Sony DSC-S730 (serv.man2) Service Manual ▷ View online
5-4
DSC-S730_ADJ
5-2-2. Aperture Diameter/Mechanical Shutter Adjustment
The Aperture Diameter/Mechanical Shutter adjustment order is as follows.
Small pattern box setting:
Color temperature = 3000
±
300K
Adjustment order
Screen display
The adjustment finished normally.
The adjustment is finished abnormally.
Fig. 5-2-4
Fig. 5-2-5
Fig. 5-2-6
Fig. 5-2-7
Fig. 5-2-8
Set the unit to the adjustment mode.
* For the setting procedure of the adjustment mode, refer to "Preparations" (Page 5-2).
Place the camera in front of the small pattern box.
Press the control button “v”, then Aperture Diameter/Mechanical Shutter Adjustment starts.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
In case of the adjustment is finished normally.
the adjustment completion indication appears
on the screen. (Fig. 5-2-4)
Turn off the power to quit the adjustment mode.
the adjustment completion indication appears
on the screen. (Fig. 5-2-4)
Turn off the power to quit the adjustment mode.
In case of the adjustment is finished abnormally.
the following indication appears on the screen.
(Fig. 5-2-5 to 5-2-8)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 5-2-5 to 5-2-8)
In this case, confirm the adjusting environment
and readjust.
DarkLumi O
OK O O O
MTrigger8 95
ExpoTime86665
OK O O O
MTrigger8 95
ExpoTime86665
MShutter Adjust...
O MSHUTTER: 95 95 96
O MSHUTTER: 95 95 96
The adjustment is complete.
X ADJUST IRIS NG
Malfunction of Aperture
Diameter adjustment
Diameter adjustment
O ADJUST IRIS OK
X MSHUTTER No Close
Malfunction of Mechanical
Shutter adjustment
Shutter adjustment
O ADJUST IRIS OK
X Mshutter Speed too big
O ADJUST IRIS OK
X Mshutter Speed too Small
Malfunction of Mechanical
Shutter adjustment
Shutter adjustment
Malfunction of Mechanical
Shutter adjustment
Shutter adjustment
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2008.09
5-5
DSC-S730_ADJ
5-2-3. Zoom Adjustment
Perform the zoom adjustment in the conditon the camera stands up.
Adjusting in the other conditon causes the malfuncton of the zoom adjustment.
Adjustment order
Screen display
The adjustment finished normally.
The adjustment is finished abnormally.
Fig. 5-2-9
Fig. 5-2-10
Fig. 5-2-11
Fig. 5-2-12
The adjustment is complete.
Malfunction of Zoom adjust-
ment result
ment result
Malfunction of Zoom adjust-
ment Focus section
ment Focus section
Malfunction of Zoom adjust-
ment Zoom section
ment Zoom section
Set the unit to the adjustment mode.
* For the setting procedure of the adjustment mode, refer to "Preparations" (Page 5-2).
Press the control button “V”, then Zoom Adjustment starts.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
In case of the adjustment is finished normally.
the adjustment completion indication appears
on the screen. (Fig. 5-2-9)
Turn off the power to quit the adjustment mode.
the adjustment completion indication appears
on the screen. (Fig. 5-2-9)
Turn off the power to quit the adjustment mode.
In case of the adjustment is finished abnormally.
the following indication appears on the screen.
(Fig. 5-2-10 to 5-2-12)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 5-2-10 to 5-2-12)
In this case, confirm the adjusting environment
and readjust.
O Zoom Station Passed
X Focus backlash NG
X Zoom Adjust NG
X Focus backlash NG
X Zoom Adjust NG
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2008.09
5-6
DSC-S730_ADJ
5-2-4. Infinity Focus Adjustment
Note:
When using the flange back adjustment jig, take care of the following points:
•
For the illumination, use a light source such as an incandescent lamp or inverter type fluorescent light free from flickering.
•
Do not make an adjustment in the environment where fluorescent lamp flickering occurs even if the illuminance can be ensured
with the room illumination only.
Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination.
with the room illumination only.
Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination.
1)
Install the flange back adjustment jig so that the distance between
it and the front of lens of camera is less than 3 cm.
it and the front of lens of camera is less than 3 cm.
Note:
Take care not to hit the flange back adjustment jig
when extending the lens.
2)
Make the height of flange back adjustment jig and the camera equal.
3)
Check that the center of chart meets the center of shot image
screen with the zoom lens at TELE end and WIDE end respectively.
screen with the zoom lens at TELE end and WIDE end respectively.
Fig. 5-2-13
Color temperature = 5000
±
300K
Be sure not to turn off the power during adjusting.
Adjustment order
Screen display
The adjustment finished normally.
The adjustment is finished abnormally.
Fig. 5-2-14
Fig. 5-2-15
Flange back adjustment jig
3 cm or less
Camera
Set the unit to the adjustment mode.
* For the setting procedure of the adjustment mode, refer to "Preparations" (Page 5-2).
Place the camera in front of the Flange back adjustment jig.
Press the control button “b”, then Infinity Focus Adjustment starts.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
In case of the adjustment is finished normally.
the adjustment completion indication appears
on the screen. (Fig. 5-2-14)
Turn off the power to quit the adjustment mode.
the adjustment completion indication appears
on the screen. (Fig. 5-2-14)
Turn off the power to quit the adjustment mode.
In case of the adjustment is finished abnormally.
the following indication appears on the screen.
(Fig. 5-2-15)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 5-2-15)
In this case, confirm the adjusting environment
and readjust.
The adjustment is complete.
Malfunction of Infinity Focus
adjustment result
adjustment result
O Far Focus Station Passed
Please Key MENU Enter...
X Far Focus NG !
Please ReAdjust Far Focus
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2008.09
5-7E
DSC-S730_ADJ
5-2-5. Near Focus Adjustment
Note:
Perform the Near Focus Adjustment after the Infinity Focus adjustment.
Equipments required:
Camera table
Chart
Chart
Fig. 5-2-16
Be sure to set 0.50
± 0.01 m distance between the chart and the tip of camera lens.
Color temperature = 5000
±
300K
Be sure not to turn off the power during adjusting.
Adjustment order
Screen display
The adjustment finished normally.
The adjustment is finished abnormally.
The adjustment is complete.
Malfunction of Near Focus
adjustment result
adjustment result
Chart
0.50
±
0.01 m
Camera
Set the unit to the adjustment mode.
* For the setting procedure of the adjustment mode, refer to "Preparations" (Page 5-2).
Set the camera as show in Fig. 5-2-16.
Press the control button “B”, then Near Focus Adjustment starts.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
In case of the adjustment is finished normally.
the adjustment completion indication appears
on the screen. (Fig. 5-2-17)
Turn off the power to quit the adjustment mode.
the adjustment completion indication appears
on the screen. (Fig. 5-2-17)
Turn off the power to quit the adjustment mode.
In case of the adjustment is finished abnormally.
the following indication appears on the screen.
(Fig. 5-2-18)
In this case, confirm the adjusting environment
and readjust.
In case of the Near Focus adjustment is faild,
readjust the Infinity Focus adjustment and try to
readjust the Near Focus adjustment.
the following indication appears on the screen.
(Fig. 5-2-18)
In this case, confirm the adjusting environment
and readjust.
In case of the Near Focus adjustment is faild,
readjust the Infinity Focus adjustment and try to
readjust the Near Focus adjustment.
O Near Focus Staton Passed
Please Key MENU Enter...
X Near Focus NG !
Please ReAdjust Far Focus
Fig. 5-2-17
Fig. 5-2-18
In case of the Near Focus
adjustment is faild, readjust the
Infinity Focus adjustment and
try to readjust the Near Focus
adjustment.
adjustment is faild, readjust the
Infinity Focus adjustment and
try to readjust the Near Focus
adjustment.
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2008.09
Click on the first or last page to see other DSC-S730 (serv.man2) service manuals if exist.