Sony DSC-F55V (serv.man2) Service Manual ▷ View online
— 5 —
SERVICE NOTE
• NOTE FOR REPAIR
[Discharging of the FLASH unit’s charging capacitor]
The charging capacitor of the FLASH unit is charged up to the
maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the DSC-F55V is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the DSC-F55V is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig. a small clip is attached to each end of a
resistor of 1 k
resistor of 1 k
Ω
/1 W (1-215-869-11)
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
When remove a connector, don't pull at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
Discharging the Capacitor
Short circuits between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
charged capacitor with the short jig about 10 seconds.
FLASH UNIT
Short jig
Capacitor
— 6 —
Note :
The error code is cleared if the battery is removed, except defective flash unit.
*1: The error display is given in two ways.
*2: When the flash charginf failed, Page: D, Address: 67, Data:04 are written.
After repair, be sure to write Page: D, Address: 67, Data: 00.
*1: The error display is given in two ways.
*2: When the flash charginf failed, Page: D, Address: 67, Data:04 are written.
After repair, be sure to write Page: D, Address: 67, Data: 00.
Display Code
C:32:01
C:13:01
E:91:01
E:61:00 *1
E61:10 *1
Countermeasure
Turn off the main power then back on.
Replace the memory stick.
Format the memory stick with the DSC-
F55V.
Format the memory stick with the DSC-
F55V.
Checking of flash unit or replacement of
flash unit
flash unit
Checking of lens drive circuit
Cause
Trouble with hardware.
• The type of memory stick that cannot
be used by this machine, is inserted.
• Data is damaged.
• Unformatted memory stick is inserted.
• Unformatted memory stick is inserted.
Abnormality when flash is being
charged. *2
charged. *2
When failed in the focus initialization.
Caution Display During Error
SYSTEM ERROR
MS ERROR
Flash LED
Flash display
Flashing at 3.2 Hz
Flash display
Flashing at 3.2 Hz
—
Self-diagnosis display
• C: ss: ss
The contents which can be handled
by customer, are displayed.
by customer, are displayed.
• E: ss: ss
The contents which can be handled
by engineer, are displayed.
by engineer, are displayed.
[Description on Self-diagnosis Display]
1-1
DSC-F55V
SECTION 1
GENERAL
This section is extracted from
instruction manual.
instruction manual.
1-2
Click on the first or last page to see other DSC-F55V (serv.man2) service manuals if exist.