DOWNLOAD Sony DSC-F828 (serv.man2) Service Manual ↓ Size: 4.89 MB | Pages: 74 in PDF or view online for FREE

2-6

6

 Tapping screw 

      

(M1.7 

× 

4)

8

 Claw

 (A) Section

7

 Open the ST unit holder section

(B)

4

 Tapping screw 

      

(M1.7 

× 

4)

3

 Tapping screw 

      

(M1.7 

× 

4)

5

 ST cover

1

2

9

 ST unit holder

qd

 SI-037 board

qa

 Remove soldering from the three points

qs

 Flash unit

ST unit holder

q;

 Two  claws

SI-037 board

Remove the ST unit holder from the SI-037 board by disengaging
the claw while sliding the (A) section of the SI-037 board in the 
direction of the arrow (B).

2-7

When soldering the laser unit on the LS-067 board,
observe the following things.
(Refer to Service Note (page 1-2)).
Observe the following conditions of temperature
and time of soldering.
Temperature of soldering iron : 350 

°

C

Time of contacting the soldering : 3 seconds
iron with the solder
The laser diode may suffer electrostatic breakdown
because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the
human body.
During repair, pay attention to electrostatic breakdown
and also use the procedure in the printed matter which
is included in the repair parts.
The flexible board is easily damaged and should be
handled with care.

1

 Tapping screw 

      

(M1.7 

× 

4)

4

 ST laser holder

3

 

Two grooves

7

 LS-067 board

2

 Two dowels

5

 Remove the

     three solderings

6

 Laser unit (D001)

2-8

8

 Rear cabinet block assembly

6

 LB-091 board 

    (22P)

7

 Control switch block (under) 

     (50P)

3

 Two screws 

(M2 

× 

4)

,

     lock ace

1

 Two screws 

(M2 

× 

4)

,  

     lock ace

The LB-091 board may be damaged if you
remove the rear cabinet block assembly  forcibly.
Be very careful not to damage the flexible board.

5

 Screw 

(M2 

× 

4)

, lock ace

2

 Screw 

(M2 

× 

4)

, 

     lock ace

4

 Screw 

(M2 

× 

4)

, 

     lock ace

3

 Three claws

7

 Two claws

6

 LCD (LCX044AK-1)

    (18P)

9

 Lamp guide (20)

1

 Four tapping screws 

      

(M1.7 

× 

4)

8

 LB-091 board

2

 EVF section

q;

 LCD (LCX044AK-1)

4

 Prism sheet 

5

 Illuminator

2-9

1

 Three screws (M1.7 

× 

3),

     lock ace

7

 

Control switch block

     (under)

5

 

Cabinet (rear) assembly

2

 

Control switch block 

     (mid)(10p)

3

 

Block light guide plate (6P)

4

 

LCD module (24P)

6

 

Tape (A)

Tape (A)

Control switch block (under)

Install the control switch block (under) in the
cabinet (rear) assembly so that the tip of the 
control switch block (under) go under the 
bottom of the control switch block (mid). 

1

 Five screws (M1.7 

× 

3),

     lock ace

7

 Two screws (M1.7 

× 

3),

     lock ace

2

 Open the CF lid

8

 CF lid assembly

3

 

Control switch block (mid)

5

 

Block light guide plate

Block light guide plate

6

 

LCD unit

4

 

Tape (A)

Tape (A)