Sony DSC-L1 (serv.man13) Service Manual ▷ View online
1-1
DSC-L1
1-2. DESCARREGAMENTO DO CAPACITOR
(C050) DA PLACA ST-109
The charging capacitor (C050) of the ST-109 flexible board is
charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a
resistor of 1 k
resistor of 1 k
Ω
/1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Discharging the Capacitor
Short-circuit between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
charged capacitor with the short jig about 10 seconds.
1-1. NOTA PARA REPARO
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
1. NOTA DE SERVIÇO
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
1-2E
DSC-L1
Display Code
1-4. DESCRIÇÃO SOBRE AUTO-DIAGNÓSTICO VISUALIZADO
Self-diagnosis display
• C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
• E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.
authorized Sony service facility.
C:32:ss
C:13:ss
Countermeasure
Turn the power off and on again.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Cause
Trouble with hardware.
Unformatted “Memory Stick Duo” is
inserted.
inserted.
“Memory Stick Duo” is broken.
Caution Display During Error
SYSTEM ERROR
FORMAT ERROR
MEMORY STICK ERROR
E:61:ss
E:91:ss
Checking of lens drive circuit.
When failed in the focus and zoom
initialization.
initialization.
Abnormality when flash is being
charged.
charged.
Checking of flash unit or replacement
of flash unit.
of flash unit.
—
1-3. NOTA SOBRE INSTALAÇÃO DA LENTE
In case you deal with a lens block, be careful of the following things.
Touch the flexible board of motor side recklessly or
don’t bend it., because the mounted chip parts could
be peeled if the flexible board is curved.
don’t bend it., because the mounted chip parts could
be peeled if the flexible board is curved.
CD-526 flexible board is integrated with the lens block.
Do not touch or separate the CD board.
CD-526 flexible board becomes only exchange by lens block.
Do not touch or separate the CD board.
CD-526 flexible board becomes only exchange by lens block.
Have the portion of upper and
lower arrows with two fingers.
lower arrows with two fingers.
DSC-L1
Link
Link
2. DESMONTAGEM
LOCALIZAÇÃO DAS PLACAS DE CIRCUITO
POSIÇÃO DO SERVIÇO
O METODO DE FIXAÇÃO DO JACK DOS USB E DC IN NA PLACA FLEXIVEL - JK-276
AJUDA
O METODO DE FIXAÇÃO DO LC-084 PLACA FLEXIVEL
DESMONTAGEM
DSC-L1
2.
DESMOTAGEM
2-1
2-2
The following flow chart shows the disassembly procedure.
2-1. PROCEDIMENTO
2. DESMONTAGEM
HELP
HELP
to Page 2-3
When you disassemble the LC-084 flexible board,
assemble with refer to page 2-7 " The method of
attachment of LC-084 flexible board ".
assemble with refer to page 2-7 " The method of
attachment of LC-084 flexible board ".
When you disassemble USB and DC IN jacks on
the JK-276 flexible board, assemble with refer
to page 2-9 " The method of attachment of USB
and DC IN jacks on the JK-276 flexible board ".
the JK-276 flexible board, assemble with refer
to page 2-9 " The method of attachment of USB
and DC IN jacks on the JK-276 flexible board ".
1
Open the jack cover.
2
Lock ace screws (M1.4)
x2
3
Lock ace screws (M1.4)
x2
4
Claw
x1
5
Cabinet (right) assy
6
Lock ace screws (M1.4)
x2
7
Slide the BT lid.
8
Lock ace screw (M1.4)
x1
9
Open the BT lid.
0
Lock ace screw (M1.4)
x1
qa
Claw
x1
qs
Claw
x1
qd
LC-084 flexible: CN202
qf
Cabinet (front) block
qg
Protection sheet (SW)
qh
SW-432 flexible: CN701
qj
Back light flexible: CN804
qk
LCD flexible: CN806
ql
Lock ace screw (M1.4)
x1
w;
Claws
x2
wa
Cabinet (rear) block
1
Tapping screws (M1.7)
x3
2
Claw
x1
3
SW-432 flexible
4
Panel block
1
Tapping screws (M1.7)
x2
2
Claws
x9
3
LC-084 flexible
1
JK-276 flexible: CN702
2
Tapping screw (M1.7)
x1
3
Claws
x2
4
Claw
x1
5
Cabinet (upper) block
5
qf
3
5
3
4
wa
3
qd
qg
6
7
9
1
1
1
2
6
qh
qk
w;
w;
qj
ql
8
0
4
qa
3
2
1
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two
points with the short jig about 10
seconds.
Short-circuit between the two
points with the short jig about 10
seconds.
5
1
3
2
3
4
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
qs
1
Lock ace screw (M1.4)
x1
2
Claws
x3
3
Speaker harness
4
Speaker connector
5
JK-276 flexible
2
2
2
3
4
1
1
2
2
2
2
2
2
2
2
2
Click on the first or last page to see other DSC-L1 (serv.man13) service manuals if exist.