Sony DSC-QX30 Service Manual ▷ View online
DSC-QX30
3-1
3. SERVICE NOTE
3-1. PRECAUTION ON REPLACING THE SY-1046 BOARD
The board for repair is not recorded the information peculiar to a model. Therefore the following data are needed to record.
Note: The “LOAD AND WRITE” function of “ADJUSTMENT DATA BACKUP” in the DATA tab of Adjust manual performs overwrite by all data of the
set. Therefore the LOAD AND WRITE performs before carrying out following operation.
Destination Data
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
RESTORE DATA
When you replace to a board for service, get the data from the former one.
Start the Adjust Manual in the Adjust Station and execute the “RESTORE DATA” to get the data.
The data getting for this model is as follows.
Start the Adjust Manual in the Adjust Station and execute the “RESTORE DATA” to get the data.
The data getting for this model is as follows.
• PRODUCT ID & USB SERIAL No.
• Angular Velocity Sensor sensitivity
• AWB standard data input & check, Color reproduction check
• Angular Velocity Sensor sensitivity
• AWB standard data input & check, Color reproduction check
USB Serial No. and Product ID
The unit is shipped after an ID (USB Serial No.) unique to each unit and an ID (Product ID) unique to each model have been written.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID &
USB SERIAL No. INPUT” and enter these IDs.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID &
USB SERIAL No. INPUT” and enter these IDs.
Note: A newly entered Product ID is not always equal to the ID before board replacement. If the new ID differs from the previous ID, it may cause a differ-
ence from the ID registered by the customer.
Update of MAC Address
When replacing the SY board, the CPU’s unique number (MAC address) must be reloaded. Perform the following procedure to reload the
CPU’s unique number (MAC address).
1. Download the latest-version Adjust manual.
2. Install the downloaded Adjust manual.
3. Execute “Wireless LAN Setting (MAC Address)” on the ADJUST tab.
CPU’s unique number (MAC address).
1. Download the latest-version Adjust manual.
2. Install the downloaded Adjust manual.
3. Execute “Wireless LAN Setting (MAC Address)” on the ADJUST tab.
Password required for Wi-Fi connection
A password required for Wi-Fi connection is recorded in every SY board. A label to present the password to the customer is stuck to every SY
board for service. When the SY board is replaced, attach this label to the unit to be sent back.
board for service. When the SY board is replaced, attach this label to the unit to be sent back.
Note 1: The new SSID and password can be checked on the PC connected to the unit with a USB cable.
[Computer]
→ [PMHOME] → [INFO] → [WIFI_INF.TXT]
Note 2: When succeeding the data from the board before replacing to new board for repair by using The “LOAD AND WRITE” function of “ADJUST-
MENT DATA BACKUP” in the DATA tab of Adjust manual, perform following operations. The seal that is attached former board for repair is not
needed.
needed.
1. Reset the unit.
2. Download the WIFI_INF_CREATE.zip and generate “WIFI_INF.txt” file to the PMHOME folder of the unit by using the tool.
2. Download the WIFI_INF_CREATE.zip and generate “WIFI_INF.txt” file to the PMHOME folder of the unit by using the tool.
Angular Velocity Sensor
When you replace to a board for service, write down the sensitivity displayed on the angular velocity sensor (SE7701).
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity ADJ”.
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity ADJ”.
P: PITCH sensor sensitivity
Y: YAW sensor sensitivity
Type A:
Type B:
Y P
Y P
SY-1046 BOARD (SIDE B)
SE7701
(PITCH/YAW)
Note: The sensor sensitivity of SE7701 of SY-1046 board is written only service part.
– ENGLISH –
DSC-QX30
3-2
3-2. NOTES FOR FLEXIBLE BOARD
Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
OK
(The flexible board was plugged in straight
and completely)
and completely)
NG
(The flexible board was plugged in
crooked.)
crooked.)
NG
(The flexible board was not plugged in
completely.)
completely.)
Flexible
Board
Flexible
Board
Board
Connector
Connector
Reference line
Flexible
Board
Board
Connector
Connector
Flexible
Board
Reference line
Connector
Connector
Flexible
Board
Board
Flexible
Board
Reference line
Fig. 1
Fig. 2
Fig. 3
When opening the connector's holder in direction A, do not open
it with excessive force.
it with excessive force.
When closing the connector's holder, press it evenly while pushing
a flexible board in direction B.
a flexible board in direction B.
Holder
Connector
Flexible Board
A
A
Holder
Insulation side
Connector
Flexible Board
B
• Make sure that the flat cable and flexible board are not cracked
or bent at the contact end.
• Do not apply excessive force to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• The proper way to disconnect a connector is to grab the con-
nector instead of the wires. If you pull on the wires, they might
be broken.
be broken.
• The proper way to connect a connector is to grab the connector
instead of the wires. If you push on the wires, they might be
broken.
broken.
– ENGLISH –
3-3. DISCHARGING OF THE FLASH CAPACITOR
The charging capacitor for the flash has been charged at high voltage.
Therefore, there is a possibility of an electric shock if you directly handle this capacitor.
The high-voltage charge will not be discharged by simply turning off the unit’s power.
Make sure any remaining voltage is discharged by short-circuiting the flash capacitor with a Short Jig.
Therefore, there is a possibility of an electric shock if you directly handle this capacitor.
The high-voltage charge will not be discharged by simply turning off the unit’s power.
Make sure any remaining voltage is discharged by short-circuiting the flash capacitor with a Short Jig.
Preparing the Short Jig
Make a Short Jig by connecting a small clip to each lead of a resistor with a rated value of approximately 1 kΩ /1 W.
In order to prevent an electric shock, wrap insulating tape completely around the resistor and its leads.
In order to prevent an electric shock, wrap insulating tape completely around the resistor and its leads.
Resistor with a rated value of approximately
1 k
1 k
Ω/1 W (Part No. 1-215-869-11).
Wrap insulating tape completely
around the resistor and its leads.
around the resistor and its leads.
Small clip
Small clip
DSC-QX30
3-3
3-4. CHECKING THE Wi-Fi FUNCTION
Perform the following procedure to check the Wi-Fi function.
Required equipment: Windows personal computer with Wi-Fi interface
1. Turn on the power of the unit.
2. Press the Wi-Fi button of the unit.
3. Check the SSID and password by following procedure.
2. Press the Wi-Fi button of the unit.
3. Check the SSID and password by following procedure.
Procedure 1: Check the label on the inside of the battery lid.
Procedure 2: Check the seal on the cover of the manual.
Procedure 3: Connect the unit and a PC with the micro USB cable, then select [Computer] → [PMHOME] → “WIFI_INF.TXT” of
Procedure 2: Check the seal on the cover of the manual.
Procedure 3: Connect the unit and a PC with the micro USB cable, then select [Computer] → [PMHOME] → “WIFI_INF.TXT” of
[INFO].
4. Confirm on the PC that the unit is detected as a connectable wireless network.
5. To further confirm that the unit is connectable, connect the unit to the PC and select “Network and Internet” → “Manage Wireless Networks”
5. To further confirm that the unit is connectable, connect the unit to the PC and select “Network and Internet” → “Manage Wireless Networks”
from Control Panel to open the network connection list. The unit is included in the list.
DIRECT-xxxx:DSC-xxx
– ENGLISH –
DSC-QX30
3-4
3-1. SY-1046基板交換時の注意
補修用基板には機種固有の情報が記録されていないため，下記のデータを記録する必要があります。
Note: Adjust manual内のDATAタブにある「ADJUSTMENT DATA BACKUP」の機能，
「LOAD AND WRITE」 は，セットのすべてのデータを上書きす
るので，下記の作業を行う前に実施してください。
仕向けデータ
補修用基板と交換する時、補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
リストアデータ
補修用基板と交換する際，交換前の基板よりデータを取得してください。
データの取得はAdjust StationからAdjust Manualを起動させて「RESTORE DATA」を実行させてください。
本機で取得されるデータは下記になります。
データの取得はAdjust StationからAdjust Manualを起動させて「RESTORE DATA」を実行させてください。
本機で取得されるデータは下記になります。
･ PRODUCT ID & USB SERIAL No.
･ Angular Velocity Sensor sensitivity
･ AWB standard data input & check, Color reproduction check
･ Angular Velocity Sensor sensitivity
･ AWB standard data input & check, Color reproduction check
USBシリアルNo.およびプロダクトIDについて
本機はセット固有のID（USBシリアルNo.）と機種固有のID（プロダクトID）を書き込んだ後に出荷されています。
新品の補修用基板にはこれらのIDが書き込まれていないため，基板交換後にIDを入力する必要があります。
補修用基板に交換した後はAdjust StationからAdjust Manualを起動し，「PRODUCT ID & USB SERIAL No. INPUT」を実行させて
IDを入力してください。
新品の補修用基板にはこれらのIDが書き込まれていないため，基板交換後にIDを入力する必要があります。
補修用基板に交換した後はAdjust StationからAdjust Manualを起動し，「PRODUCT ID & USB SERIAL No. INPUT」を実行させて
IDを入力してください。
Note:
新しくプロダクトIDを入力すると，必ずしも基板交換前のIDと同じIDになるとは限りません。新しいIDと元のIDが違
う場合にはお客様がユーザー登録されているIDと相違が出てしまう可能性があります。
う場合にはお客様がユーザー登録されているIDと相違が出てしまう可能性があります。
MACアドレスの更新
SY基板を交換した場合，CPUの固有番号 (MACアドレス) を取り込み直す必要があります。補修用基板に交換後は下記の作業を
実施して，CPUの固有番号 (MACアドレス) を取り込み直してください。
1. 最新版のAdjust manualをダウンロードする。
2. ダウンロードしたAdjust manualをインストールする。
3. ADJUSTタブにある「Wireless LAN Setting (MAC Address)」を実施する。
実施して，CPUの固有番号 (MACアドレス) を取り込み直してください。
1. 最新版のAdjust manualをダウンロードする。
2. ダウンロードしたAdjust manualをインストールする。
3. ADJUSTタブにある「Wireless LAN Setting (MAC Address)」を実施する。
Wi-Fi接続に必要なパスワード
SY基板にはWi-Fi接続に必要なパスワードが記録されています。また，補修用SY基板にはそのパスワードをお客様へ提示するた
めのシールが付属しています。SY基板を交換した場合は，このシールを返却するセットに添付してください。
めのシールが付属しています。SY基板を交換した場合は，このシールを返却するセットに添付してください。
Note 1:
新しいSSIDとパスワードはセットとPCをUSB接続することで確認できます。
[コンピュータ] → [PMHOME] → [INFO] → [WIFI_INF.TXT]
Note 2:
Adjust manual 内のDATAタブにある「ADJUSTMENT DATA BACKUP」の機能，「LOAD AND WRITE」を使用して交換前
の基板から補修用基板にデータを引き継いだ場合は，下記の作業を実施してください。このとき補修用基板に付属し
ていたシールは不要になります。
ていたシールは不要になります。
1. セットをリセットする。
2. WIFI_INF_CREATE.zipをダウンロードしてツールを使用し，セットのPMHOMEフォルダ内に，「WIFI_INF.txt」ファイルを
2. WIFI_INF_CREATE.zipをダウンロードしてツールを使用し，セットのPMHOMEフォルダ内に，「WIFI_INF.txt」ファイルを
生成する。
角速度センサ
補修用基板と交換する時，角速度センサ（SE7701）の感度表示を書き留めてください。
Adjust StationからAdjust Manualを起動させて「Angular velocity sensor sensitivity ADJ」を実行させてください。
Adjust StationからAdjust Manualを起動させて「Angular velocity sensor sensitivity ADJ」を実行させてください。
Type A:
Type B:
Y P
Y P
SY-1046 BOARD (SIDE B)
SE7701
(PITCH/YAW)
P: PITCH 感度表示
Y: YAW 感度表示
Note：SY-1046基板のSE7701感度表示は補修用基板にしか記載されておりません。
– JAPANESE –
Click on the first or last page to see other DSC-QX30 service manuals if exist.