Sony DSC-P1 (serv.man2) Service Manual ▷ View online
2-5
PD-137 board
CPC-9 jig
(J-6082-393-C)
(Note 1, 2)
(J-6082-393-C)
(Note 1, 2)
Note 1: Don’t use the 12 pin flexible board of CPC-9 jig.
It causes damage to the unit.
Note 2: The old CPC-9 jig (Parts code: J-6082-393-B)
cannot be used, because it cannot operate
the adjustment remote commander.
the adjustment remote commander.
ZM-26 board
LCD panel
SW-349 board
Adjustment remote
commander
commander
AC IN
AC power
adaptor
adaptor
2-6. LCD MODULE
1
Three screws
(M1.7)
(M1.7)
2
SW-349 board
4
Two claws
1
Screw
2
Light guide plate block
3
Two claws
5
LCD module
2-5. SW-349 BOARD
[SERVICE POSITION (LCD PANEL AND PD-137 BOARD)]
2-6
2-7. ALUMINUM CABINET (REAR) ASSEMBLY REPLACING METHOD
Adhesive sheet (A)
[Between inner cabinet (rear) assembly
and aluminum cabinet (rear) assembly]
[Between inner cabinet (rear) assembly
and aluminum cabinet (rear) assembly]
Light interception sheet (F)
1
Peel off the light interception sheet (F).
2
From the inner cabinet (rear) assembly, remove
the aluminum cabinet (rear) assembly stuck with
adhesive sheet (A) at two places.
the aluminum cabinet (rear) assembly stuck with
adhesive sheet (A) at two places.
Aluminum cabinet (rear)
assembly
assembly
adhesive sheet (A)
3
Insert new aluminum cabinet (rear) assembly,
aligning with the inner cabinet. In such a case,
make sure that the adhesive sheet (A) is affixed
on the inner cabinet side. If adhesive sheet (A)
is not present or adhesive force is reduced,
affix adhesive sheet (A) (3-064-219-01) to
the places shown below before insertion.
aligning with the inner cabinet. In such a case,
make sure that the adhesive sheet (A) is affixed
on the inner cabinet side. If adhesive sheet (A)
is not present or adhesive force is reduced,
affix adhesive sheet (A) (3-064-219-01) to
the places shown below before insertion.
LCD cover
5
Affix the LCD cover, aligning with the frame of
aluminum cabinet.
aluminum cabinet.
Note: At this time, do not touch the back of
LCD cover. The back surface with
a spcial treatment is easily affected
with the pollution.
a spcial treatment is easily affected
with the pollution.
Adhesive sheet (P)
4
Affix adhesive sheet (P), aligning with the frame
of aluminum cabinet.
of aluminum cabinet.
Light interception sheet (F)
6
As shown below, affix the light
interception sheet (F), aligning with
the positioning boss.
interception sheet (F), aligning with
the positioning boss.
2-7
2-8. INNER CABINET (REAR) ASSEMBLY REPLACING METHOD
Parallel pin (dia. 1.6
×
5)
3
Pull off the forcibly fitted parallel pin (dia. 1.6
×
5)
in the direction of arrow
A
.
A
Adhesive sheet (A)
[Between inner cabinet (rear) assembly
and aluminum cabinet (rear) assembly]
[Between inner cabinet (rear) assembly
and aluminum cabinet (rear) assembly]
Light interception sheet (F)
1
Peel off the light interception sheet (F).
2
From the aluminum cabinet (rear) assembly, remove
the inner cabinet (rear) assembly stuck with
adhesive sheet (A) at two places.
the inner cabinet (rear) assembly stuck with
adhesive sheet (A) at two places.
Inner cabinet (rear) assembly
4
Pull the jack cover off the inner cabinet (rear).
Jack cover
Inner cabinet (rear) assembly
5
Insert the jack cover into new inner
cabinet (rear) assembly.
cabinet (rear) assembly.
Jack cover
Parallel pin (dia. 1.6
×
5)
6
Forcibly fit the Parallel pin (dia. 1.6
×
5).
Aluminum cabinet (rear)
assembly
assembly
adhesive sheet (A)
7
Check if adhesive sheet (A) remains on the aluminum
cabinet side, and if so, remove it. Peel stripping sheet off
the adhesive sheet (A) at two places in the inner cabinet (rear)
assembly. Insert the inner cabinet (rear) assembly,
aligning with the aluminum cabinet.
cabinet side, and if so, remove it. Peel stripping sheet off
the adhesive sheet (A) at two places in the inner cabinet (rear)
assembly. Insert the inner cabinet (rear) assembly,
aligning with the aluminum cabinet.
Light interception sheet (F)
8
As shown below, affix the light
interception sheet (F), aligning with
the positioning boss.
interception sheet (F), aligning with
the positioning boss.
2-8
2-9. JACK COVER REPLACING METHOD
Parallel pin (dia. 1.6
×
5)
3
Pull off the forcibly fitted parallel pin (dia. 1.6
×
5)
in the direction of arrow
A
.
A
Adhesive sheet (A)
[Between inner cabinet (rear) assembly
and aluminum cabinet (rear) assembly]
[Between inner cabinet (rear) assembly
and aluminum cabinet (rear) assembly]
Light interception sheet (F)
1
Peel off the light interception sheet (F).
2
From the aluminum cabinet (rear) assembly, remove
the inner cabinet (rear) assembly stuck with
adhesive sheet (A) at two places.
the inner cabinet (rear) assembly stuck with
adhesive sheet (A) at two places.
Inner cabinet (rear) assembly
4
Pull the jack cover off the inner cabinet (rear).
Jack cover
Inner cabinet (rear) assembly
5
Insert new jack cover into the inner
cabinet (rear) assembly.
cabinet (rear) assembly.
Jack cover
Parallel pin (dia. 1.6
×
5)
6
Forcibly fit the Parallel pin (dia. 1.6
×
5).
Aluminum cabinet (rear) assembly
7
Insert the inner cabinet, aligning with the aluminum cabinet.
In such a case, if adhesive sheet (A) is not present or an adhesive
force is reduced, affix adhesive sheet (A) (3-064-219-01)
before insertion.
In such a case, if adhesive sheet (A) is not present or an adhesive
force is reduced, affix adhesive sheet (A) (3-064-219-01)
before insertion.
Light interception sheet (F)
8
As shown below, affix the light
interception sheet (F), aligning with
the positioning boss.
interception sheet (F), aligning with
the positioning boss.
Click on the first or last page to see other DSC-P1 (serv.man2) service manuals if exist.