Sony DSC-P1 (serv.man2) Service Manual ▷ View online
2-1
SECTION 2
DISASSEMBLY
DSC-P1
2-2. REAR CABINET BLOCK
(Page 2-4)
2-3. PD-137 BOARD
(Page 2-4)
2-1. BT LID ASSEMBLY
REPLACING METHOD
(Page 2-2)
(Page 2-2)
DSC-P1
2-5. SW-349 BOARD
(Page 2-5)
2-6. LCD MODULE
(Page 2-5)
SERVICE POSITION
(LCD PANEL AND PD-137 BOARD)
(Page 2-5)
(LCD PANEL AND PD-137 BOARD)
(Page 2-5)
2-4. ZM-26 BOARD
(Page 2-4)
2-7. ALMINUM CABINET (REAR)
ASSEMBLY REPLACING METHOD
(Page 2-6)
(Page 2-6)
2-8. INNER CABINET (REAR)
ASSEMBLY REPLACING METHOD
(Page 2-7)
(Page 2-7)
2-9. JACK COVER
REPLACING METHOD
(Page 2-8)
(Page 2-8)
2-10. UPPER CABINET BLOCK
(Page 2-9)
2-14. DD-150 BOARD
(Page 2-11)
2-11. PW-122 BOARD
(Page 2-9)
2-12. LENS BLOCK
(Page 2-9)
2-13. CA-66, PS-440 BOARDS
(Page 2-10)
2-15. ST-62 BOARD
(Page 2-11)
2-16. HI-74 BOARD
(Page 2-11)
2-17. MT-60 BOARD
(Page 2-11)
OVERALL CHECK
SERVICE POSITION
(Page 2-10)
SERVICE POSITION
(Page 2-10)
•
This set can be disassembled in the order shown below.
2-2
2-1. BT LID ASSEMBLY REPLACING METHOD
Note:
Follow the disassembly procedure in the numerical order given.
• ATTACHMENT OF CPC-9 JIG
PD-137 board
CN881
CN881
1
18
CPC cover
CPC-9 jig (J-6082-393-C)
(18p flexible board)
(18p flexible board)
Note 1: Don’t use the 12 pin flexible board of CPC-9 jig.
It causes damage to the unit.
Note 2: The old CPC-9 jig (Parts code: J-6082-393-B)
cannot be used, because it cannot operate
the adjustment remote commander.
the adjustment remote commander.
BT plate of BT holder assembly
having last code-1 and -2
having last code-1 and -2
BT plate of BT holder assembly
having last code-3
having last code-3
This portions are different.
[Note]
The shape of BT plate varies depending on the last code of BT holder assembly,
as shown below. The BT lid assembly for service parts (X-3951-282-1) can be
used only for the last code-3 of the BT holder assembly. For the last code-1 and
-2 of the BT holder assembly, replace the BT holder assembly.
The shape of BT plate varies depending on the last code of BT holder assembly,
as shown below. The BT lid assembly for service parts (X-3951-282-1) can be
used only for the last code-3 of the BT holder assembly. For the last code-1 and
-2 of the BT holder assembly, replace the BT holder assembly.
2-3
BT lid assembly
BT plate
Two claws
A
Note: After pulling off the BT lid assembly,
take care not to damage the aluminum cabinet
by the BT plate which will open by means of
a spring force.
by the BT plate which will open by means of
a spring force.
1
Cut off the two claws of the BT inner lid,
and pull off the BT lid assembly
in the direction of arrow
and pull off the BT lid assembly
in the direction of arrow
A
.
End face of BT plate
Two claws
B
2
Aligning with the rails of BT plate, slide
new BT lid assembly in the direction of arrow
new BT lid assembly in the direction of arrow
B
.
In such a case, slide until a click is heard, avoiding
a damage of two claws by the end face of BT plate.
a damage of two claws by the end face of BT plate.
Note: As tricks, slide the BT lid assembly obliquely
by the amount of a play to the BT plate as shown
in the figure, taking care not to damage the two claws.
in the figure, taking care not to damage the two claws.
BT plate end face
Claw
2-4
2-3. PD-137 BOARD
2-4. ZM-26 BOARD
3
Two screws
(M1.7)
(M1.7)
2
Three screws
(M1.7)
(M1.7)
4
PD-137 board
6
Flexible board
(ZM-26 board)
(CN882)
(ZM-26 board)
(CN882)
1
Two flexible boards
(CN805, 806)
(CN805, 806)
5
Flexible board
(SW-349 board)
(CN884)
(SW-349 board)
(CN884)
1
Two screws
(M1.7)
(M1.7)
2
ZM sheet metal
3
ZM-26 board
2-2. REAR CABINET BLOCK
7
Rear cabinet block
2
Screw
(M1.7)
1
Screw
(M1.7)
(M1.7)
3
Screw
(M1.7)
(M1.7)
6
Flexible board
(MT-60 board)
(CN883)
(MT-60 board)
(CN883)
5
Cabinet (front)
assembly
assembly
4
Two screws
(M1.7)
(M1.7)
Click on the first or last page to see other DSC-P1 (serv.man2) service manuals if exist.