Sony DSC-L1 (serv.man13) Service Manual ▷ View online
DSC-L1
2. DESMOTAGEM
2-3
2-4
AJUDA
1
MS-238 flexible: CN101
2
Tapping screw (M1.7)
x1
3
Claw
x1
4
ST-109 flexible: CN705
5
SY-110
1
CD-526 flexible: CN704
2
Lens block flexible: CN201
3
Claws
x2
4
Lens block
1
Claws
x2
2
ST-109 flexible
3
Copper leaf sheet (BT)
4
Lock ace screw (M1.4)
x1
5
Tripod holder
6
MS holder
7
Claws
x2
8
MS-238 flexible
2
8
4
1
1
4
7
7
3
5
6
1
2
3
3
Note: The cautions at the time of lens block handling
In case you deal with a lens block, be careful of the following things.
from Page 2-2
Touch the flexible board of motor side recklessly or
don’t bend it., because the mounted chip parts could
be peeled if the flexible board is curved.
don’t bend it., because the mounted chip parts could
be peeled if the flexible board is curved.
CD-526 flexible board is integrated with the lens block.
Do not touch or separate the CD board.
CD-526 flexible board becomes only exchange by lens block.
Do not touch or separate the CD board.
CD-526 flexible board becomes only exchange by lens block.
Have the portion of upper and
lower arrows with two fingers.
lower arrows with two fingers.
5
1
2
4
3
DSC-L1
2. DESMONTAGEM
2-2. POSIÇÃO DO SERVIÇO
2-5
2-6
SY-110 board
ST-109 flexible board
MS-238 flexible board
Cabinet (upper) block
Lens block
Cabinet (rear) block
Cabinet (front) block
5
1
3
2
3
4
4
1
2
3
3
2
8
4
1
1
7
7
3
5
6
AC power
adaptor
adaptor
DC IN
5
1
2
4
3
5
qf
wa
3
qd
qg
6
7
9
6
qh
qk
w;
w;
qj
ql
8
0
4
qa
3
2
1
qs
DSC-L1
2. DESMONTAGEM
2-3. O METODO DE FIXAÇÃO DO LC-084 PLACA FLEXIVEL
2-7
2-8
1
Insert the plate of lens cover motor
in the slot on the front cabinet.
in the slot on the front cabinet.
2
Insert the gear of lens cover motor, as you don’t
collide with the gear of lens cover.
collide with the gear of lens cover.
7
Check that the LC-084 flexible board has fitted into eight claws exactly.
3
As you make the right rotate the gear of lens cover
motor, engage with the gear of lens cover.
motor, engage with the gear of lens cover.
4
Tapping screw (M1.7)
6
Tapping screw (M1.7)
5
Assemble after pushing up the S401
of LC-084 flexible board upwards.
If it assembles then, the tip of S401
will break.
of LC-084 flexible board upwards.
If it assembles then, the tip of S401
will break.
S401
(Open detect switch)
(Open detect switch)
Claw
Claw
precision screw driver, etc.
Claw
Claw
Claw
Claw
Claw
Claw
2-9
DSC-L1
2. DESMONTAGEM
2-4. O METODO DE FIXAÇÃO DOS JACKS DE USB E DC IN NA PLACA FLEXIVEL - JK-276
The cabinet (right) cannot be installed unless the USB and DC IN
jacks are mounted vertically on the JK-276 board.
Confirm that the USB and DC IN jacks are mounted vertically when
they were replaced (jacks will not tilt in horizontal direction).
Also, no confirmation is necessary if the JK-276 board is purchased
by the code A.
jacks are mounted vertically on the JK-276 board.
Confirm that the USB and DC IN jacks are mounted vertically when
they were replaced (jacks will not tilt in horizontal direction).
Also, no confirmation is necessary if the JK-276 board is purchased
by the code A.
USB jack
DC IN jack
OK
NG
USB jack
DC IN jack
Click on the first or last page to see other DSC-L1 (serv.man13) service manuals if exist.