Sony DSC-TF1 (serv.man2) Service Manual ▷ View online
DSC-TF1_ADJ
5-5
5-2-2. White Balance Adjustment
The White Balance Adjustment is as follows.
Small pattern box (PTB-1450) setting:
Color temperature = 3150 ± 50K
Luminance: LV12.3 ± 0.2
Color temperature = 3150 ± 50K
Luminance: LV12.3 ± 0.2
The adjustment finished normally.
O WB OK
O LensShading OK
OISgainDefault X 26 Y 24
O LensShading OK
OISgainDefault X 26 Y 24
The adjustment is complete
Fig. 5-2-19
The adjustment is finished abnormally.
X Cap WB NG
O LensShading OK
OISgainDefault X 26 Y 24
OISgainDefault X 26 Y 24
Malfunction of Capture WB
adjustment
adjustment
Fig. 5-2-20
X Pre WB NG
O LensShading OK
OISgainDefault X 26 Y 24
OISgainDefault X 26 Y 24
Malfunction of Preview WB
adjustment
adjustment
Fig. 5-2-21
X WB NG
O LensShading OK
OISgainDefault X 26 Y 24
OISgainDefault X 26 Y 24
Malfunction of all
adjustment
adjustment
Fig. 5-2-22
Adjustment order
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-2-18)
Press the control button “ z (Key OK)”, then White Balance Adjustment starts.
the adjustment completion indication appears
on the screen. (Fig. 5-2-19)
on the screen. (Fig. 5-2-19)
In case of the adjustment is finished normally,
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
(Fig. 5-2-20 to 5-2-22)
(Fig. 5-2-20 to 5-2-22)
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
and readjust.
and readjust.
Screen display
Equipment required: Small pattern box (PTB-1450)
Small pattern box
(PTB-1450)
(PTB-1450)
0.5 to 1.0 cm
Black cloth
Camera
Clear chart
Fig. 5-2-18
5-2-3. Zoom Adjustment
The Zoom Over Run/Focus Back Lash Adjustment order is as follows.
Perform the Zoom adjustment in the condition the camera stands up in the horizontal plane.
Adjusting in other conditions causes a malfunction of the zoom adjustment.
Perform the Zoom adjustment in the condition the camera stands up in the horizontal plane.
Adjusting in other conditions causes a malfunction of the zoom adjustment.
The adjustment finished normally.
O Zoom Station Passed
The adjustment is complete
Fig. 5-2-23
The adjustment is finished abnormally.
X Focus backlash NG
X Zoom Adjust NG
X Zoom Adjust NG
Malfunction of zoom
adjustment result
adjustment result
Fig. 5-2-24
X Focus backlash NG
Malfunction of zoom
adjustment focus section
adjustment focus section
Fig. 5-2-25
X Zoom Adjust NG
Malfunction of zoom
adjustment zoom section
adjustment zoom section
Fig. 5-2-26
Adjustment order
Screen display
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in the horizontal plane.
Press the control button “ V (Key Down)”, then Zoom Adjustment starts.
on the screen. (Fig. 5-2-23)
In case of the adjustment is finished normally,
the adjustment completion indication appears
the adjustment completion indication appears
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
In case of the adjustment is finished abnormally,
(Fig. 5-2-24 to 5-2-26)
In this case, confirm the adjusting environment
and readjust.
In this case, confirm the adjusting environment
and readjust.
DSC-TF1_ADJ
5-6
5-2-4. Far Focus Adjustment
Note:
When using the Flange back adjustment jig, take care of the following points:
• For the illumination, use a light source such as an incandescent lamp or inverter type fluorescent light free from flickering.
• Do not make an adjustment in the environment where fluorescent lamp flickering occurs even if the illuminance can be ensured with the room
• For the illumination, use a light source such as an incandescent lamp or inverter type fluorescent light free from flickering.
• Do not make an adjustment in the environment where fluorescent lamp flickering occurs even if the illuminance can be ensured with the room
illumination only.
Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination.
Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination.
1) Install the Flange back adjustment jig so that the distance between
it and the front of lens of camera is 3 cm or less.
Note:
Note:
Take care not to hit the Flange back adjustment jig when extend-
ing the lens.
2) Make the height of Flange back adjustment jig and the camera equal.
3) Check that the center of chart meets the center of shot image screen
with the zoom lens at TELE end and WIDE end respectively.
Color temperature = 5000 ± 300K
Be sure not to turn off the power during adjusting.
The adjustment finished normally.
O Far Focus Station Passed
Please Key MENU Enter...
The adjustment is complete
Fig. 5-2-28
The adjustment is finished abnormally.
X Far Focus NG !
Malfunction of Far Focus
Fig. 5-2-29
Adjustment order
Screen display
3 cm or less
Equipment required: Flange back adjustment jig
Flange back adjustment jig
Camera
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Flange back adjustment jig. (Fig. 5-2-27)
Press the control button “ b (Key Left)”, then Far Focus Adjustment starts.
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-2-28)
Turn off the power to quit the adjustment mode.
the adjustment completion indication appears
on the screen. (Fig. 5-2-28)
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
In case of the adjustment is finished abnormally,
(Fig. 5-2-29)
In this case, confirm the adjusting environment
and readjust.
In this case, confirm the adjusting environment
and readjust.
Fig. 5-2-27
5-2-5. Near Focus Adjustment
Note:
Perform the Near Focus Adjustment after the Far Focus Adjustment.
1) Be sure to set 50 ± 1 cm distance between the chart and the tip of camera lens.
2) Check that the center of chart meets the center of shot image screen with the zoom
lens at TELE end and WIDE end respectively.
Color temperature = 5000 ± 300K
Be sure not to turn off the power during adjusting.
The adjustment finished normally.
O Near Focus Station Passed
Please Key MENU Enter...
The adjustment is complete
Fig. 5-2-31
The adjustment is finished abnormally.
ADJ Nearfocus
Zoom:XX
Big Step:XXXX
i:2 N:XXXX F:XXXX
Please Readjust
Best Focus:XXXX
Contrast:XXXX
Malfunction of Near Focus
adjustment In case of
the Near Focus adjustment
is failed, readjust the Far
Focus and try to readjust
the Near Focus.
adjustment In case of
the Near Focus adjustment
is failed, readjust the Far
Focus and try to readjust
the Near Focus.
Fig. 5-2-32
Note:
The screen above is an example.
Adjustment order
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Chart. (Fig. 5-2-30)
Press the control button “ B (Key Right)”, then Near Focus Adjustment starts.
on the screen. (Fig. 5-2-31)
In case of the adjustment is finished normally,
the adjustment completion indication appears
the adjustment completion indication appears
Turn off the power to quit the adjustment mode.
(Fig. 5-2-32)
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
the following indication appears on the screen.
In this case, confirm the adjusting environment
and readjust.
In case of the Near Focus adjustment is failed,
readjust the Far Focus adjustment and try to
readjust the Near Focus adjustment.
and readjust.
In case of the Near Focus adjustment is failed,
readjust the Far Focus adjustment and try to
readjust the Near Focus adjustment.
Screen display
Chart
Camera
Equipment required: Chart
50 ± 1 cm
Fig. 5-2-30
DSC-TF1_ADJ
5-7
5-2-6. Super Near Focus Adjustment
Note:
Perform the Super Near Focus Adjustment after the Near Focus Adjustment.
1) Be sure to set 10 ± 1 cm distance between the chart and the tip of camera lens.
2) Check that the center of chart meets the center of shot image screen with the zoom
lens at TELE end and WIDE end respectively.
Color temperature = 5000 ± 300K
Be sure not to turn off the power during adjusting.
The adjustment finished normally.
O SuperNear Focus Station Passed
Please Key MENU Enter...
The adjustment is complete
Fig. 5-2-34
The adjustment is finished abnormally.
X SuperNear Focus NG !
Malfunction of Super Near
Focus adjustment.
In case of the Super Near
Focus adjustment is failed,
readjust from the Far Focus
and try to readjust the
Super Near Focus.
Focus adjustment.
In case of the Super Near
Focus adjustment is failed,
readjust from the Far Focus
and try to readjust the
Super Near Focus.
Fig. 5-2-35
Adjustment order
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Chart. (Fig. 5-2-33)
Press the control button “ (Key Del)”, then Near Focus Adjustment starts.
on the screen. (Fig. 5-2-34)
In case of the adjustment is finished normally,
the adjustment completion indication appears
the adjustment completion indication appears
Turn off the power to quit the adjustment mode.
(Fig. 5-2-35)
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
the following indication appears on the screen.
In this case, confirm the adjusting environment
and readjust.
In case of the Super Near Focus adjustment is
failed, readjust from the Far Focus adjustment and
try to readjust the Super Near Focus adjustment.
and readjust.
In case of the Super Near Focus adjustment is
failed, readjust from the Far Focus adjustment and
try to readjust the Super Near Focus adjustment.
Screen display
Chart
Camera
Equipment required: Chart
10 ± 1 cm
Fig. 5-2-33
5-2-7. Set Language Destination
Language Destination Setting:
Save “lang.txt” in the root directory of the microSD or
Save “lang.txt” in the root directory of the microSD or
Memory Stick Micro
being used.
The content of “lang.txt” is as follows:
Language Destination (for example: E37)
Product ID (10 characters) (refer to “5-3 PRODUCT ID LIST”)
Serial Number (7 characters)
Product ID (10 characters) (refer to “5-3 PRODUCT ID LIST”)
Serial Number (7 characters)
The following is an example of U2 Language Destination Setting for DSC-TF1 black camera.
U2
0080812934
0120243
0080812934
0120243
Especially Attention:
1) The enter key must be the end symbol of each row.
2) For the Product ID, refer to “5-3 PRODUCT ID LIST”.
3) The Serial Number must be 7 characters. It refer to the serial number of shipment.
1) The enter key must be the end symbol of each row.
2) For the Product ID, refer to “5-3 PRODUCT ID LIST”.
3) The Serial Number must be 7 characters. It refer to the serial number of shipment.
The adjustment is finished abnormally.
Read Language NG!
Malfunction of Set Language
Destination.
In case of the Set Language
Destination is failed, reset
the Language Destination.
Destination.
In case of the Set Language
Destination is failed, reset
the Language Destination.
Fig. 5-2-37
Setting order
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Press the Shutter button (Key S1), then Language Destination Setting starts.
this setting completion indication appears
on the screen. (Fig. 5-2-36)
on the screen. (Fig. 5-2-36)
In case of this setting is finished normally,
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
(Fig. 5-2-37)
(Fig. 5-2-37)
and retry settting.
In case of this setting is finished abnormally,
In this case, confirm the setting environment
Screen display
The setting finished normally.
Set LangDestination OK!
The setting is complete
Fig. 5-2-36
Note:
The screen above is an example.
Note:
The screen above is an example.
Set Lang Destination
NOT CORRECT Destination!!!
Malfunction of Set Language
Destination.
Check the content of
Destination.
Check the content of
“
lang.txt
”
, then execute the
Set Language Destination.
Fig. 5-2-38
DSC-TF1_ADJ
5-8E
Selectable language table
SELECTABLE LANGUAGE
VIDEO OUT
Default
DESTINA
TION
AREA
Japanese
English
French
German
Spanish
Italian
Portuguese
Brazilian Portuguese
Simplified Chinese
T
raditional Chinese
Arabic
Dutch
Russian
Swedish
Korean
Norwegian
Danish
Finnish
Polish
Hungarian
Czech
Persian
Thai
Greek
T
urkish
Malay
Croatian
Romanian
Indonesian
Bulgarian
V
ietnamese
Ukrainian
U2
US
z
a
a
a
NTSC
CA2
Canadian
z
a
a
a
a
NTSC
CE3
AEP
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
CEH
UK
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
RU3
Russian
a
a
a
a
a
a
a
z
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
E32
E
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
E33
E
a
a
z
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
AU2
Australian
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
HK1
Hong Kong
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
BR4
Brazilian
a
a
a
a
z
a
a
a
a
a
a
a
a
a
a
NTSC
J1
Japanese
z
NTSC
z
: INITIAL LANGUAGE
5-3. PRODUCT ID LIST
Area
Color
Product ID
U2
Black
0080812934
Blue
0080812936
Red
0080812935
CA2
Black
0080812940
Blue
0080812942
Red
0080812941
CE3
Black
0080812950
Blue
0080812993
Red
0080812963
CEH
Black
0080812960
Blue
0080812962
Red
0080812961
RU3
Black
0080812952
E32
Black
0080812910
Blue
0080812986
Red
0080812970
Area
Color
Product ID
E33
Black
0080812911
Blue
0080812987
Red
0080812971
AU2
Black
0080812990
Blue
0080812992
Red
0080812991
HK1
Black
0080812913
BR4
Black
0080812954
Blue
0080812997
Red
0080812967
J1
Black
0080812900
Blue
0080812902
Red
0080812901
Display
