DOWNLOAD Sony DSC-TX20 (serv.man2) Service Manual ↓ Size: 5.58 MB | Pages: 36 in PDF or view online for FREE

DSC-TX20_L2

1-10

When replacing the lens, write down the PITCH/YAW data, FN 
data and wide limit data given on the data sheet of the replacement 
lens for service.
Start the Adjust Manual in the Adjust Station and execute the “Wide 
Limit adj.” and the “Angular velocity sensor sensitivity adj”.

L1/L2

FN

XX YY

Wide Limit Data (2-byte data)

FN Data

PITCH/YAW Data

FN Data

PITCH data YAW data

XX YY

XX

P.PP/Y.YY

Note: The PITCH/YAW data, FN data and wide limit data of lens are 

written only repair parts.

6)  Click the [File Update] button in the window.
 

7)  A file selection screen opens. Select the Destination Data file to be added and click the [Open] button.
 

8)  When the file has been successfully added, the following window opens.
 

9)  Check the Destination Ver. window and confirm that the version has been updated.

Destination Ver. window

DSC-TX20_L2

1-11

The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)

Note 1:  When replacing the SY-333 board, erase the data in internal memory of the board before replacement.
Note 2:  When replacing the SY-333 board, execute formatting and initialize the internal memory after replacement.

Copies all images in the internal memory to a memory card. 

1. Insert a memory card with sufficient free capacity into the camera. 

2. MENU 

 

 (Settings) 

 

 (Memory Card Tool) 

 [Copy] 

 [OK]

Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little 

remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the 

data. 

Images cannot be copied individually. 

The original images in the internal memory are retained even after copying. To delete the 

contents of the internal memory, remove the memory card after copying, then format the internal 

memory ([Format] in [Internal Memory Tool]). 

The data will be copied to the recording folder that is currently being used, with a number one 

higher than the largest data number in that folder. 

Formats the memory card or the internal memory.  

When you use a memory card with this camera for the first time, it is recommended to format the card 

using the camera for stable performance of the memory card before shooting. Note that formatting 

permanently erases all data on the memory card, and is unrecoverable. Save precious data on a 

computer, etc. 

1. MENU 

 

 (Settings) 

 

 (Memory Card Tool) or 

 (Internal Memory Tool) 

 

[Format]  

[OK]

Note that formatting permanently erases all data including even protected images. 

Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.
To change settings is enabled with using the writing enabler tool (Write Enable Tool) on the Adjust Manual is activating from the Adjust Station.

1)  Start the Adjust Manual from the Adjust Station.

2) Click 

 (Write Enable Tool) button.

3)  Click “Activate Write Enable Mode” button.

4)  Upon completion of the setting change, the following message will be displayed.

5)  Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).
6)  Write the data read out into the PC to the internal memory of the camera.
7)  Disconnect the PC from the camera, and turn off the camera.

Note: By turning off the camera, the write enable setting is reset.

DSC-TX20_L2

1-12

When problems occur while the unit is operating, the self-diagnosis func-
tion starts working, and displays on the LCD screen what to do.
Details of the self-diagnosis functions are provided in the Instruction 
manual.

When problems occur while the unit is operating, the LCD screen shows 
a 4-digit display consisting of an alphabet and numbers, which blinks at 
3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in 
which the problem occurred, and “detailed code” of the problem.

0 0

3 2

C

Repaired by:

Refer to “1-12-3. Self-diagnosis Code Table”.

Indicates the appropriate

step to be taken.

E.g.
13 ....Format the “memory card”.
32 ....Turn on power again.

Block

Detailed Code

Blinks at 3.2 Hz

C : Corrected by customer

E : Corrected by service

engineer

LCD screen

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

C

1

3

0

1

The internal memory has experienced a me-
dia error.

Turn the power off and on again.

The internal memory has experienced a for-
mat error.

Format the internal memory.

Memory card is unformatted.

Format the memory card.

Memory card is broken.

Insert a new memory card.

Memory card type error.

Insert a supported memory card.

The camera cannot read or write data on the 
memory card.

Turn the power off and on again, or taking out and inserting the memory 
card several times.

C

3

2

0

1

Trouble with hardware.

Turn the power off and on again.

E

4

1

 0 

0* Abnormality of network control.

Turn power off and turn power on again.

E

4

1

 0 

1* Abnormality of network control device.

Turn power off and turn power on again.

E

6

1

0

0

Difficult to adjust focus.
(Cannot initialize focus)

Retry turn the power on by the power switch. If it does not recover, 
check the focus reset sensor of lens block (pin wa of CN401 on the 
SY-333 board). If it is OK, check the focus motor drive IC (IC401 on 
the SY-333 board).

E

6

1

1

0

Zoom operations fault.
(Cannot initialize zoom lens.)

Retry turn the power on by the power switch. Check the zoom reset 
sensor of lens block (pin ek of CN401 on the SY-333 board) when 
zooming is performed when the zoom button is operated. If it is OK, 
check the zoom motor drive IC (IC401 on the SY-333 board).

E

6

1

 3 

0*

Reset position detection error on the stepper
iris initializing.

Turn power off and turn power on again.

E

6

2

0

2

Abnormality of IC for steadyshot.

Check of the IC for steadyshot (IC401 on the SY-333 board).

E

6

2

1

0

Lens initializing failure.

Check of the IC for steadyshot (IC401 on the SY-333 board).

E

6

2

1

1

Lens overheating (PITCH).

Check the HALL element (PITCH) of optical image stabilizer (pin q;, 
qa

 of CN401 on the SY-333 board). If it is OK, check PITCH angular 

velocity sensor (SE001 on the SY-333 board) peripheral circuits.

E

6

2

1

2

Lens overheating (YAW).

Check the HALL element (YAW) of optical image stabilizer (pin 7, 
qs

 of CN401 on the SY-333 board). If it is OK, check YAW angular 

velocity sensor (SE001 on the SY-333 board) peripheral circuits.

E

6

2

2

0

Abnormality of thermistor.

Check the OIS temp sensor of optical image stabilizer (pin qk of 
CN401 on the SY-333 board).

E

9

1

0

1

Abnormality when flash is being charged.

Checking of flash unit or replacement of flash unit. (Note 1)

E

9

4

0

0

Internal memory fault.

Inspect the internal memory (IC211 on the SY-333 board).

E

9

5

 0 

0* GPS hardware error.

Turn power off and turn power on again.

E

9

5

 0 

1*

Acceleration sensor hardware error .
(GPS hardware error)

Turn power off and turn power on again.

E

9

5

 0 

2*

Electronic compass hardware error.
(GPS hardware error)

Turn power off and turn power on again.

Note 1:  After repair, be sure to perform “1-13. PROCESS AFTER FIXING FLASH ERROR”.
Note 2:  Functions of codes with * mark are not provided in this unit.

DSC-TX20_L2

1-13

When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed 
automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be on the HOME screen.

Reset Flash Error using the Flash Error Repair Tool Ver_[].[].exe

1-1.  防水/防塵・耐衝撃

1-1-1. 防水/防塵・耐衝撃性能

本機は防水/防塵性能、耐衝撃性能を備えてい
ますが、誤った使いかたによる故障は保証の対
象外になります。

•

  JIS保護等級IP58相当の防水/防塵性能があります。水

深5 m/60分までの撮影が可能です。

•

  高い水圧がかかることがあるため、水道などからの勢い

のある水を、直接あてないでください。

•

   温泉で使用しないでください。

•

   推奨動作温度−10℃から+40℃の水温でご使用くださ

い。

•

  MIL-STD  810F  Method  516.5-Shock  に準拠した

厚さ5  cmの合板上での1.5  ｍからの落下テストをクリ
アしています。*

* すべての状態において、無破損・無故障・防水性能を保

証するものではありません。

•

   防塵・耐衝撃性能については、傷やへこみがつかないこ

とを保証するものではありません。

•

  落下などの強い衝撃を与えた場合は、防水性能を保証し

ません。修理相談窓口での点検をおすすめします（有料）。

•

  付属品は防水/防塵・耐衝撃仕様ではありません。

水中・水辺で使用する前のご注意

•

  砂、髪の毛、ほこりなどの異物を、バッテリー /メモリー

カードカバー、端子カバーに挟み込まないようにしてく
ださい。わずかな異物でも浸水の原因となります。

•

  防水パッキン、防水パッキンの当たる面に傷がついてい

ないことを確認してください。わずかな傷でも浸水の原
因になります。傷がついてしまった場合は、修理相談窓
口にご相談いただき、防水パッキンを交換してください

（有料)。

 

㒐᳓ࡄ࠶ࠠࡦ

  

㒐᳓ࡄ࠶ࠠࡦߩᒰߚࠆ㕙

•

  防水パッキン、防水パッキンの当たる面にゴミや砂がつ

いているときは、繊維の残らない柔らかい布等で拭き
取ってください。バッテリー充電時やケーブル使用時
に、防水パッキンに触れて傷をつけないようにしてくだ
さい。

•

  水辺での使用中や、手に水や砂がついているときは、絶

対にバッテリー /メモリーカードカバー、 端子カバーの
開け閉めをしないでください。水や砂が本機の中に入っ
て故障の原因となります。カバーを開ける前に必ず、

「水

中・水辺で使用した後のお手入れ」を行ってください。

•

  完全に乾いた状態でカバーを開けてください。

•

   必ずバッテリー /メモリーカードカバー、端子カバーが

確実にロックされていることを確認してください。