DOWNLOAD Sony DSC-F828 (serv.man2) Service Manual ↓ Size: 4.89 MB | Pages: 74 in PDF or view online for FREE

— 5 —

5-1-5. BTH BLOCK ASSEMBLY ············································· 5-7
5-1-6. CABINET (REAR) BLOCK ASSEMBLY ····················· 5-8
5-1-7. EVF ASSEMBLY ···························································· 5-9
5-2.

ELECTRICAL PARTS LIST ········································ 5-10

Parts list of the 

SY-096

 board are not shown.

Pages from 5-14 to 5-18 are not shown.

1-1

1 k

Ω

/1 W

Wrap insulating tape.

DD-204

DD-204 board 

Short jig

(1k

Ω

 /1W)

The charging capacitor of the FLASH unit is charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the capacitor is handled by hand.  The electric shock is caused by the charged
voltage which is kept without discharging when the main power of the DSC-F828 is simply turned off.  Therefore, the remaining voltage
must be discharged as described below.

To preparing the short jig. a small clip is attached to each end of a
resistor of 1 k

Ω

 /1 W (1-215-869-11)

Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.

Short circuits between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.

1-2E

Note : The error code is cleared if the battery is removed, except defective flash unit.

*1: The error display is given in two ways.

Display Code

C:32:01

C:13:01

E:91:01

E:61:00  *1

E:61:10  *1

Countermeasure

Turn off the main power then back on.

Replace the memory stick.
Format the memory stick with the DSC-F828.

Checking of flash unit or replacement of
flash unit.

Checking of lens drive circuit

Cause

Trouble with hardware.

• The type of memory stick that cannot be

used by this machine, is inserted.

• Data is damaged.
• Unformatted memory stick is inserted.

Abnormality when flash is being
charged.

When failed in the focus initialization.

Caution Display During Error

SYSTEM ERROR

MEDIA ERROR

Flash LED
Flash display
Flashing at 3.2 Hz

—

Self-diagnosis display
• C: ss: ss

The contents which can be handled
by customer, are displayed.

• E: ss: ss

The contents which can be handled
by engineer, are displayed.

The laser diode may suffer electrostatic breakdown because of the
potential difference generated by the charged electrostatic load, etc.
on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.

Laser unit 
(D001)

Temperature of

Less than 350 

°

C

the Soldering Iron

Time to Solder

3 seconds

Interval to Solder

Next terminal is soldered after waiting
for 1 second

Note: Adjustment is needed when laser unit is replaced.

Refer to “21. AF Laser Output Adjustment” (page6-29) and “22.
AF Laser Axis Check” (page6-30) of SERVICE MANUAL, ADJ
(987627951.pdf).

2-1

The following flow chart shows the disassembly procedure.

DD

-2

04

PROCEDURE OF REMOVING THE SY-096 BOARD (SERVICE POSITION)

1

2-1. 

CABINET (LR) ASSEMBLY, SW-410 BOARD ................................

2

2-2. 

STROBOSCOPE BLOCK ASSEMBLY ...........................................

3

2-9.

REAR CABINET BLOCK ASSEMBLY  ...........................................

4

2-13. BTH SECTION ..............................................................................

5

2-14. SY-096 BOARD .............................................................................

6

2-15. DD-204 BOARD ............................................................................

7

2-16. CF-097 BOARD ............................................................................

8

2-18. MEMORY STICK CONNECTOR ..................................................

9

2-20. DC-IN CONNECTOR,UA-003 BOARD .........................................

q;

2-21. FP-747/746/754 FLEXIBLE BOARD ............................................

qa

2-24. CABINET UPPER ASSEMBLY .....................................................

 (page 2-2)

(page 2-3)
(page 2-8)

(page 2-10)

(page 2-11)

(page 2-12)
(page 2-12)
(page 2-13)
(page 2-14)
(page 2-15)
(page 2-17)

Discharging the Capacitor

SY-096 board 
service position