DOWNLOAD Sony DSC-TX10 (serv.man2) Service Manual ↓ Size: 3.47 MB | Pages: 32 in PDF or view online for FREE

DSC-TX10_L2

1-2

The positions of water-proof treatment are as shown below;

Conductive Connector

Sheet Microphone

Water Sheet Inspection

Lens Glass

ST Window

Shutter button

Zoom Lever

Movie Lever

Playback Lever

Power button

Packing Cabinet

Note:
•  It may cause the water leak that assemble with attached the dust to 

the Packing Cabinet.

  Assemble after confirm that there is no dust onthe Packing Cabi-

net.

•  It may cause the water leak that the adhesive paper is not attached 

certainly.

  Confirm that the there is no crinkle when attaching, there is no dust 

on the Packing Cabinet and perform the clamping certainly.

Touch Panel Glass

TP Adhesive Sheet

ML Packing

BTL Packing

DSC-TX10_L2

1-3

Confirm the repair record and

the duration of use (With

guarantee card, etc)

NG

OK

Judge by Air-leak test

START

END

Does customer point out the waterproof problem?

Check inside for the evidence of water exposure.

Check the parts related to waterproof.

Waterproof packing, Assembling.

Nomal repair, and Waterproof

parts replacement

Before

disassembly

Clean the BT lid and ML lid.

(Check the door parts for

damages and deformation)

Replace the all exterior parts

(except Lens cover) and packings

in addition to the repair of failure

parts.

Below waterproof parts replacement is

required in addition to the repair of failure

parts.

1. In case the duration of use is less

than 1 year.

Replace the BT lid and ML lid packing.

2. In case the duration of use is more

than 1 year.

Replace the all exterior parts (except

Lens cover) and packings.

Below waterproof parts replacement is

required in addition to the repair of failure

parts.

1. In case the duration of use is less

than 1 year.

No packing replacement.

2. In case the duration of use is more

than 1 year.

Replace the BT lid and ML lid packing.

No Foreign object

Scratch/Deformation

No

Scratch/Deformation

Foreign object

NG

OK

After

assembly

NG

OK

Judge by Air-leak test

Judge by Air-leak test

Check the BT lid

and ML lid for

foreign object

Visually check the BT lid

and ML lid packing for scratch

and deformation

Estimate, and

Confirm customer's demand to

replace the waterproof parts.

There are two types of the air-leak tester, hand pump type and compressor type. Use either between two types.

VACUUM PAD
J-6082-734-2

HAND VACUUM PUMP
J-6082-734-1

Vacuum pad and hand vacuum pump are parts for
repair, and they are included in air-leak tester.

AIR-LEAK TESTER (COMPRESSOR TYPE)
J-6082-733-A

AIR-LEAK TESTER (HAND PUMP TYPE)
J-6082-734-A

DSC-TX10_L2

1-4

2.  Remove the side-mounted screw, set the two dry-cell batteries (type 9V).
 

DC power supply can be use in place of the dry-cell batteries. (DC12 V to 24 V)

 

 

• Perform the setting (Focus mode, -40.0 kPa)
1.  Press the MODE button for 3 seconds or more.
2.  Press the MODE button at 1 time.
3. Press 

the   button, and select the Foc mode.

4.  Press the MODE button at 1 time.
5.  Press the 

 button, and change to “-40.0”.

6.  Press the MODE button at 6 times.
7.  Indicated value is changed to “FFF”.

• Initialize
Press the set button 5 times with holding down the MODE button.

Turn to the Right : Decrease in pressure
Turn to the Left : Increase in pressure

Pressure Regulator Knob

Open

Close

Air Switch

1.  Insert the tube with vacuum pad into the right side connector, and connect the compressor (0.40 MPa or more) to the left side connector.

 

to Compressor

Tube (Outside diameter 6mm)

2.  Remove the side-mounted screw, set the two dry-cell batteries (type 9V).
 

DC power supply can be use in place of the dry-cell batteries. (DC12 V to 24 V)

 

1.   Insert the tube with vacuum pad into the right side connector, and connect the hand pump to the left side connector.

 

DSC-TX10_L2

1-5

 

120 sec

30

sec

60 sec

-40.0 kPa

0 kPa

-45.0 kPa

-50.0 kPa

-0.0 kPa

FFF

-5.0 kPa

-10.0 kPa

Measurement

Measure this changed value.
One minute later, it is OK
if the value within 0.45 kPa.

1.  Turn on the air-leak tester.
2.  Keep the vacuum pad by pressing it to the center of test hole on the camera.

 

Test hole

Tilt
NG

Air leak

OK

Keep vacuum pad vertically by touching with finger.
Do not keep pressing it to the camera.

Do not touch the tube during the measurement, or measurement
value may be changed.

Perform the measurement under no vibration.
It may cause the air-leak under the condition with vibration.

3.  Press the hand pump slightly so that the indicated pressure value becomes to “-5.0”.
 

Few seconds later, decrease the pressure slightly. Therefore adjust the indicated pressure by pressing the hand pump.

Note: Perform the pressure adjustment by hand pump pushing amount.
   

If the pressure becomes too high, perform the adjustment again after removing the vacuum pad.

 

4   The change value is getting settle, wait 

120

 seconds with keeping the pressure at around the -5.0kPa (within -0.0kPa to -10.0kPa).

Caution:  Do not operate the hand pump after settling the change value.
   

If operate the hand pump again, wait 

120

 seconds form then.

1.   Turn on the air-leak tester.
2.   Hold the vacuum pad on flat surface, set the air switch to “open”, and adjust the pressure to around -5.0 by turning the pressure adjustment

 

knob.

 

Inspection pressure:-45.0 ±3.0 kPa

 

3.   Confirm that there is no dust on the vacuum pad and test hole, and hold the vacuum pad by pressing it vertically to the center of test hole

 on the 

camera.

 

Test hole

Tilt
NG

Air leak

OK

Keep vacuum pad vertically by touching with finger.
Do not keep pressing it to the camera.

Do not touch the tube during the measurement, or measurement
value may be changed.

Perform the measurement under no vibration.
It may cause the air-leak under the condition with vibration.

4.   Wait 

120

 seconds with keeping the pressure at near -5.0 kPa.

5.   Wait 10 seconds with setting air switch to “close”, and write the indicated value.
6.  In addition, leave for 1 minute, and check the pressure changes value is satisfied the following value by comparing between the written indicated 

value and indicated value.

 

Specification value  0.45 kPa or less: OK

 

 

0.46 kPa or more: NG

Caution: Do not open the connector cover and the battery/memory card cover for two minutes after the leak test.

Note: If the measurement result does not meet the specification value, check the compressor setting value and retry inspection.

The changed portions from
Ver. 1.0 are shown in blue.