Sony DSC-J10 Service Manual ▷ View online
DSC-J10
2-2
Wrap insulating tape.
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, do not pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, do not press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
The charging capacitor is charged up to the maximum 310 V
potential.
There is a danger of electric shock by this high voltage
when the capacitor is handled by hand. The electric shock
is caused by the charged voltage which is kept without dis-
charging when the main power of the unit is simply turned
off. Therefore, the remaining voltage must be discharged as
described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end
of a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
DISCHARGING OF THE CHARGING CAPACITOR
Cut and remove the part of gilt
which comes off at the point.
(Be careful of that some
pieces of gilt may be left inside)
Make sure to remove
the battery before
Discharging the Capacitor.
ST Board
Note:
Note:
High-voltage cautions
High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points with the
short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
Short-circuit between the two points with the
short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
R:1 kΩ/1 W
(Part code: 1-215-869-11)
DSC-J10
2-3
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
ns: not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
DISASSEMBLY
1
USB Connector Open (
1
) → #S1 / #S2 X 2 → #S1 / #S2 X 1 → #S3 / #S4 X 2
4
Remove the Switch Assy (
4
)
5
#S6 X 2 → Remove the Cushion (
5
)
1. Remove to numerical order (
1
to
6
) in the left figure.
Note
DISCHARGING OF THE CHARGING CAPACITOR
1
X-2580-781-1 COVER ASSY, FRONT (WHITE)
1
X-2580-782-1 COVER ASSY, FRONT (BLACK)
1
X-2580-783-1 COVER ASSY, FRONT (RED)
1
X-2580-784-1 COVER ASSY, FRONT (ORANGE)
1
X-2580-785-1 COVER ASSY, FRONT (BLUE)
2
X-2580-780-1 COVER ASSY, REAR
3
4-274-007-01 CUSHION (SW)
4
A-1813-385-A SW BOARD (Note2)
5
1-802-984-11 LCD MODULE (Note2)
6
X-2580-786-1 SWITCH ASSY (WHITE)
6
X-2580-787-1 SWITCH ASSY (BLACK)
6
X-2580-788-1 SWITCH ASSY (RED)
6
X-2580-789-1 SWITCH ASSY (ORANGE)
6
X-2580-790-1 SWITCH ASSY (BLUE)
7
4-274-011-01 CUSHION (1)
8
4-274-012-01 CUSHION (2)
0
9
1-756-765-13 BATTERY PACK (SP60BPRA9C)
10
4-274-000-01 LID, BT INNER
#S1
4-273-996-01 SCREW_M_1.4_3_BLK_AB (Note1)
#S2
4-273-997-01 SCREW_M_1.4_3_SVR_AB (Note1)
#S3
4-273-998-01 SCREW_M_1.4_4_BLK_AB (Note1)
#S4
4-273-999-01 SCREW_M_1.4_4_SVR_AB (Note1)
#S6
4-274-006-01 SCREW_TP_1.4_2_SVR_AB
Note1: THE COMBINATION OF CABINET’S COLOR AND SCREW
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer
to Table 2-1.
Table 2-1
Screw's
Ref. No. (Parts Color.)
Cabinet's Color
#S2, #S4 (Silver)
WHITE, RED,
ORANGE, BLUE
#S1, #S3 (Black)
BLACK
Back View
Front View
#S6
Cushion
Caution
Danger of explosion occurs if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Front View
Open
Left View
Right View
Bottom View
#S3
#S4
#S1
#S2
#S1
#S2
Note2: Refer to “Assembly-1: Handling Method for the Flexible
Boards of the LCD Module and SW Board” when you
assemble.
Note3: These parts are not supplied. Take care that do not damage
them when removing.
2�
1
2
1
#S6
3
3�
9
6�
5
(Note2)
5�
4
(Note2)
4
6
ns
5
(Note3)
ns
(Note3)
Main Board Section
(See Page 2-4)
2(Claw)
1
#S1
#S2
(Note1)
#S1
#S2
(Note1)
#S3
#S4
(Note1)
4
10
A
B
A
B
DSC-J10
2-4
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
2-1-2. MAIN BOARD SECTION
DISASSEMBLY
1. Remove to numerical order (
7
to
qs
) in the left figure.
51
4-274-001-01 HOLDER, USB
52
4-274-007-01 CUSHION (SW)
53
4-274-004-01 SPRING, USB COVER
54
4-274-003-01 COVER, USB (WHITE) (Note1)
54
4-274-003-11 COVER, USB (BLACK) (Note1)
54
4-274-003-21 COVER, USB (RED) (Note1)
54
4-274-003-31 COVER, USB (ORANGE) (Note1)
54
4-274-003-41 COVER, USB (BLUE) (Note1)
55
4-274-005-01 SPRING, USB JACK
56
A-1813-422-A JACK, USB (WHITE) (Note2)
56
A-1813-423-A JACK, USB (BLACK) (Note2)
56
A-1813-424-A JACK, USB (RED) (Note2)
56
A-1813-425-A JACK, USB (ORANGE) (Note2)
56
A-1813-426-A JACK, USB (BLUE) (Note2)
57
4-274-019-01 PLATE (D), GROUND
58
4-274-009-01 SHAFT (STRAP)
59
A-1813-429-A SPEAKER (Note3)
60
X-2580-791-1 LEVER ASSY, ZOOM (WHITE)
60
X-2580-792-1 LEVER ASSY, ZOOM (BLACK)
60
X-2580-793-1 LEVER ASSY, ZOOM (RED)
60
X-2580-794-1 LEVER ASSY, ZOOM (ORANGE)
60
X-2580-795-1 LEVER ASSY, ZOOM (BLUE)
61
A-1816-072-A ST BOARD
62
X-2580-796-1 BRACKET ASSY, LCD
63
1-856-181-11 OPTICAL UNIT (BE0032)
64
A-1813-408-A CCD BLOCK ASSY
65
4-274-020-01 CHASSIS
66
4-274-016-01 PLATE (A), GROUND
67
4-274-017-01 PLATE (B), GROUND
68
4-274-018-01 PLATE (C), GROUND
69
A-1813-427-A MICROPHONE (Note4)
70
4-274-010-01 PLATE, MICROPHONE GROUND
71
A-1813-428-A MAIN BOARD, COMPLETE
72
4-274-012-01 CUSHION (2)
73
4-274-011-01 CUSHION (1)
0
F1
1-576-415-11 FUSE, MICRO (1608 TYPE) (2A/32V)
0
F2
1-576-415-11 FUSE, MICRO (1608 TYPE) (2A/32V)
#S2
4-273-997-01 SCREW_M_1.4_3_SVR_AB
#S5
4-274-002-01 SCREW_TP_1.4_3_SVR_AB
#S7
4-274-013-01 SCREW_TP_1.2_3.5_SVR_AB
7
#S2 X 1 → #S5 X 1
Front View
#S5
#S2
Note
Note1: Refer to “Assembly-2: Assembling Method of the USB Cover”
when you assemble.
Note2: Refer to “Assembly-3: Assembling Method of the USB Jack”
when you assemble.
Note3: Refer to “Assembly-4: Routing and Soldering Method of the
Speaker Lead Wire” when you assemble
.
Note4: Refer to “Assembly-5: Soldering Method of the Microphone
Lead Wire” when you assemble
.
8
#S5 X 2
qa
Unsolder (
qa
-1
) → Unsolder (
qa
-2
) → #S5 X 4
0
Unsolder (
0
) → #S5 X 4
Back View
#S5
Back View
Top View
#S5
Solder
Front View
qa
-1
qa
-2
#S5
#S5
51
7
54
(Note1)
(Note2)
56
61
0
qa�
71
73
72
63
9
64
#S5
(Note3)
#S2
#S5
#S5
52
53
55
70
69
(Note4)
59
58
57
68
67
66
#S7
65
qs
F2 F1
8�
62
60
#S5
#S5
11(Solder)
qa
-1
qa
-1
11(Solder)
qa
-2
qa
-2
10(Solder)
DSC-J10
2-5E
Checking supplied accessories.
CD-ROM
- Cyber-shot application software
- “Cyber-shot User Guide”
4-266-075-01
Wrist strap
2-050-981-01
Instruction Manual
・ (Only for destination Japanese model)
AC adaptor
(AC-UB10)
0
1-489-282-21 (US)
0
1-489-282-31 (CH)
Power cord (mains lead)
(EXCEPT US, CH)
0
1-836-411-21 (JE)
0
1-837-421-11 (UK, HK)
0
1-837-424-11 (TW)
0
1-837-427-11 (AEP, E)
0
1-838-951-11 (AR)
0
1-838-954-11 (KR)
Dedicated USB cable
1-836-378-51
Conversion (2P) Adaptor
0
1-569-008-12
(E (Latin America))
Conversion (2P) Adaptor
0
1-569-007-12 (JE)
AC adaptor
(AC-UB10)
0
1-489-282-61
(EXCEPT US, CH)
∗ 4-265-841-11 (ENGLISH)
∗ 4-265-841-21 (FRENCH)
∗ 4-265-841-31 (ITALIAN)
∗ 4-265-841-41 (SPANISH)
∗ 4-265-841-51 (PORTUGUESE)
∗ 4-265-841-61 (GERMAN)
∗ 4-265-841-71 (DUTCH)
∗ 4-265-841-81 (TRADITIONAL CHINESE)
∗ 4-265-841-91 (SIMPLIFIED CHINESE)
∗ 4-265-846-11 (RUSSIAN)
∗ 4-265-846-21 (ARABIC)
∗ 4-265-846-31 (PERSIAN)
∗ 4-265-846-41 (KOREAN)
∗ 4-265-846-51 (POLISH)
∗ 4-265-846-61 (CZECH)
∗ 4-265-846-71 (HUNGARIAN)
∗ 4-265-846-81 (SLOVAK)
∗ 4-265-846-91 (SWEDISH)
∗ 4-265-847-11 (FINNISH)
∗ 4-265-847-21 (NORWEGIAN)
∗ 4-265-847-31 (DANISH)
∗ 4-265-847-41 (THAI)
∗ 4-265-847-51 (MALAY)
∗ 4-265-847-61 (TURKISH)
∗ 4-265-847-71 (GREEK)
∗ 4-265-847-81 (UKRAINIAN)
∗ 4-265-847-91 (CROATIAN)
∗ 4-265-848-11 (ROMANIAN)
∗ 4-265-848-21 (INDONESIAN)
∗ 4-265-848-31 (BRAZILIAN PORTUGUESE)
4-266-072-11 (SIMPLIFIED CHINESE)
4-266-073-11 (ENGLISH)
∗ 4-266-073-21 (ENGLISH, SPANISH)
∗ 4-266-073-31 (ENGLISH, FRENCH)
∗ 4-266-073-41 (ENGLISH, RUSSIAN, UKRAINIAN)
∗ 4-266-073-51 (ENGLISH, FRENCH, ITALIAN, SPANISH, PORTUGUESE,
GERMAN, DUTCH, TURKISH, GREEK, POLISH, CZECH,
HUNGARIAN, SLOVAK, SWEDISH, FINNISH, NORWEGIAN,
DANISH, CROATIAN, ROMANIAN)
∗ 4-266-073-61 (ENGLISH, TRADITIONAL CHINESE, SIMPLIFIED CHINESE,
INDONESIAN, ARABIC, PERSIAN, THAI)
∗ 4-266-073-71 (ENGLISH, SPANISH, PORTUGUESE)
∗ 4-266-073-81 (ENGLISH, TRADITIONAL CHINESE, SIMPLIFIED CHINESE,
INDONESIAN, ARABIC, PERSIAN)
∗ 4-266-073-91 (ENGLISH, SPANISH, PORTUGUESE, TRADITIONAL CHINESE,
SIMPLIFIED CHINESE, KOREAN)
∗ 4-266-074-11 (ENGLISH, TRADITIONAL CHINESE, SIMPLIFIED CHINESE)
4-266-074-21 (KOREAN)
∗ 4-266-074-31 (SPANISH, PORTUGUESE)
∗ 4-266-074-41 (ENGLISH, ARABIC, PERSIAN)
∗ 4-266-074-51 (ENGLISH, TRADITIONAL CHINESE)
Cyber-shot User Guide (HTML)
About Cyber-shot User Guide (HTML)
This CD-ROM is provided in HTML.
Therefore, it is suitable for browsing on the PC, but is not suitable for printing.
The printed matter is not supplied.
The following lists part numbers of languages.
The CD-ROM supplied contains all of language version.
英語・韓国語・中国語のみ部品供給可能です。
DSC-J10
User Guide
User Guide
Use this manual if you encounter any problems, or have any questions about the camera.
Click on the first or last page to see other DSC-J10 service manuals if exist.