Sony DSC-T7 (serv.man2) Service Manual ▷ View online
1-1
DSC-T7
1. SERVICE NOTE
• NOTE FOR REPAIR
[Discharging of the FLASH unit’s charging capacitor]
The charging capacitor of the FLASH unit is charged up to the
maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the DSC-T7 is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the DSC-T7 is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig. a small clip is attached to each end of a
resistor of 1 k
resistor of 1 k
Ω
/1 W (1-215-869-11)
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
When remove a connector, don't pull at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
Discharging the Capacitor
1
Remove the cabinet (front) assembly.
2
Peel off the absorbing sheet.
3
Remove the flexible board.
4
Short circuits between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
Capacitor
Shorting jig
(1k
(1k
Ω
/ 1w)
Flash unit
1-2E
DSC-T7
Note :
The error code is cleared if the battery is removed, except defective flash unit.
*1: The error display is given in two ways.
*1: The error display is given in two ways.
Display Code
C:32:01
C:13:01
E:91:01
E:01:XX
E:61:00 *1
E:61:10 *1
Countermeasure
Turn off the main power then back on.
Replace the memory stick.
Format the memory stick with the DSC-T7.
Format the memory stick with the DSC-T7.
Checking of flash unit or replacement of
flash unit.
flash unit.
Checking of lens drive circuit
Cause
Trouble with hardware.
• The type of memory stick that cannot be
used by this machine, is inserted.
• Data is damaged.
• Unformatted memory stick is inserted.
• Unformatted memory stick is inserted.
Abnormality when flash is being
charged.
charged.
When failed in the focus initialization.
Caution Display During Error
SYSTEM ERROR
MS ERROR
Flash LED
Flash display
Flashing at 3.2 Hz
Flash display
Flashing at 3.2 Hz
—
Self-diagnosis display
• C: ss: ss
The contents which can be handled
by customer, are displayed.
by customer, are displayed.
• E: ss: ss
The contents which can be handled
by engineer, are displayed.
by engineer, are displayed.
[Description on Self-diagnosis Display]
DSC-T7
2-1
2-2
2-1. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2. DISASSEMBLY
SY
-1
15
SY
-1
15
SY
-1
15
SY
-1
15
SY
-1
15
SY
-1
15
SY
-1
15
7
b
a
b
e
c
f
3
1
2
8
HELP 01
HELP 03
HELP 05
HELP 02
1
Two screws (M1.4x2.5) silver
2
Screw (M1.4x2.5) silver
3
Two screws (M1.4x2.5) silver
4
Twist the strap in the direction of arrow a.
5
Open the battery lid.
6
Grab b, c, and d, and apply force so that d turns
counterclockwise to disengage the claw e.
Some reassembling steps of the unit require attention.
Be sure to read HELP before reassembling.
Be sure to read HELP before reassembling.
1
Flexible board (Flash unit)
2
Pick up the AF guide
3
Two claws
4
Claw
5
Two claws
6
AF LED
7
AF guide
8
Flash unit
1
Control switch block (GP51710)
2
Screw (M1.4x2.5) silver
3
Remove the two claws in the direction
of the arrow.
4
Main frame assembly, LCD unit, etc.
5
Cabinet (rear) assembly,
control switch block (GP51710), etc.
1
SW-454 flexible board
2
Claw
3
SW-454 flexible board
4
Two claws
5
Claw
6
Flexible board
(from the Control switch block (RL51710))
7
Flexible board
(from the MS-258 board)
8
SY-115 board, MS guide assembly, etc.
Work while suppressing MC sheet metal
by the finger.
MC sheet metal
1
Claw
2
MS guide assembly
3
SY insulating sheet
4
SW-454 flexible board
5
SY-115 board, battery terminal board
1
MS-258 board
2
Two MS electrostatic sheets
1
Absorbing sheet
2
Flexible board (from the LCD unit)
7
Claw f
8
Cabinet (front) assembly
9
Ornamental plate
2
4
1
5
6
8
7
4
1
5
4
3
3
2
3
Capacitors
Shorting jig
(1k
(1k
Ω
/ 1w)
Flash unit
Be sure to discharge the capacitor.
Caution
1
2
5
6
2
1
1
UKI sheet
2
Flexible board (from the lens unit)
3
Flexible board
(from the CCD block assembly)
4
Lens section
9
1
2
1
4
5
8
6
7
2
3
2
1
3
5
4
1
Control switch block (RL51710)
2
Claw
3
MC sheet metal
4
MC-149 board
1
4
3
2
HELP 04
(disassembly of the control
switch block (GP51710))
(disassembly of the control
switch block (GP51710))
HELP 06
(disassembly of the control
switch block (RL51710))
(disassembly of the control
switch block (RL51710))
HELP 07
(disassembly of the piezo
speaker)
(disassembly of the piezo
speaker)
Note:
Be careful not to drop the
MC sheet metal.
Note:
Be careful not to deform
the Cabinet (front) assembly.
4
DSC-T7
2-3
2-4
2. DISASSEMBLY
2. DISASSEMBLY
2-2. SERVICE POSITION
SY
-115
BOARD
SY
-1
15
SY
-1
15
SY
-1
15
SY
-1
15
SY
-1
15
SY
-1
15
SY
-1
15
[SERVICE POSITION TO CHECK THE SY-115 BOARD]
Note1: By using an adhesive tape, press the lens cover switch (S701).
Note2: When checking the VIDEO AMP (SY-115 board IC350), connect an A/V connecting cable to the A/V jack of the conversion adaptor.
Note2: When checking the VIDEO AMP (SY-115 board IC350), connect an A/V connecting cable to the A/V jack of the conversion adaptor.
AC power
adaptor
adaptor
AC IN
DC-IN
SW-454
flexible board
flexible board
MC-149 board
Conversion
adaptor
adaptor
SY-115 board,
Battery terminal board
Battery terminal board
CN707
CN001
CN703
CN705
CN702
CN704
CN701
CN706
CN002
CN001
Lens section
CD-541 board
MS-258 board
Flash unit
Control switch block
(GP51710)
(GP51710)
Control switch block
(RL51710)
(RL51710)
LCD unit
S701 Lens cover
switch (Note1)
switch (Note1)
Capacitors
Shorting jig
(1k
(1k
Ω
/ 1w)
Flash unit
Be sure to discharge the capacitor.
Caution
7
3
8
1
2
1
2
2
4
3
1
5
7
6
8
4
3
2
1
5
4
3
2
4
5
8
6
7
1
2
3
5
4
2
1
1
4
3
2
9
1
2
3
a
b
c
5
6
4
1
Click on the first or last page to see other DSC-T7 (serv.man2) service manuals if exist.