Sony XR-CA400 / XR-CA410 Service Manual ▷ View online
XR-CA400/CA410
21
21
6-7.
SCHEMATIC DIAGRAM – KEY Board –
•
See page 13 for Waveform.
(Page 19)
XR-CA400/CA410
22
22
6-8.
IC PIN FUNCTION DESCRIPTION
•
MAIN BOARD IC501 MN101C49KTC (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
VREF–
I
Reference voltage (0V) input terminal (for A/D converter)
2
VSM
I
FM and AM signal meter voltage detection signal input from the FM/AM tuner unit (TU1)
(A/D input)
(A/D input)
3
NIL
I
Not used (fixed at “L”)
4
KEYIN1
I
Key input terminal (A/D input) S907, S908, LSW905 to LSW915
(SEEK/AMS – . m, SEEK/AMS + > M, MBP, D-BASS D, DSPL, MTL PTY, TA,
ATA 6, BL SKIP 5, SHUF 4, REP 3, 2 DISC +, 1 DISC– keys input)
(SEEK/AMS – . m, SEEK/AMS + > M, MBP, D-BASS D, DSPL, MTL PTY, TA,
ATA 6, BL SKIP 5, SHUF 4, REP 3, 2 DISC +, 1 DISC– keys input)
5
KEYIN0
I
Key input terminal (A/D input) S901 to S906, LSW901 to LSW904 (OFF, SRC SOURCE, +
(VOLUME), – (VOLUME), MODE o, SEL, Z, ATF, BTM SENS, AF keys input)
(VOLUME), – (VOLUME), MODE o, SEL, Z, ATF, BTM SENS, AF keys input)
6
RCIN0
I
Rotary remote commander key input terminal (A/D input)
7
QUALITY
I
Noise level detection signal input at SEEK mode (A/D input)
8
MPTH
I
Multi-path detection signal input from the RDS decoder (IC51) (A/D input)
9
NIL
I
Not used (fixed at “L”)
10
VREF+
I
Reference voltage (+5V) input terminal (for A/D converter)
11
VDD
—
Power supply terminal (+5V)
12
OSCOUT
O
Main system clock output terminal (18.432 MHz)
13
OSCIN
I
Main system clock input terminal (18.432 MHz)
14
VSS
—
Ground terminal
15
XI
I
Sub system clock input terminal (32.768 kHz)
16
XO
O
Sub system clock output terminal (32.768 kHz)
17
MMOD
I
Selection signal of memory mode input terminal “L”:single chip mode (fixed at “L”)
18
LCDSO
O
Serial data output to the liquid crystal display driver (IC901)
19
LCDCE
O
Chip enable signal output to the liquid crystal display driver (IC901) “H” active
20
LCDCKO
O
Serial data transfer clock signal output to the liquid crystal display driver (IC901)
21 to 23
NCO
O
Not used (open)
24
SYSRST
O
Reset signal output to the SONY bus interface (IC581) “L”: reset
25
BUSON
O
Bus on/off control signal output to the SONY bus interface (IC581) “L”: bus on
26
KEYACK
I
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function
and eject keys in the power off status On at input of “H”
and eject keys in the power off status On at input of “H”
27
DAVN
I
Synchronized detection signal of RDS data block input from the RDS decoder (IC51)
“H” active
“H” active
28
BUIN
I
Battery detection signal input from the SONY bus interface (IC581)
“L” is input at low voltage
“L” is input at low voltage
29
SIRCS
I
SIRCS remote control signal input terminal Not used (open)
30, 31
NIL
I
Not used (fixed at “L”)
32
NIH
I
Not used (fixed at “H”)
33
RESET
I
System reset signal input from the reset signal generator (IC551) and reset switch (S551)
“L”: reset “L” is input for several 100 msec after power on, then it changes to “H”
“L”: reset “L” is input for several 100 msec after power on, then it changes to “H”
34
TUNON
O
Tuner system power supply on/off control signal output “H”: tuner power on
35
BEEP
O
Beep sound drive signal output to the power amplifier (IC751)
36
PW_ON
O
Main system power supply on/off control signal output “H”: power on
37
NCO
I
Not used (open)
38
ACCIN
I
Accessory detection signal input “L”: accessory on
39
NCO
O
Not used (open)
40
TELATT
I
Telephone attenuate signal input At input of “H”, the signal is attenuated by –20 dB
41
NIH
I
Not used (fixed at “H”)
42
BUSSO
O
Serial data output to the SONY bus interface (IC581)
43
BUSSI
I
Serial data input from the SONY bus interface (IC581)
Pin No.
Pin Name
I/O
Description
44
BUSCKO
O
Serial data transfer clock signal output to the SONY bus interface (IC581)
45
IIC SIO
I/O
Two-way data IIC bus with the FM/AM tuner unit (TU1), RDS decoder (IC51) and electrical
volume (IC331)
volume (IC331)
46
NCO
O
Not used (open)
47
IIC CKO
O
IIC bus clock signal output to the FM/AM tuner unit (TU1), RDS decoder (IC51) and electrical
volume (IC331)
volume (IC331)
48
AMPON
O
Standby on/off control signal output to the power amplifier (IC751)
“L”: standby mode, “H”: amplifier on
“L”: standby mode, “H”: amplifier on
49
AMPATT
O
Muting on/off control signal output to the power amplifier (IC751) “L”: muting on
50
ATT
O
Audio line muting on/off control signal output “H”: muting on
51
NCO
O
Not used (open)
52
AMSON
O
Tape auto music sensor control signal output to the CXA2509AQ (IC301)
“L”: auto music sensor on
“L”: auto music sensor on
53
F/ROUT
O
Forward/reverse control signal output to the CXA2509AQ (IC301)
“L”: reverse direction, “H”: forward direction
“L”: reverse direction, “H”: forward direction
54
MTLON
O
METAL on/off control signal output to the CXA2509AQ (IC301) “H”: METAL on
55
TAPATT
O
Tape muting on/off control signal output to the CXA2509AQ (IC301) “H”: muting on
Active at ATA, FF/REW mode
Active at ATA, FF/REW mode
56
NCO
O
Not used (open)
57
AMSIN
I
Whether a music is present or not from CXA2509AQ (IC301) is detected at auto music sensor
“L”: music is present, “H”: music is not present
“L”: music is present, “H”: music is not present
58
NCO
O
Not used (open)
59
VOLATT
O
Pre amplifier muting on/off control signal output to the electrical volume (IC331)
“L”: muting on
“L”: muting on
60 to 64
NCO
O
Not used (open)
65
FLASH_W
I
Internal flash memory data write mode detection signal input terminal “L”: data write mode
Not used (open)
Not used (open)
66
TESTIN
I
Setting terminal for the test mode “L”: test mode, normally fixed at “H”
67
RCIN1
I
Rotary remote commander shift key input terminal “L”: shift key on
68 to 73
NCO
O
Not used (open)
74
EEP SIO
I/O
Two-way data bus for tuner EEPROM with the FM/AM tuner unit (TU1)
75
EEP CKO
I/O
Two-way bus clock signal for tuner EEPROM with the FM/AM tuner unit (TU1)
76
COLSEL
I
Setting terminal for the illumination color
“L”: amber (XR-CA410: AMBER), “H”: green (XR-CA400/CA410: GREEN)
“L”: amber (XR-CA410: AMBER), “H”: green (XR-CA400/CA410: GREEN)
77 to 81
NCO
O
Not used (open)
82
AD ON
O
A/D converter power control signal output terminal
When the KEYACK (pin wh) that controls reference voltage power for key A/D conversion input
is active, “L” is output from this terminal to enable the input
When the KEYACK (pin wh) that controls reference voltage power for key A/D conversion input
is active, “L” is output from this terminal to enable the input
83
ILLON
O
Power on/off control signal output of the illumination LED and liquid crystal display driver
(IC901) “H”: power on
(IC901) “H”: power on
84
REL
I
Rotation detection signal input from supply reel sensor and take-up reel sensor on the mechanism
deck
deck
85
POS3
I
86
POS2
I
87
POS0
I
88
POS1
I
89
LMLOD
O
Motor drive signal output to the loading motor drive (IC351) “H” active
(For the loading direction and forward side operation) *1
(For the loading direction and forward side operation) *1
90
LMEJ
O
Motor drive signal output to the loading motor drive (IC351) “H” active
(For the eject direction and reverse side operation) *1
(For the eject direction and reverse side operation) *1
Tape position (EJECT/FF/REW/REV/
FWD mode) detect input from the tape
operation switch on the deck mechanism
FWD mode) detect input from the tape
operation switch on the deck mechanism
POS3: “L”: REV and EJECT mode, “H”: others mode
POS2: “L”: REW mode, “H”: others mode
POS0: “L”: EJECT mode, “H”: others mode
POS1: “L”: FF and FWD mode, “H”: others mode
POS2: “L”: REW mode, “H”: others mode
POS0: “L”: EJECT mode, “H”: others mode
POS1: “L”: FF and FWD mode, “H”: others mode
23
XR-CA400/CA410
Pin No.
Pin Name
I/O
Description
91
TAPEON
O
Power on/off control signal output of the loading motor drive (IC351) and capstan/reel motor
(M901) “H”: motor on
(M901) “H”: motor on
92
CMON
O
Capstan/reel motor (M901) drive signal output terminal “H”: motor on
93
NOSESW
I
Front panel block remove/attach detection signal input
“L”: front panel is attached, “H”: front panel is removed
“L”: front panel is attached, “H”: front panel is removed
94
NS_MASK
O
Discharge control signal output for the noise detection circuit “H”: discharge
95
DAVSS
—
Ground terminal (for D/A converter)
96 to 99
NCO
O
Not used (open)
100
DAVCC
—
Power supply terminal (+5V) (for D/A converter)
*1 Loading motor control
STOP
LOADING/
FORWARD
EJECT/
REVERSE
BRAKE
LMLOD (pin il )
“L”
“H”
“L”
“H”
LMEJ (pin o; )
“L”
“L”
“H”
“H”
Terminal
Mode
24
XR-CA400/CA410
MG-25L-136
14
13
15
16
18
19
20
17
1
2
5
6
8
7
10
12
11
9
3
4
Front panel assy
#1
#1
#2
F781
TU1
#3
#3
#3
#3
#1
#1
A
A
B
B
(1)
CHASSIS SECTION
SECTION 7
EXPLODED VIEWS
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
electrical parts list.
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
1
3-042-244-11 SCREW (T)
2
X-3370-437-1 LOCK ASSY
3
3-027-437-51 DOOR, CASSETTE
4
3-935-003-01 SPRING, TORSION
* 5
3-033-846-01 INSULATED PLATE
* 6
3-046-991-01 SPACER (COVER R)
* 7
3-046-990-01 SPACER (COVER L)
* 8
3-040-995-11 COVER
* 9
A-3326-771-A MAIN BOARD, COMPLETE (CA410: AMBER)
* 9
A-3326-772-A MAIN BOARD, COMPLETE
(CA400/CA410: GREEN)
10
3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT
* 11
3-224-902-01 HEAT SINK (REG)
* 12
3-040-998-01 BRACKET (IC)
* 13
3-224-899-01 HEAT SINK (ISO)
14
3-012-859-01 CAP (25), RUBBER
* 15
3-045-878-01 PLATE (TU), GROUND
* 16
3-045-877-01 CUSHION (TU)
17
1-782-381-11 CORD (WITH CONNECTOR) (ISO P&S)
(POWER) (South European)
18
1-777-989-41 CORD (WITH CONNECTOR) (AMP REM/ATT)
19
3-224-862-01 PANEL, SUB
20
3-009-813-52 CHASSIS
F781
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)
TU1
A-3220-812-A FM/AM TUNER UNIT (TUX-020)
Click on the first or last page to see other XR-CA400 / XR-CA410 service manuals if exist.