Sony DSC-F717 (serv.man2) Service Manual ▷ View online
1-1
SECTION 1
SERVICE NOTE
DSC-F717
COVER
COVER
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
1-2. DISCHARGING OF THE BT-015 BOARD’S CHARGING CAPACITOR (C414, 415)
1 k
Ω
/1 W
Wrap insulating tape.
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some pieces of
gilt may be left inside)
which comes off at the point.
(Be careful or some pieces of
gilt may be left inside)
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
CN404
BT-015
Harness
The charging capacitor (C414, 415) of BT-015 is charged up to the
maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
battery is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
battery is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
1-2-1. Preparing the Short Jig
To preparing the short jig. a small clip is attached to each end of a
resistor of 1 k
resistor of 1 k
Ω
/1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
electrical shock.
1-2-2. Discharging the Capacitor
1. Remove the FR-194 board, and disconnect the harness from
CN404 on the BT-015 board.
2. Connect the short jig to the pin 1 and pin 2 of CN404 on
BT-015 board. Allow ten seconds to discharge the voltage.
1-2E
DSC-F717
Laser unit
(D001)
(D001)
Display Code
C:32:ss
C:13:ss
E:61:ss
E:91:ss
Countermeasure
Turn the power off and on again.
Format the “Memory stick”.
Insert a new “Memory Stick”.
Cause
Trouble with hardware.
Unformatted memory stick is inserted.
Memory stick is broken.
When failed in the focus and zoom
initialization.
initialization.
Abnormality when flash is being
charged.
charged.
Caution Display During Error
SYSTEM ERROR
FORMAT ERROR
MEMORY STICK ERROR
—
Self-diagnosis display
• C: ss: ss
You can reverse the camera mal-
function yourself. (However, con-
tact your Sony dealer or local
authorized Sony service facility
when you cannot recover from
the camera malfunction.)
function yourself. (However, con-
tact your Sony dealer or local
authorized Sony service facility
when you cannot recover from
the camera malfunction.)
• E: ss: ss
Contact your Sony dealer or lo-
cal authorized Sony service facil-
ity.
cal authorized Sony service facil-
ity.
1-4. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Checking of lens drive circuit.
Checking of flash unit or replacement
of flash unit.
of flash unit.
1-3. NOTES ON HANDLING THE LASER DIODE
[LASER UNIT (D001)]
The laser diode may suffer electrostatic breakdown because of the
potential difference generated by the charged electrostatic load, etc.
on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
potential difference generated by the charged electrostatic load, etc.
on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
Note:
Adjustment is needed when laser unit (D001) is replaced.
Refer to “27. LED Illumination Check” and “28. AF
Illumination Check” of SERVICE MANUAL, ADJ
(992999451.pdf).
Refer to “27. LED Illumination Check” and “28. AF
Illumination Check” of SERVICE MANUAL, ADJ
(992999451.pdf).
2-1
SECTION 2
DISASSEMBLY
DSC-F717
COVER
COVER
2-1. CABINET (REAR)
ASSEMBLY
(Page 2-2)
(Page 2-2)
2-7. CABINET (LL)
ASSEMBLY
(Page 2-5)
(Page 2-5)
2-7. CABINET (LL)
ASSEMBLY
(Page 2-5)
(Page 2-5)
2-8. CABINET (MF)
ASSEMBLY
(Page 2-5)
(Page 2-5)
2-14. CABINET (L) BLOCK
ASSEMBLY
(Page 2-8)
(Page 2-8)
2-9. LENS COMPLETE
ASSEMBLY
(Page 2-6)
(Page 2-6)
2-2. EVF ASSEMBLY
(Page 2-2)
2-3. PD-179 BOARD
(Page 2-3)
2-6. SW-379 BOARD
(Page 2-3)
2-10. SY-080 BOARD
(Page 2-7)
2-12. FR-194 BOARD
(Page 2-8)
2-13. BT-015 BOARD
(Page 2-8)
2-11. CONTROL SWITCH
BLOCK (FZ51050)
(Page 2-7)
(Page 2-7)
2-5. AL-013 BOARD,
DC-IN JACK
(Page 2-3)
(Page 2-3)
2-4. LCD MODULE
(Page 2-3)
DSC-F717
SERVICE POSITION
(FR-194 BOARD: SIDE B)
(Page 2-4)
(FR-194 BOARD: SIDE B)
(Page 2-4)
SERVICE POSITION
(FR-194 BOARD: SIDE A)
(Page 2-4)
(FR-194 BOARD: SIDE A)
(Page 2-4)
SERVICE POSITION
(PD-179 BOARD)
(Page 2-5)
(PD-179 BOARD)
(Page 2-5)
SERVICE POSITION
(SY-080 BOARD: SIDE B)
(Page 2-6)
(SY-080 BOARD: SIDE B)
(Page 2-6)
SERVICE POSITION
(SY-080: SIDE A AND CD-408 BOARDS)
(Page 2-7)
(SY-080: SIDE A AND CD-408 BOARDS)
(Page 2-7)
TO FOLD THE NEW
FP-617 FLEXIBLE BOARD
(Page 2-9)
FP-617 FLEXIBLE BOARD
(Page 2-9)
2-17. FLASH UNIT
(Page 2-10)
2-16. STROBOSCOPE
BLOCK ASSEMBLY
(Page 2-10)
(Page 2-10)
2-15. FP-617 FLEXIBLE
BOARD (Page 2-9)
The following flow chart shows the disassembly procedure.
2-2
DSC-F717
2-2. EVF ASSEMBLY
2-1. CABINET (REAR) ASSEMBLY
Note:
Follow the disassembly procedure in the numerical order given.
2
Two screws
(2.0)
(2.0)
6
Connector
(CN401)
(CN401)
1
Screw
(M1.7)
(M1.7)
3
Screw
(M1.7)
(M1.7)
7
Cabinet (rear)
assembly
assembly
4
Cabinet (rear) assembly
5
Flexible board
(CN308)
(CN308)
2
Flexible board
(CN704)
(CN704)
1
Copy sheet (LB)
4
EVF assembly
EVF assembly
3
Two screws
(DIA.1.7
(DIA.1.7
×
4.5)
Click on the first or last page to see other DSC-F717 (serv.man2) service manuals if exist.