Sony DSC-HX200 / DSC-HX200V (serv.man2) Service Manual ▷ View online
DSC-HX200/HX200V_L2
2-5
2-1-3. LENS SECTION
1. Remove to numerical order (
1
to
3
) in the left figure.
DISASSEMBLY
#155
When disassembly and re-assembly this
block, must open the flash.
block, must open the flash.
#12
#155
#30
Cabinet (Front) section
(See page 2-8)
2
Cabinet (Upper) Section
(See page 2-6)
1
101
103
(Note 1)
104
(Note 3)
105
106
(including CP001
(CMOS imager))
(Note 2)
(CMOS imager))
(Note 2)
107
102
108
109
(Note 4)
3
(Claws)
(Note 4)
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
1-856-156-11
OPTICAL UNIT (NY213B)
(Note 4)
102
4-284-296-01 SHEET,
PD
103
4-276-127-01
MASK (NY213B) (Note 1)
104
1-856-188-31
FILTER BLOCK, OPTICAL (Note 3)
105
4-258-931-01
RUBBER (NY213B), SEAL
106
A-1864-704-A CD-814 BOARD, COMPLETE
(including CP001 CMOS imager) (Note 2)
107
1-882-898-11
CN-470 FLEXIBLE BOARD
108
4-284-293-01
SHEET (LENS), RADIATION
109
4-284-294-01 GASKET
(CMOS)
(Note 4)
#12
3-080-204-21 SCREW,
TAPPING,
P2
#30
3-086-156-11 SCREW
B1.2
#155 3-080-204-31 SCREW,
TAPPING,
P2
Screw
Note
Note 1: Refer to “Assembly-1: Installation Cautions of the Mask
(NY213B).”.
Note 1:
Assembly-1: Installation Cautions of the Mask (NY213B).
を参照してください。
DISCHARGING OF THE CHARGING CAPACITOR
ストロボ用充電コンデンサの放電
3
Note 2: Be sure to read “Precautions for Replacement of Imager”
on page 6-1 of Level 3 when changing the imager.
Note 2: イメージャの交換時はLevel 3の6-1ページ、 イメージャ
交換時の注意 を必ずお読みください。
1
#155 X 4 → Open Flash
#155
Back View
2
#12 X 2
#12
Back View
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
#30: M1.2 X 3.5 (Tapping)
(White)
3-086-156-11
3-086-156-11
3.5
1.2
1.7
6.0
#155: M1.7 X 6.0 (Tapping)
(Black)
3-080-204-31
3-080-204-31
Note 3: Refer to “Assembly-7: How to distinguish the side of Optical
Filter Block facing to Lens Device.”.
Note 3: Assembly-7: How to distinguish the side of Optical Filter
Block facing to Lens Device. を参照してください。
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2012.05
Note 4: When this part is removed, adjustment is required.
For the adjustment method, refer to "Adjustment items after
replacing parts" in the Note tab of the Adjust manual.
replacing parts" in the Note tab of the Adjust manual.
Note 4: この部品を取り外したときは調整が必要です。
調整方法については Adjust manual の Noteタブにある
Adjustment items after replacing parts を参照してください。
Adjustment items after replacing parts を参照してください。
DSC-HX200/HX200V_L2
2-6
2-1-4. CABINET (UPPER) SECTION
ns: not supplied
HX200V
HX200V
ST section
(See page 2-7)
(Note 2)
154
(Note 3
, 4
)
151
152
153
#12
#12
#12
ST section
(See page 2-7)
(Note 2)
#3
#3
ns
ns
ns
155
161
156
157
(Note 4)
158
(Note 4)
159
(Note 1
, 4
)
160
Adjust the position.
Check whether the zoom
lever turn to the T/W side.
lever turn to the T/W side.
(Claws)
(Claws)
Do not touch this part.
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
151
4-279-810-01
FRAME (R), STRAP
152
4-279-809-01
SHEET METAL (R), STRAP
153
A-1872-527-A GP-056 BOARD, COMPLETE (SERVICE) (HX200V)
154
X-2583-791-1 CABINET (UPPER) ASSY (370) (HX200V) (Note 3
, 4
)
154
X-2583-792-1 CABINET (UPPER) ASSY (361) (HX200) (Note 3
, 4
)
155
4-279-806-01 CUSHION
(MICROPHONE)
156
4-279-807-01
PLATE, MODE (CH)
156
4-279-807-11
PLATE, MODE (EXCEPT CH)
157
1-489-561-21
SWITCH BLOCK, CONTROL (SW63370)
(Note 4)
158
4-279-808-01 CUSHION
(AF)
(Note 4)
159
A-1821-592-A RL-110 FLEXIBLE BOARD, COMPLETE (Note 1
, 4
)
160
4-279-805-01 RETAINER,
AF
161
1-542-862-31 MICROPHONE
UNIT
#3
2-660-401-01
SCREW (M1.7), NEW TRU-STAR, P2 (HX200V)
#12
3-080-204-21 SCREW,
TAPPING,
P2
Note
Note 1: Refer to “Assembly-2: Installation Cautions of the RL-110
Flexible Board.”.
Note 1: Assembly-2: Installation Cautions of the RL-110 Flexible
Board. を参照してください。
Note 2: Refer to “Assembly-4: Route the Flash Harnesses.”.
Note 2: Assembly-4: Route the Flash Harnesses. を参照してください。
Screw
#3: M1.7 X 2.5
(Red)
2-660-401-01
2-660-401-01
2.5
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
Note 3:
GPS logo
When replacing this part, be careful
whether a LOGO is existed or not.
whether a LOGO is existed or not.
X-2583-791-1
X-2583-792-1
GPSのロゴ
Note 3:
X-2583-791-1
X-2583-792-1
交換時にロゴの有無に注意してくだ
さい。
さい。
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2012.05
Note 4: When this part is removed, adjustment is required.
For the adjustment method, refer to "Adjustment items after
replacing parts" in the Note tab of the Adjust manual.
replacing parts" in the Note tab of the Adjust manual.
Note 4: この部品を取り外したときは調整が必要です。
調整方法については Adjust manual の Noteタブにある
Adjustment items after replacing parts を参照してください。
Adjustment items after replacing parts を参照してください。
DSC-HX200/HX200V_L2
2-7
2-1-5. ST SECTION
1. The meaning of the sign in left figure is as follows. Be careful when it removes.
◇-X
: Solder
DISASSEMBLY
HX200
#12
#12
BH001
210
206
207
203
208
(Note 1)
205
(Note 1)
204
(Note 1)
209
(Note 1)
201
(Note 2)
202
C901
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
201
X-2582-949-1 BTH ASSY (370) (US, UK, CH, J) (Note 2)
201
X-2583-790-1 BTH ASSY (361) (EXCEPT US, UK, CH, J) (Note 2)
202
A-1864-706-A ST-276 FLEXIBLE BOARD, COMPLETE
203
4-279-821-01 COVER,
BT
TERMINAL
204
4-279-812-11
COVER, ST (Note 1)
205
1-487-161-21
FLASH UNIT (Note 1)
206
X-2581-251-1 BASE
ASSY,
ST
207
A-1864-705-A PL-056 FLEXIBLE BOARD, COMPLETE
208
1-455-061-11
SOLENOID, PLUNGER (Note 1)
209
4-279-811-01
HOLDER, PL (Note 1)
210
4-279-792-01
SHEET (LCD) (HX200)
C901 1-116-820-11 CAP,
ALUMINIUM
ELECT 214uF
315V
BH001 1-780-064-21 BATTERY
TERMINAL
BOARD
#12
3-080-204-21 SCREW,
TAPPING,
P2
Screw
Note
Note 1: Refer to “Assembly-3: The Method of installation of the
ST section.”.
Note 1: Assembly-3: The Method of installation of the ST section.
を参照してください。
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
When replacing this part, be careful whether
a LOGO is existed or not.
a LOGO is existed or not.
X-2582-949-1
X-2583-790-1
Note 2:
TransferJet logo
X-2582-949-1
X-2583-790-1
TransferJet のロゴ
交換時にロゴの有無に注意してください。
Note 2:
DSC-HX200/HX200V_L2
2-8
2-1-6. CABINET (FRONT) SECTION
#12
251
254
252
253
259
256
255
257
(Note)
258
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
251
X-2583-794-1 RING ASSY (370), LENS
252
A-1864-702-A SE-183 BOARD, COMPLETE
253
1-967-758-11
CABLE, FLEXIBLE FLAT
254
4-279-792-01 SHEET
(LCD)
255
4-279-791-01
PLATE, MF GROUND
256
4-419-725-01
RING (MK), ORNAMENTAL
257
X-2583-793-1 CABINET (FRONT) ASSY (370)
(Note)
258
4-279-790-01 PLATE,
TRIPOD
259
4-142-509-01 FOOT,
RUBBER
#12
3-080-204-21 SCREW,
TAPPING,
P2
Screw
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2012.05
Note: When this part is removed, adjustment is required.
For the adjustment method, refer to "Adjustment items after
replacing parts" in the Note tab of the Adjust manual.
replacing parts" in the Note tab of the Adjust manual.
Note: この部品を取り外したときは調整が必要です。
調整方法については Adjust manual の Noteタブにある
Adjustment items after replacing parts を参照してください。
Adjustment items after replacing parts を参照してください。
Note
Click on the first or last page to see other DSC-HX200 / DSC-HX200V (serv.man2) service manuals if exist.