Sony XR-M500R / XR-M550 Service Manual ▷ View online
21
A
part
C
part
B
part
D
part
8
Hold the hanger by
bending the claw.
bending the claw.
6
Fit projection on D part.
4
Fit claw on B part.
3
Put the housing
under A part.
under A part.
5
Fit projection on C part.
1
Install the catch to the hanger.
2
Install the hanger onto
two claws of the housing.
two claws of the housing.
7
Holder the hanger by bending the claw.
hanger
housing
4-2.
MECHANISM DECK
HOUSING
ARM (SUCTION)
2
Move the arm (suction) in the arrow
direction and fit on projection.
direction and fit on projection.
1
Fit the arm (suction) on the shaft.
projection
22
LEVER (LDG-A) / (LDG-B)
GEAR (LDG-FT)
shaft A
shaft B
shaft C
1
Fit the lever (LDG-A) on
shafts A – C and install it.
shafts A – C and install it.
shaft A
shaft B
2
Fit the lever (LDG-B) on
shafts A and B and
install it.
shafts A and B and
install it.
3
type-E stop ring 2.0
gear (LDG-D)
5
gear (LDG-FT)
6
polyethylene washer
2
tension spring (LD-2)
2
tension spring (LD-1)
gear (LDG-FB)
lever (LDG-A)
hole
hole
4
Align hole in the gear (LDG-D)
with hole the lever (LDG-A).
with hole the lever (LDG-A).
3
Move the lever (LDG-B)
in the arrow direction.
in the arrow direction.
1
23
GUIDE (C)
MOUNTING POSITION OF CAPSTAN/REEL MOTOR (M901)
2
guide (C)
1
three claws
two precision screws
(P2
(P2
×
2)
capstan/reel motor
(M901)
(M901)
30˚
24
SECTION 5
MECHANICAL ADJUSTMENTS
SECTION 6
ELECTRICAL ADJUSTMENTS
Mode
Tension Meter
Meter Reading
Forward
CQ-403A
more than 90 g
(more than 3.18 oz)
Reverse
CQ-403R
more than 90 g
(more than 3.18 oz)
• Tape Tension Measurement
1. Clean the following parts with a denatured-alcohol-moistened
swab:
playback head
pinch roller
rubber belt
capstan
idler
2. Demagnetize the playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. The adjustments should be performed with the power supply
3. Do not use a magnetized screwdriver for the adjustments.
4. The adjustments should be performed with the power supply
voltage (14.4 V) unless otherwise noted.
• Torque Measurement
Mode
Torque Meter
Meter Reading
2.95 – 6.73 mN•m
Forward
CQ-102C
30 – 65 g•cm
(0.42 – 0.90 oz•inch)
Forward
0.05 – 0.44mN•m
CQ-102C
0.5 – 4.5 g•cm
Back Tension
(0.01 – 0.06 oz•inch)
2.95 – 6.73 mN•m
Reverse
CQ-102RC
(25 – 55 g•cm)
(0.42 – 0.90 oz•inch)
Reverse
0.05 – 0.44mN•m
CQ-102RC
0.5 – 4.5 g•cm
Back Tension
(0.01 – 0.06 oz•inch)
5.89 – 19.61 mN•m
FF, REW
CQ-201B
60 – 200 g•cm)
(0.83 – 2.78 oz•inch)
TEST MODE
<Set the Test Mode>
1. Turn ON the regulated power supply. (All LEDs on the set
1. Turn ON the regulated power supply. (All LEDs on the set
lights up, and the clock is displayed.)
Note:
Press the
[OFF]
button, if the clock is not displayed.
2. Push the preset
[4]
button.
3. Push the preset
[5]
button.
4. Press the preset
[1]
button for more than two seconds.
5. Then the display indicates all lights, the test mode is set.
<Release the Test mode>
1. Push the
1. Push the
[OFF]
button.
Tape Speed Adjustment
Setting:
Procedure:
1. Put the set into the FWD PB mode.
2. Adjust adjustment resistor for inside capstan motor so that the
1. Put the set into the FWD PB mode.
2. Adjust adjustment resistor for inside capstan motor so that the
reading on the speed checker or frequency counter becomes in
specification.
specification.
Specification: Constant speed
Adjustment Location: See page 25.
0 dB=0.775 V
TAPE DECK SECTION
Speed checker
Frequency counter
–1.5 to +2.5%
2,955 to 3,075 Hz
set
+
–
test tape
WS-48A
(3 kHz, 0 dB)
WS-48A
(3 kHz, 0 dB)
AUDIO OUT REAR jack (CN300)
10 k
Ω
speed checker
or
frequency counter
See the adjustment location from on page 25 for the
adjustment.
adjustment.
Click on the first or last page to see other XR-M500R / XR-M550 service manuals if exist.