Sony DSC-P150 (serv.man2) Service Manual ▷ View online
1-1
SECTION 1
SERVICE NOTE
DSC-P150
1-2. DISCHARGING OF THE ST-105
FLEXIBLE BOARD’S CHARGING
CAPACITOR (C550)
CAPACITOR (C550)
The charging capacitor (C550) of the ST-105 flexible board is
charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a
resistor of 1 k
resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Discharging the Capacitor
Short-circuit between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
charged capacitor with the short jig about 10 seconds.
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
Capacitor
ST
-105
1-2E
DSC-P150
Display Code
1-4. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Self-diagnosis display
• C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
• E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.
authorized Sony service facility.
1-3. NOTE IN LENS FRAME INSTALLATION
When tightening a screw, have both sides of the lens block assembly so as not for the load to depend.
M1.7
×
4
Lens frame
Lens block assembly
C:32:ss
C:13:ss
Countermeasure
Turn the power off and on again.
Format the “Memory stick”.
Insert a new “Memory Stick”.
Cause
Trouble with hardware.
Unformatted memory stick is inserted.
Memory stick is broken.
Caution Display During Error
SYSTEM ERROR
FORMAT ERROR
MEMORY STICK ERROR
E:61:ss
E:91:ss
Checking of lens drive circuit.
When failed in the focus and zoom
initialization.
initialization.
Abnormality when flash is being
charged.
charged.
Checking of flash unit or replacement
of flash unit.
of flash unit.
—
DSC-P150
2-1
2-2
2-1. FLOW CHART
The following flow chart shows the disassembly procedure.
SECTION 2
DISASSEMBLY
HELP
HELP
Note: Mic harness is connected.
Note: When you exchange rings, be sure
to follow the procedure carried on
"2-3. Exchange Method of Barrier
Assy" (2-5 page).
"2-3. Exchange Method of Barrier
Assy" (2-5 page).
1
Control switch block (RL): CN003
2
Screw (M1.4)
x3
3
Main block assy
4
Mic harness: CN707
5
Claw
x3
6
Front cabinet
7
Control switch block (RL)
1
ST-105 flexible: CN706
2
Claw
x2
3
ST-105
4
JK-266 flexible: CN704
5
Tapping screw (M1.7)
x1
6
Control switch block (SW): CN703
7
MS-207 flexible: CN751
8
SY-119
1
Screw (M1.4)
x1
2
Claw
x1
3
Claw
x2
4
Remove the Control switch block (SW)
in the direction of arrow
in the direction of arrow
A
.
1
Tapping screw (M1.7)
x3
2
Multi fixed plate
3
JK-266
4
Tapping screw (M1.7)
x1
5
MS-207
1
Ornamental ring A
2
Tapping screw (M1.2)
x2
3
Barrier assy
1
Claw
x2
2
CD-517: CN101
3
Lens block flexible: CN201
4
Lens block
6
7
1
2
4
3
1
1
2
1
2
1
4
2
1
3
1
2
3
5
3
3
3
5
5
5
2
3
1
Screw (M1.4)
x4
2
Remove the boss, pushing
A
portion.
3
Remove the rear cabinet from battery lid side.
4
Claw
x1
5
Rear cabinet
6
Panel block assy
7
LCD flexible: CN001
8
Back light flexible: CN002
6
1
4
3
8
7
2
A
A
1
1
5
4
1
2
2
4
7
8
5
6
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two
points with the short jig about 10
seconds.
Short-circuit between the two
points with the short jig about 10
seconds.
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
Capacitor
ST
-105
DSC-P150
2-3
2-4
2-2. SY-119 BOARD SERVICE POSITION
Lens block
Panel block
To turn on/off the power, short
the circuit between pin
the circuit between pin
5
and
pin
6
(GND) of CN003 on Control
switch block (SW) for 1 second.
CN003
6
5
ST-105 flexible board
MS-207 flexible board
JK-266 flexible board
SY-119 board
Control switch block (SW)
Color monitor
A/V multi cable
AC power
adaptor
adaptor
AC IN
5
1
4
3
7
6
2
A
1
1
6
7
1
2
4
3
5
5
5
2
1
1
2
3
4
3
1
2
2
4
7
8
5
6
1
2
3
3
A
1
4
2
1
3
5
Click on the first or last page to see other DSC-P150 (serv.man2) service manuals if exist.