Sony DSC-HX200 / DSC-HX200V (serv.man2) Service Manual ▷ View online
DSC-HX200/HX200V_L2
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
Link
ACCESSORIES
DISCHARGING OF THE CHARGING CAPACITOR
ASSEMBLY
MS-
485
SY
-320
1
Rear Section
• PD-466 Board
• PD-441 Flexible Board
7
Cabinet (Front) Section
• SE-183 Board
3
MS-485 Board
6
Cabinet (Upper) Section
• GP-056 Board (HX200V)
• PL-056 Flexible Board
• RL-110 Flexible Board
• ST-276 Flexible Board
2
EVF Block
• SE-181 Flexible Board
5
Lens Section
• CD-814 Board
• CN-470 Flexible Board
4
Boards Section
• SY-320 Board
• MS-463 Flexible Board
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original
• -XX, -X mean standardized parts, so they may have some differences from the original
one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not sup-
plied.
• Due to standardization, replacements in the parts list may be different from the parts
specified in the diagrams or the components used on the set.
• CAPACITORS:
uF:
uF:
μF
• COILS
uH:
uH:
μH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
nonflammable
• SEMICONDUCTORS
In each case, u: μ, for example:
uA...:
In each case, u: μ, for example:
uA...:
μA... , uPA... , μPA... ,
uPB...
,
μPB... , μPC... , μPC... ,
uPD...,
μPD...
The components identified by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
le numéro spécifié.
• Color Indication of Appearance Parts
Example:
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は, 補修用部品であるため, 回路図及び
セットに付いている部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
金 被:金属被膜抵抗。
サンキン:酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。
セットに付いている部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
金 被:金属被膜抵抗。
サンキン:酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。
0印の部品,または0印付の点線で囲ま
れた部品は,安全性を維持するために,
重要な部品です。
従って交換時は,必ず指定の部品を使用
してください。
れた部品は,安全性を維持するために,
重要な部品です。
従って交換時は,必ず指定の部品を使用
してください。
• 外装部品色表示
例:
(SILVER) :セットの色を表す。
(Silver) :部品の色を表す。
• Abbreviation
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
J :
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
J :
Japanese model
JE : Tourist Model
KR : Korea model
TW : Taiwan model
KR : Korea model
TW : Taiwan model
View Position
Right View
Left View
Front View
Bottom View
Top View
Back View
DSC-HX200/HX200V_L2
2-2
– ENGLISH –
– JAPANESE –
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked
of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, don’t press down at wire of con-
nector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE CHARGING
CAPACITOR (C901)
CAPACITOR (C901)
The charging capacitor is charged up to the maximum 315 V
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω/1 W
Wrap insulating tape.
1 k
Ω/1 W
Wrap insulating tape.
R:1 k
Ω/1 W
C901
ST-276 Flexible
Board
Board
ST-276 Flexible
Board
Board
C901
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.
Short-circuit between two points with
the short jig about 10 seconds.
(Part code: 1-215-869-11)
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け,
折れ等がないことを確認する。
また,コネクタへの接続は,差し込み不足や斜め差しになら
ないように注意する。
• コネクタを取り外す時に,線材部(極細)を持って引っ張ると
断線する恐れがありますので,絶対に線材部(極細)を持って
引っ張らないでください。
引っ張らないでください。
• 線材部(極細)を押さえながらコネクタを差し込むと,線材部
(極細)が断線する恐れがありますので,絶対に線材部(極細)
には負担をかけないでください。
• 金メッキされているフレキシブル基板には,強い負担をかけ
ないでください。
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
ストロボ用充電コンデンサ(C901)の放電
ストロボ用充電コンデンサは最大315Vの電圧で充電され
ています。
この高電圧で充電されたコンデンサに手を触れた場合,
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
ています。
この高電圧で充電されたコンデンサに手を触れた場合,
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
ショート治具の準備
ショート治具は1kΩ/1W抵抗 (1-215-869-11)
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
R:1 k
Ω/1 W
(部品コード:1-215-869-11)
コンデンサの放電
フラッシュユニットの電源コンデンサ
の端子間をショート治具で約10秒間
接続する。
フラッシュユニットの電源コンデンサ
の端子間をショート治具で約10秒間
接続する。
C901
ST-276 Flexible
Board
Board
ST-276 Flexible
Board
Board
C901
DSC-HX200/HX200V_L2
2-3
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
4-418-113-01
RING (370), CAP (Note)
2
4-263-809-01
SHEET (CAP RING), ADHESIVE
3
4-279-877-01 RETAINER,
MODULE
4
4-286-551-01
SHEET (VF), RADIATION
5
A-1880-748-A SE-181 FLEXIBLE BOARD, COMPLETE (SERVICE)
6
4-279-878-01
CUSHION (EYE SENSOR)
7
X-2581-259-1 VF
ASSY
(970)
8
4-284-295-01 CUSHION
(VF-R)
LCD902 1-811-013-11
LCD MODULE (FL0906)
#2
2-635-562-31 SCREW
(M1.7)
1. Remove to numerical order (
1
to
3
) in the left figure.
◇-X
: Solder
DISASSEMBLY
1
#2 X 9
#2
#2
#2
1
Rear section
(See page 2-9)
(Claw)
Boards section
(See page 2-4)
#2
#2
2
7
LCD902
3
4
4
6
5
3
8
1
(Note)
2
#2
#2
Bottom View
Left View
Back View
#2
Note
Note :
How to Remove the Cap Ring
Solvent
Cap Ring
Tweezers
1
Turn on the power and pull out the lens to set.
2
Apply alcohol to gaps of the Cap Ring with tweezers
or a fine-tipped stick as shown in the figure below.
3
3
Detach the Cap Ring.
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
Note :
Solvent
Tweezers
1
電源を入れ、レンズを引き出す。
2
下図のように、ピンセットか先の細い棒で
アルコールを Cap Ring の隙間全周に塗布する。
3
3
Cap Ring を取り外す。
Cap Ring
Cap Ring の外し方
DSC-HX200/HX200V_L2
2-4
2-1-2. BOARDS SECTION
ns: not supplied
SY
-320
MS-485
A
A
A
A
A
A
ns
#12
#12
#12
#12
#12
#12
Lens section
(See page 2-5)
2
56
52
52
(Note)
51
53
(Note)
59
(Note)
55
57
: BT701 (LITHIUM RECHARGEABLE BATTERY)
Board on the mount position.
(See page 6-23 of Level 3)
Board on the mount position.
(See page 6-23 of Level 3)
BT701
SP901
J901
1
58
3
54
A
C
B
D
E
F
G
A
E
F
G
D
B
C
ns
ns
(Claws)
When re-assembling
Close lids.
(Note)
(Note)
1. Remove to numerical order (
1
to
3
) in the left figure.
◇-X
: Solder
DISASSEMBLY
1
#12 X 2
#12
Back View
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は、正しく行わないと破裂する恐れが
あります。電池を交換する場合には必ず同じ型名の
電池又は同等品と交換してください。使用済み電池は、
取扱指示に従って処分してください。
あります。電池を交換する場合には必ず同じ型名の
電池又は同等品と交換してください。使用済み電池は、
取扱指示に従って処分してください。
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
X-2583-787-1 COVER ASSY (370), JACK
52
4-284-291-01 GASKET
(SY)
(Note)
53
X-2583-786-1 HOLDER ASSY (370), SY
(Note)
54
A-1871-567-A SY-320 BOARD, COMPLETE (SERVICE)
(Note)
55
1-883-264-11
MS-463 FLEXIBLE BOARD
56
A-1864-700-A MS-485 BOARD, COMPLETE
57
4-270-079-01
SHEET (IC), RADIATION
58
4-279-788-01
PLATE (SY), GROUND
59
4-270-078-01
SHEET (CMOS), RADIATION
(Note)
BT701
1-756-813-11
LITHIUM RECHARGEABLE BATTERY
J901
1-842-734-11
JACK, D.C.
SP901 1-825-945-71 LOUDSPEAKER
(1.3CM)
#12
3-080-204-21 SCREW,
TAPPING,
P2
2
#12 X 1
3
#12 X 3
#12
Back View
#12
Back View
Note
Screw
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2012.05
Note: When this part is removed, adjustment is required.
For the adjustment method, refer to "Adjustment items after
replacing parts" in the Note tab of the Adjust manual.
replacing parts" in the Note tab of the Adjust manual.
Note: この部品を取り外したときは調整が必要です。
調整方法については Adjust manual の Noteタブにある
Adjustment items after replacing parts を参照してください。
Adjustment items after replacing parts を参照してください。
Click on the first or last page to see other DSC-HX200 / DSC-HX200V (serv.man2) service manuals if exist.