Sony DSC-RX10 (serv.man2) Service Manual ▷ View online
DSC-RX10_L2
2-3
– ENGLISH –
– JAPANESE –
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked
of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, don’t press down at wire of con-
nector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
DISCHARGING OF THE CHARGING CAPACITOR (C901, C902)
The charging capacitor is charged up to the maximum 315 V
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω/1 W
Wrap insulating tape.
1 k
Ω/1 W
Wrap insulating tape.
(Part code: 1-215-869-11)
C901
C902
R:1 k
Ω/1 W
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.
Short-circuit between two points with
the short jig about 10 seconds.
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け，
折れ等がないことを確認する。
また，コネクタへの接続は，差し込み不足や斜め差しになら
ないように注意する。
• コネクタを取り外す時に，線材部（極細）を持って引っ張ると
断線する恐れがありますので，絶対に線材部（極細）を持って
引っ張らないでください。
引っ張らないでください。
• 線材部（極細）を押さえながらコネクタを差し込むと，線材部
（極細）が断線する恐れがありますので，絶対に線材部（極細）
には負担をかけないでください。
• 金メッキされているフレキシブル基板には，強い負担をかけ
ないでください。
ストロボ用充電コンデンサ（C901, C902）の放電
ストロボ用充電コンデンサは最大315Vの電圧で充電され
ています。
この高電圧で充電されたコンデンサに手を触れた場合，
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず，残留しています。こ
のため，下記の方法で残留電圧を放電してください。
ています。
この高電圧で充電されたコンデンサに手を触れた場合，
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず，残留しています。こ
のため，下記の方法で残留電圧を放電してください。
ショート治具の準備
ショート治具は1kΩ/1W抵抗（1-215-869-11）の両端に
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
R:1 k
Ω/1 W
C901
C902
コンデンサの放電
フラッシュユニットの電源コンデンサ
の端子間をショート治具で約10秒間
接続する。
フラッシュユニットの電源コンデンサ
の端子間をショート治具で約10秒間
接続する。
DSC-RX10_L2
2-4
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
4-478-910-01
LIGHT, JK GUIDE,
2
4-478-898-01 BOTTOM,
CABINET
3
4-478-919-01
RUBBER (63720), EYE CUP
4
4-478-897-01 KNOB,
VISIBILITY
ADJUSTMENT
5
1-492-592-11
SWITCH BLOCK, CONTROL (BK77900)
6
4-527-984-01
GASKET (SW BASE)
* 7
4-478-900-01
SHEET METAL, SW BASE
8
A-1973-078-A FC-1002 FLEXIBLE BOARD, COMPLETE
9
1-492-683-11
CONTROL SWITCH BLOCK (ENSW63720)
10
4-438-734-01
SHOE CAP (875)
11
4-478-948-01
SHEET, VF RADIATION
12
X-2588-236-1 VF
UNIT
ASSY
13
4-411-332-01
TAPE (AS (C))
14
4-480-644-01 SHEET
(FC)
C901
1-118-124-11
ELECT 67uF 315V
*C902
1-116-488-11
ELECT 47.5uF 315V
LCD902 8-753-379-22 ECX333AA-1
#1
2-635-562-11 SCREW
(M1.7)
#2
2-635-562-31 SCREW
(M1.7)
#12
3-080-204-21 SCREW, TAPPING, P2
1. Remove in numerical order (
1
to
9
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇
-X: Solder
DISASSEMBLY
Screw
#1: M1.7 X 2.5
(Black)
2-635-562-11
2-635-562-11
2.5
1.7
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
(Claw)
C901
C902
1
4
5
10
13
11
12
7
6
9
14
3
2
#2
#2
LCD902
#2
#2
#12
#1
Rear Cabinet Section
(See page 2-10)
Main Board Section
(See page 2-5)
1
5
7
6
8
8
9
3
2
4
2
#2 X 8
#2
#2
Bottom View
3
#12 X 1
#12
Back View
4
#2 X 5
#2
#2
#2
Left View
Right View
Back View
5
DISCHARGING OF THE CHARGING CAPACITOR
ストロボ用充電コンデンサの放電
7
#1 X 3
#1
Back View
DSC-RX10_L2
2-5
2-1-2. MAIN BOARD SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
4-478-899-01 GRIP
(FRONT)
52
A-1973-588-A SY-1027 BOARD, COMPLETE (SERVICE) (Note 1)
* 53
4-484-165-01
SHEET, IC RADIATION
* 54
4-478-905-01 FRAME, JK
55
4-480-645-01 SPEAKER,
CUSHION
56
1-889-134-11
CN-1026 FLEXIBLE BOARD
57
4-488-783-01
FRAME, CUSHION (JK)
58
4-489-532-01 EYELET
TRIANGL
(779)
59
4-487-875-01
HOLDER, EYELET TRIANGLE (779)
60
4-488-193-01 SHEET
(VF),
ADHESIVE
61
4-532-502-01
SPACER (CABINET UPPER)
ANT901 A-1989-833-A NFC BLOCK ASSY (SERVICE) (Note 2)
BT1000 1-756-813-11
LITHIUM RECHARGEABLE BATTERY
SP901
1-826-837-91
SPEAKER (1.3CM) (Note 3)
#1
2-635-562-11 SCREW
(M1.7)
#2
2-635-562-31 SCREW
(M1.7)
#5
3-080-204-01 SCREW,
TAPPING,
P2
1. Remove in numerical order (
1
to
4
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇
: Solder
DISASSEMBLY
1
#5 X 2
#5
Bottom View
2
#5 X 1 → #1 X 1 → #2 X 1 → #1 X 1 → #1 X 5
#1
#5
#5
#2
#1
Back View
Left View
Right View
Front View
Screw
#1: M1.7 X 2.5
(Black)
2-635-562-11
2-635-562-11
2.5
1.7
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
#5: M1.7 X 3.5 (Tapping)
(Black)
3-080-204-01
3-080-204-01
3.5
1.7
A
B
B
A
(Claw)
(Claw)
(Claw)
(Claw)
57
56
53
55
58
58
59
59
60
52
51
61
54
#2
#2
BT1000
ANT901
(Note 2)
(Note 2)
SP901
(Note 3)
(Note 3)
#2
#1
#1
#1
#5
#5
#5
3
3
4
1
2
Upper Cabinet Section
(See page 2-8)
Front Cabinet Section 1
(See page 2-6)
: BT1000 (LITHIUM BATTERY)
Board on the mount position.
(See page 6-37 of Level 3)
Board on the mount position.
(See page 6-37 of Level 3)
(Note 1)
3
#2 X 3 → Open the USB lid (
3
) → #1 X 1
#2
#1
Back View
Right View
Note
Note 1: When this part is removed, adjustment is required.
For the adjustment method, refer to “Adjustment items after
replacing parts” in the Note tab of the Adjust manual.
replacing parts” in the Note tab of the Adjust manual.
Note 1: この部品を取り外したときは調整が必要です。
調 整 方 法 に つ いてはAdjust manual の Noteタブ にある
Adjustment items after replacing parts を参照してください。
Note 2: Refer to “Assembly-1: Notes on installing the NFC Block Assy”
when assembling.
Note 2: 組立時は Assembly-1: Notes on installing the NFC Block Assy
を参照してください。
Note 3: Refer to “Assembly-2: Notes on installing the Speaker” when
assembling.
Note 3: 組立時は Assembly-2: Notes on installing the Speaker を
参照してください。
4
#2 X 1
#2
Back View
DSC-RX10_L2
2-6
2-1-3. FRONT CABINET SECTION 1
ns : not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
A-1989-834-A CD-847 FLEXIBLE BOARD, COMPLETE (SERVICE)
(Note2, 3, 4)
102
4-470-413-01 RUBBER,
SEAL
103
4-478-904-01 SCREW,
TRIPOD
104
X-2588-287-1 STRAP EYELET ASSY (L)
* 105
4-478-903-01 FRAME, MAIN
106
A-1992-176-A HOLDER ASSY, SY (SERVICE)
107
Selection Parts SPACER PLATE
108
4-478-915-01
SHEET METAL, JK ELECTROSTATIC
109
4-528-669-01
SHEET (SY HOLDER)
#1
2-635-562-11 SCREW(M1.7)
#12
3-080-204-21 SCREW,
TAPPING,
P2
#155 3-080-204-31 SCREW,
TAPPING,
P2
#305
3-703-816-19
SCREW (M1.4X4.0), SPECIAL HEAD
1. Remove in numerical order (
1
to
4
) in the left figure.
DISASSEMBLY
Lens Block Section
(See page 2-11)
(Note 1, 2)
Front Cabinet Section 2
(See page 2-7)
2
1
4
3
(Note 5)
(Claw)
101
102
103
106
105
108
109
104
107
107
#12
#305
#12
#12
#155
(including CP001
(CMOS imager))
(Note 2, 3, 4)
(CMOS imager))
(Note 2, 3, 4)
#155
#1
ns
ns
ns
2
#12 X 4
4
#155 X 4
Back View
#12
#12
#12
Back View
#155
#155
#155
Screw
#1: M1.7 X 2.5
(Black)
2-635-562-11
2-635-562-11
2.5
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
1.7
6.0
#155:
M1.7 X 6.0 (Tapping)
(
Black
)
3-080-204-31
4.0
#305: M1.4 X 4.0
(Black)
3-703-816-19
3-703-816-19
1.4
SELECTION PARTS
Ref. No.107
These parts are provided for shift and tilt adjustment. Change the thickness
(t) according to result of adjustment
(t) according to result of adjustment
4-410-539-01
SPACER PLATE (A) (t=0.10)
4-410-539-21
SPACER PLATE (A) (t=0.12)
4-410-539-41
SPACER PLATE (A) (t=0.14)
4-410-539-61
SPACER PLATE (A) (t=0.16)
4-410-539-81
SPACER PLATE (A) (t=0.18)
4-410-540-01
SPACER PLATE (B) (t=0.20)
4-410-540-21
SPACER PLATE (B) (t=0.22)
4-410-540-41
SPACER PLATE (B) (t=0.24)
Note 2: When this part is removed, adjustment is required.
For the adjustment method, refer to “Adjustment items after
replacing parts” in the Note tab of the Adjust manual.
replacing parts” in the Note tab of the Adjust manual.
Note 2: この部品を取り外したときは調整が必要です。
調整方法についてはAdjust manual の NoteタブにあるAdjust-
ment items after replacing parts を参照してください。
Note 3: Refer to “1-3. NOTES ON REMOVING/INSTALLING THE
IMAGER BOARD (CD-847 FLEXIBLE BOARD)”.
Note 3: 1-3.イメージャ基板(CD-847フレキシブル基板)の取り外し／
取り付け時の注意 を参照してください。
Note 4: Be sure to read “Precautions for Replacement of Imager” on
page 6-1 of Level 3 when changing the imager.
Note 4: イメージャの交換時はLevel 3の6-1ページ、イメージャ交換時
の注意 を必ずお読みください。
Note 5: Refer to “Assembly-4: Notes on assembling the SY Holder
Assy” when assembling.
Note 5: 組立時は Assembly-4: Notes on assembling the SY Holder Assy
を参照してください。
Note
Note 1 :
Hold the Lens Block at the
center of both sides.
center of both sides.
Do not hold the following part.
Hold here.
NOTES ON HOLDING THE LENS BLOCK
Very weak
Very weak
Very weak
Very weak
4-410-540-61
SPACER PLATE (B) (t=0.26)
4-410-540-81
SPACER PLATE (B) (t=0.28)
4-437-388-01
SPACER PLATE C (t=0.30)
4-437-388-21
SPACER PLATE C (t=0.32)
4-437-388-41
SPACER PLATE C (t=0.34)
4-437-388-61
SPACER PLATE C (t=0.36)
4-437-388-81
SPACER PLATE C (t=0.38)
4-472-511-01
SPACER PLATE D (t=0.40)
4-472-511-21
SPACER PLATE D (t=0.42)
4-472-511-41
SPACER PLATE D (t=0.44)
4-472-511-61
SPACER PLATE D (t=0.46)
4-472-511-81
SPACER PLATE D (t=0.48)
4-472-512-01
SPACER PLATE E (t=0.50)
Click on the first or last page to see other DSC-RX10 (serv.man2) service manuals if exist.