

VACUUM PAD
J-6082-734-2

HAND VACUUM PUMP
J-6082-734-1

Vacuum pad and hand vacuum pump are parts for
repair, and they are included in air-leak tester.

AIR-LEAK TESTER (COMPRESSOR TYPE)
J-6082-733-A

AIR-LEAK TESTER (HAND PUMP TYPE)
J-6082-734-A

A

Check the unit status.

   Is the unit deformed?

   Is any foreign object present in the water-stopping area?

   Is the waterproof packing deformed?

   Is any scratch or crack present on exterior parts?

   Is there any trance of immersion?

No

OK

Yes

(See page 1-2)

Yes

Clean the waterproof packing.

Unrepairable

Remove foreign object from the 

water-stopping area, replace exterior 

parts/waterproof parts, etc.

When the unit cannot be repaired, 

take individual measures.

(Conforming to warranty provisions/area 

judgment)

(Note 2) 

Judge whether the unit is repairable or not based on the repair standard 

at each depot.

Repairable?

(Note 2)

No

Normal repair

Judge by Air-leak test

NG

Check waterproof 

parts.

END

Yes

Replace waterproof parts.

Ask the customer 

about whether to replace 

waterproof parts.

(Note 1)

No

(Note 1) 

Explain the necessity of replacing waterproof parts to the customer.
When approval is gained from the customer, replace waterproof parts.

DSC-TX20_L2

1-4

2.  Remove the side-mounted screw, set the two dry-cell batteries (type 9V).
 

DC power supply can be use in place of the dry-cell batteries. (DC12 V to 24 V)

 

 

• Perform the setting (Focus mode, -40.0 kPa)
1.  Press the MODE button for 3 seconds or more.
2.  Press the MODE button at 1 time.
3. Press 

the   button, and select the Foc mode.

4.  Press the MODE button at 1 time.
5. Press 

the   button, and change to “-40.0”.

6.  Press the MODE button at 6 times.
7.  Indicated value is changed to “FFF”.

• Initialize
Press the set button 5 times with holding down the MODE button.

Turn to the Right : Decrease in pressure
Turn to the Left   : Increase in pressure

Pressure Regulator Knob

Open

Close

Air Switch

1.  Insert the tube with vacuum pad into the right side connector, and connect the compressor (0.40 MPa or more) to the left side connector.

 

to Compressor

Tube (Outside diameter 6mm)

2.  Remove the side-mounted screw, set the two dry-cell batteries (type 9V).
 

DC power supply can be use in place of the dry-cell batteries. (DC12 V to 24 V)

 

1.   Insert the tube with vacuum pad into the right side connector, and connect the hand pump to the left side connector.

 

DSC-TX20_L2

1-5

 

120 sec

30 sec

60 sec

-40.0 kPa

0 kPa

-45.0 kPa

-50.0 kPa

-0.0 kPa

FFF

-5.0 kPa

-10.0 kPa

Measurement

Measure this changed value.
One minute later, it is OK
if the value within 0.45 kPa.

1.  Turn on the air-leak tester.
2.  Keep the vacuum pad by pressing it to the center of test hole on the camera.

 

OK

Tilt

NG

Test hole

Air leak

Keep vacuum pad vertically by touching with finger. 

Do not keep pressing it to the camera.
Do not touch the tube during the measurement, or measurement

value may be changed.
Perform the measurement under no vibration.

It may cause the air-leak under the condition with vibration.

3.  Press the hand pump slightly so that the indicated pressure value becomes to “-5.0”.
 

Few seconds later, decrease the pressure slightly. Therefore adjust the indicated pressure by pressing the hand pump.

Note: Perform the pressure adjustment by hand pump pushing amount.
   

If the pressure becomes too high, perform the adjustment again after removing the vacuum pad.

 

4   The change value is getting settle, wait 120 seconds with keeping the pressure at around the -5.0kPa (within -0.0kPa to -10.0kPa).

Caution:  Do not operate the hand pump after settling the change value.
   

If operate the hand pump again, wait 120 seconds form then.

1.   Turn on the air-leak tester.
2.   Hold the vacuum pad on flat surface, set the air switch to “open”, and adjust the pressure to around -5.0 by turning the pressure adjustment 

knob.

 

Inspection pressure:-45.0 ±3.0 kPa

 

3.   Confirm that there is no dust on the vacuum pad and test hole, and hold the vacuum pad by pressing it vertically to the center of test hole on the 

camera.

 

OK

Tilt

NG

Test hole

Air leak

Keep vacuum pad vertically by touching with finger. 

Do not keep pressing it to the camera.
Do not touch the tube during the measurement, or measurement

value may be changed.
Perform the measurement under no vibration.

It may cause the air-leak under the condition with vibration.

4.   Wait 120 seconds with keeping the pressure at near -5.0 kPa.
5.   Wait 10 seconds with setting air switch to “close”, and write the indicated value.
6.  In addition, leave for 1 minute, and check the pressure changes value is satisfied the following value by comparing between the written indicated 

value and indicated value.

 

Specification value  0.45 kPa or less: OK

 

 

0.46 kPa or more: NG

Caution: Do not open the connector cover and the battery/memory card cover for two minutes after the leak test.

Note: If the measurement result does not meet the specification value, check the compressor setting value and retry inspection.