Sony DSC-P20 (serv.man2) Service Manual ▷ View online
2-1
SECTION 2
DISASSEMBLY
DSC-P20
•
This set can be disassembled in the order shown below.
2-1. CABINET (FRONT) ASSEMBLY
Note:
Follow the disassembly procedure in the numerical order given.
2-2. DD-158 BOARD
2
Two flexible
boards
(CN003, 004)
boards
(CN003, 004)
3
Flexible board
(CN501)
(CN501)
5
Three screws
(1.7
(1.7
×
4)
6
DD-158 board
4
Two connectors
(CN001, 002)
(CN001, 002)
1
Insulating sheet
3
Screw
(M2)
(M2)
4
Screw
(M2)
(M2)
6
Two claws
2
Screw
(M2)
(M2)
5
Four screws
(M2)
(M2)
1
Open the MS lid.
7
Cabinet (front)
assembly
assembly
2-1. CABINET (FRONT)
ASSEMBLY (Page 2-1)
2-3. CHASSIS (UPPER)
ASSEMBLY (Page 2-2)
2-2. DD-158 BOARD
(Page 2-1)
2-11. LCD MODULE
(Page 2-4)
DSC-P20
2-10. SY-66 BOARD
(Page 2-4)
2-5. BATTERY HOLDER
ASSEMBLY (Page 2-3)
2-4. FP-062 FLEXIBLE BOARD
(Page 2-2)
SERVICE POSITION
(SY-66 BOARD)
(Page 2-5)
(SY-66 BOARD)
(Page 2-5)
2-8. OPTICAL FINDER
(Page 2-3)
2-7. LENS SECTION
(Page 2-3)
2-9. LENS BLOCK ASSEMBLY
(Page 2-4)
2-6. JK-215 BOARD
(Page 2-3)
SERVICE POSITION
(DD-158 BOARD)
(Page 2-2)
(DD-158 BOARD)
(Page 2-2)
2-2
Note 1: Don t use the 12 pin flexible board of CPC-9 jig.
It causes damage to the unit.
Note 2: The old CPC-9 jig (Parts code: J-6082-393-B)
cannot be used, because it cannot operate
the adjustment remote commander.
the adjustment remote commander.
Note 3: Fastening the hook of the LENS COVER OPEN/
CLOSE switch (S202) on the JK-215 board with
tape.
tape.
Adjusting remote
commander
commander
1
1
S202
18
18
CPC-9 jig
(J-6082-393-C)
(J-6082-393-C)
Regulated power supply
(6.0 to 7.2 Vdc)
(6.0 to 7.2 Vdc)
AC power
adaptor
adaptor
AC IN
DD-158 board
[SERVICE POSITION (DD-158 BOARD)]
2-3. CHASSIS (UPPER) ASSEMBLY
1
Screw
(1.7
(1.7
×
4)
2
Screw
(1.7
(1.7
×
4)
3
FP-062
flexible board
flexible board
1
Chassis (upper)
assembly
assembly
2
Flexible board
(CN708)
(CN708)
2-4. FP-062 FLEXIBLE BOARD
2-3
2-6. JK-215 BOARD
2-5. BATTERY HOLDER ASSEMBLY
2-7. LENS SECTION
1
Screw
(1.7
(1.7
×
4)
2
Battery holder
assembly
assembly
1
JK-215 board
2
Flexible board
(CN201)
(CN201)
3
Screw
(1.7
(1.7
×
4)
4
Screw
(1.7
(1.7
×
4)
1
Flexible board
(CN101)
(CN101)
2
Flexible board
(CN181)
(CN181)
5
Lens section
Slide switch
(macro)
(macro)
Macro lever
(Note) When installing lens section, connect macro
lever with slide switch (macro).
2-8. OPTICAL FINDER
1
Two screws
(1.7
(1.7
×
4)
2
Optical finder
2-4
2-10. SY-66 BOARD
2-9. LENS BLOCK ASSEMBLY
2-11. LCD MODULE
1
Two screws
(1.7
(1.7
×
4)
2
Lens block assembly
Focus change lever
Macro lever
(Note 1) The lens block assembly is a mechanical unit
which has completely been adjusted in the
factory. So never disassemble the lens block
assembly.
factory. So never disassemble the lens block
assembly.
(Note 2) When installing lens block assembly, connect
macro lever with focus change lever.
1
Two screws
(1.7
(1.7
×
4)
2
Two screws
(1.7
(1.7
×
4)
3
Screw
(1.7
(1.7
×
4)
6
Two claws
5
Two claws
7
Plate light
guide block
guide block
8
LCD module
4
LCD frame
3
Two screws
4
Three screws
6
Two flexible boards
(CN805, 806)
(CN805, 806)
5
SY-66 board
1
Flexible board
(CN182)
(CN182)
2
Connector
(CN702)
(CN702)
Click on the first or last page to see other DSC-P20 (serv.man2) service manuals if exist.