Sony DSC-S600 (serv.man2) Service Manual ▷ View online
2-1
2. DISASSEMBLY
2. DISASSEMBLY
DSC-S600_L2
2. DISASSEMBLY
NOTE FOR REPAIR
DISCHARGING OF THE FLASHLIGHT POWER SUPPLY CAPACITOR
The charging elect capacitor 180uF (330V) is charged up to the
maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the DSC-S600 is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the DSC-S600 is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig. a small clip is attached to each end of
a resistor of 1 kW /1 W (1-215-869-11)
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
a resistor of 1 kW /1 W (1-215-869-11)
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
When remove a connector, don't pull at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
Discharging the Capacitor
Short circuits between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
charged capacitor with the short jig about 10 seconds.
SY-145
Shorting jig
(1k
(1k
Ω
/ 1W)
Capacitor
DSC-S600_L2
2-3
2-4
2-1. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2. DISASSEMBLY
2. DISASSEMBLY
2. DISASSEMBLY
SY-145
SY-145
SY-145
SY-145
5
7
6
2
3
4
1
2
3
5
1
8
4
3
2
1
1
Slide the BT cover.
2
Screw (M1.7x4)
3
Open the USB cover.
4
Screw (M1.7x4)
5
Screw (M1.7x4)
6
Screw (M1.7x4)
7
Open the cabinet (upper) assembly.
8
Cabinet (rear) assembly
1
Three solderings
2
Two solderings
3
Open the BT cover.
4
Open the cabinet (upper) assembly.
5
Cabinet (front) assembly
1
Two solderings
2
Flexible board (from the LCD unit)
3
LCD unit
1
Two solderings
2
Claw
3
Two claws
4
Flexible board (from the lens block assembly)
5
Flexible board (from the lens block assembly)
6
Flexible flat cable (FFC-058)
7
Flexible flat cable (FFC-056)
8
SY-145 board, RL-063 board,
speaker, microphone, etc.
1
4
3
2
1
Screw (M1.7x4)
2
Two claws
3
RL-063 board
4
Cabinet (upper) assembly
1
2
8
3
5
6
4
A
(See page 2-5)
C
(See page 2-5)
B
(See page 2-5)
7
Refer to page 2-1 "DISCHARGING OF
THE FLASHLIGHT POWER SUPPLY
CAPACITOR (LND904, LND905)",
when discharging the capacitor.
THE FLASHLIGHT POWER SUPPLY
CAPACITOR (LND904, LND905)",
when discharging the capacitor.
HELP 02
HELP 01
HELP 03
HELP 04
DSC-S600_L2
2. DISASSEMBLY
2. DISASSEMBLY
2-5
2-6E
SY-145
SY-145
SY-145
SY-145
A
C
B
3
1
4
1
5
1
Flexible flat cable (FFC-058)
2
Flexible board (from the optical unit)
3
Screw (M1.7x4)
4
LCD frame
5
SW-461 board, flexible flat cable (FFC-058)
1
Two solderings
2
Speaker holder
3
Speaker
4
Two solderings
5
Miclophone holder
6
Miclophone
HN-015
1
Two solderings
2
Elect 180uF (330V) capacitor
3
Three solderings
4
Flash unit, harness (HN-015)
5
SY-145 board, RL-063 board,
flexible flat cable (FFC-056), etc.
4
1
2
3
1
2
4
5
2
4
1
Flexible board (from the lens block assembly)
2
Flexible board (from the lens block assembly)
3
Flexible board (from the optical unit)
4
Lens block assembly, optical unit.
3
2
HELP 05
HELP 06
3
5
6
RL-063
SW-461
DSC-S600_L2
HELP
HELP
Disassembling and assembling procedures that require attention are described here.
Mode Switch of
the SW-461 board
Cabinet (rear) assembly
HELP 01
When installing the Cabinet (Rear) assembly, install it while aligning the
Mode switch of the
Mode switch of the
SW-461 board
with the position A of the Cabinet (Rear) assembly.
A
Yellow
Two reads
(from the BM-001 board)
(from the BM-001 board)
Tree reads
(from the LB-117 board)
(from the LB-117 board)
Red
SW-461 board
Black
Gray
White
HELP 02
Solder each lead according to the color (Y: yellow, G: gray, W: white, R: red, B: black) displayed on the SW-461 board.
Click on the first or last page to see other DSC-S600 (serv.man2) service manuals if exist.